Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/o Smart Entry and Start System)

ENGINE IMMOBILISER SYSTEM (w/o Smart Entry and Start System) > Engine does not Start but Initial Combustion Occurs

for Preparation Click here


DESCRIPTION

If the key ID codes of the door control transmitter assembly and transponder key ECU assembly match, the engine immobiliser system is unset and the engine start permission signal is sent to the ECM. When the ID codes of the transponder key ECU assembly and ECM match, the engine starts.

WIRING DIAGRAM


B255097E04


INSPECTION PROCEDURE

NOTICE:
If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.

1.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2.CHECK FOR DTC
  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTCs are not output
    A
    DTCs are output
    B



B
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
A


3.READ VALUE USING INTELLIGENT TESTER (IMMOBILISER FUEL CUT)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Engine and ECT (ECM) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Immobiliser Fuel Cut
    Status of immobiliser fuel cut / ON or OFF
    -
    -

    OK:
    OFF is displayed after the ignition switch to ON.

    Result:
    Result
    Proceed to
    NG
    A
    OK
    B



B
GO TO SFI SYSTEM (Click here)
A


4.CHECK WHETHER ENGINE STARTS
  1. Using a registered door control transmitter assembly, turn the ignition switch to ON.

  1. Check that the engine starts 5 seconds after the ignition switch was turned to ON.

    OK:
    Engine starts normally.

    Result:
    Result
    Proceed to
    NG
    A
    OK
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A


5.CHECK ECM (TERMINAL IMI)


  1. Using an oscilloscope, check the waveform.


    B372936E01


    Text in Illustration 
    *a
    Component with harness connected
    (ECM)
    *b
    Component with harness connected
    (Transponder Key ECU Assembly)
    *c
    Waveform 1
    *d
    Waveform 2
    *e
    Approximately 160 ms
    *f
    Approximately 270 ms

    Measurement Condition:

    Tester Connection
    Condition
    Tool Setting
    Specified Condition
    A25-28 (IMI) - I19-13 (EFIO)
    Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal
    2 V/DIV., 500 ms./DIV.
    Pulse generation
    (See waveform)

    Result:
    Result
    Proceed to
    Normal waveform
    A
    Waveform 1 not output, or has abnormal wavelength or shape
    B
    Waveform 2 not output, or has abnormal wavelength or shape
    C



B
Go to step 12

C
Go to step 13
A


6.CHECK ECM (TERMINAL IMO)


  1. Using an oscilloscope, check the waveform.


    B372937E01


    Text in Illustration 
    *a
    Component with harness connected
    (ECM)
    *b
    Component with harness connected
    (Transponder Key ECU Assembly)
    *c
    Waveform
    *d
    Approximately 160 ms
    *e
    Approximately 270 ms
    -
    -

    Measurement Condition:

    Tester Connection
    Condition
    Tool Setting
    Specified Condition
    A25-29 (IMO) - I19-12 (EFII)
    Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal
    2 V/DIV., 500 ms./DIV.
    Pulse generation
    (See waveform)

    Result:
    Result
    Proceed to
    Normal waveform
    A
    Waveform not output, or has abnormal wavelength or shape
    B



B
Go to step 9
A


7.REGISTER ECU COMMUNICATION ID
  1. Register the communication ID between the transponder key ECU assembly and ECM.

    HINT:
    Refer to Service Bulletin.


NEXT


8.CHECK WHETHER ENGINE STARTS
  1. Using a registered door control transmitter assembly, turn the ignition switch to ON.

  1. Check that the engine starts 5 seconds after the ignition switch was turned to ON.

    OK:
    Engine starts normally.



NG
Go to step 13
OK

END (REGISTERED COMMUNICATION ID WAS DEFECTIVE) 

9.REPLACE ECM
  1. Temporarily replace the ECM with a new one (Click here).


NEXT


10.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID.

    HINT:
    Refer to Service Bulletin.


NEXT


11.CHECK WHETHER ENGINE STARTS
  1. Using a registered door control transmitter assembly, turn the ignition switch to ON.

  1. Check that the engine starts 5 seconds after the ignition switch was turned to ON.

    OK:
    Engine starts normally.



NG
GO TO SFI SYSTEM (Click here)
OK

END (ECM WAS DEFECTIVE) 

12.CHECK HARNESS AND CONNECTOR ((TRANSPONDER KEY ECU ASSEMBLY - ECM)
  1. Disconnect the I19 transponder key ECU assembly connector.

  1. Disconnect the A25 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I19-13 (EFIO) - A25-28 (IMI)
    Always
    Below 1 Ω
    I19-13 (EFIO) or A25-28 (IMI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13.REPLACE TRANSPONDER KEY ECU ASSEMBLY
  1. Replace the transponder key ECU assembly with a new one.

    HINT:
    Refer to Service Bulletin.

    NOTICE:
    Key ID code registration is necessary when replacing the transponder key ECU assembly, refer to Service Bulletin.


NEXT


14.CHECK WHETHER ENGINE STARTS
  1. Using a registered door control transmitter assembly, turn the ignition switch to ON.

  1. Check that the engine starts 5 seconds after the ignition switch was turned to ON.

    OK:
    Engine starts normally.



NG
GO TO SFI SYSTEM (Click here)
OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)