DTC C1622 Back Camera Disconnected |
| DTC No. | DTC Detection Condition | Trouble Area |
| C1622 | Open or short in the rear television camera assembly signal circuit |
|

| 1.CONFIRM MODEL |
Choose the model to be inspected.
| Result | Proceed to |
| for Navigation System (for Navigation Receiver Type) | A |
| for Audio and Visual System (for Radio and Display Type) | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY) |
Disconnect the I184 navigation receiver assembly connector.
Disconnect the T6 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I184-11 (CA+) - T6-6 (CB+) | Always | Below 1 Ω |
| I184-12 (V+) - T6-3 (CV+) | Always | Below 1 Ω |
| I184-24 (V-) - T6-2 (CV-) | Always | Below 1 Ω |
| I184-23 (CGND) - T6-5 (CGND) | Always | Below 1 Ω |
| I184-11 (CA+) - Body ground | Always | 10 kΩ or higher |
| I184-12 (V+) - Body ground | Always | 10 kΩ or higher |
| I184-24 (V-) - Body ground | Always | 10 kΩ or higher |
| I184-23 (CGND) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.INSPECT NAVIGATION RECEIVER ASSEMBLY |
Reconnect the I184 navigation receiver assembly connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I184-23 (CGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I184-11 (CA+) - I184-23 (CGND) | Ignition switch ACC | 5.5 to 7.05 V |
| *a | Component with harness connected (Navigation Receiver Assembly) |
| Result | Proceed to |
| OK | A |
| NG (for TMC, TMMR Made) | B |
| NG (for TMMK Made) | C |
|
| ||||
|
| ||||
| A | |
| 4.INSPECT REAR TELEVISION CAMERA ASSEMBLY |
Reconnect the T6 rear television camera assembly connector.
![]() ![]() |
Using an oscilloscope, check the waveform of the rear television camera assembly.
| *a | Component with harness connected (Navigation Receiver Assembly) |
| Item | Content |
| Measurement terminal | I184-12 (V+) - I64-7 (GND1) |
| Measurement setting | 200 mV/DIV., 50 μs./DIV. |
| Condition | Ignition switch ON, shift lever in R |
| *a | Waveform 1 (camera lens is not covered, displaying an image) |
| *b | Waveform 2 (camera lens is covered, blacking out the screen) |
| *c | Synchronization Signal |
| *d | Video Waveform |
| Result | Proceed to |
| OK (for TMC, TMMR Made) | A |
| OK (for TMMK Made) | B |
| NG (for TMC, TMMR Made) | C |
| NG (for TMMK Made) | D |
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY) |
Disconnect the I185 radio and display receiver assembly connector.
Disconnect the T6 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I185-11 (CA+) - T6-6 (CB+) | Always | Below 1 Ω |
| I185-12 (V+) - T6-3 (CV+) | Always | Below 1 Ω |
| I185-24 (V-) - T6-2 (CV-) | Always | Below 1 Ω |
| I185-23 (CGND) - T6-5 (CGND) | Always | Below 1 Ω |
| I185-11 (CA+) - Body ground | Always | 10 kΩ or higher |
| I185-12 (V+) - Body ground | Always | 10 kΩ or higher |
| I185-24 (V-) - Body ground | Always | 10 kΩ or higher |
| I185-23 (CGND) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY |
Reconnect the I185 radio and display receiver assembly connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I185-23 (CGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I185-11 (CA+) - I185-23 (CGND) | Ignition switch ACC | 5.5 to 7.05 V |
| *a | Component with harness connected (Radio and Display Receiver Assembly) |
| Result | Proceed to |
| OK | A |
| NG (for TMC, TMMR Made) | B |
| NG (for TMMK Made) | C |
|
| ||||
|
| ||||
| A | |
| 7.INSPECT REAR TELEVISION CAMERA ASSEMBLY |
Reconnect the T6 rear television camera assembly connector.
![]() ![]() |
Using an oscilloscope, check the waveform of the rear television camera assembly.
| *a | Component with harness connected (Radio and Display Receiver Assembly) |
| Item | Content |
| Measurement terminal | I185-12 (V+) - I152-7 (GND1) |
| Measurement setting | 200 mV/DIV., 50 μs./DIV. |
| Condition | Ignition switch ON, shift lever in R |
| *a | Waveform 1 (camera lens is not covered, displaying an image) |
| *b | Waveform 2 (camera lens is covered, blacking out the screen) |
| *c | Synchronization Signal |
| *d | Video Waveform |
| Result | Proceed to |
| OK (for TMC, TMMR Made) | A |
| OK (for TMMK Made) | B |
| NG (for TMC, TMMR Made) | C |
| NG (for TMMK Made) | D |
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||