Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type)

DTC    B1532    LVDS Signal Malfunction (from Extension Module)

for Preparation Click here


DESCRIPTION

The navigation ECU and the radio and display receiver assembly are connected via LVDS communication line.
This DTC is stored when an LVDS communication error occurs between the navigation ECU and the radio and display receiver assembly.

DTC No.
DTC Detection Condition
Trouble Area
B1532
When any of the following conditions is met:
  1. Video signal (digital) is lost
  2. Navigation ECU is not connected while the ignition switch is ACC or ON
  3. Communication between the radio and display receiver assembly and the navigation ECU is not possible when the engine is started
  1. Navigation ECU power source circuit
  2. LVDS circuit between radio and display receiver assembly and navigation ECU
  3. Navigation ECU
  4. Radio and display receiver assembly
  5. No. 1 navigation wire

HINT:
Even if no malfunction is present, this DTC may be stored depending on the battery condition or engine start voltage.


WIRING DIAGRAM


E276665E21


INSPECTION PROCEDURE

1.CHECK NO. 1 NAVIGATION WIRE (NAVIGATION ECU POWER SOURCE)
  1. Disconnect the k3 navigation ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    k3-8 (GND2) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    k3-4 (+B2) - k3-8 (GND2)
    Always
    11 to 14 V
    k3-3 (ACC2) - k3-8 (GND2)
    Ignition switch ACC
    11 to 14 V



NG
Go to step 4
OK


2.REPLACE NO. 1 NAVIGATION WIRE
  1. Replace the No. 1 navigation wire with a new or known good one (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check that no DTCs are output.

    OK:
    No DTCs are output.



NG
Go to step 3
OK

END 

3.REPLACE NAVIGATION ECU
  1. Replace the navigation ECU with a new or known good one (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check that no DTCs are output.

    OK:
    No DTCs are output.



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK

END 

4.CHECK NO. 1 NAVIGATION WIRE
  1. Disconnect the k2 radio and display receiver assembly connector.

  1. Disconnect the k3 navigation ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance::
    Tester Connection
    Condition
    Specified Condition
    k2-4 (+B2) - k3-4 (+B2)
    Always
    Below 1 Ω
    k2-3 (ACC2) - k3-3 (ACC2)
    Always
    Below 1 Ω
    k2-8 (GND2) - k3-8 (GND2)
    Always
    Below 1 Ω
    k2-4 (+B2) - Body ground
    Always
    10 kΩ or higher
    k2-3 (ACC2) - Body ground
    Always
    10 kΩ or higher
    k2-8 (GND2) - Body ground
    Always
    10 kΩ or higher



NG
REPLACE NO. 1 NAVIGATION WIRE (Click here)
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)