NAVIGATION SYSTEM (for Radio and Display Type) > SYSTEM DESCRIPTION |
| NAVIGATION SYSTEM OUTLINE |
Vehicle position tracking methods
It is essential that the navigation system correctly tracks the current vehicle position and displays it on the map. There are 2 methods to track the current vehicle position: autonomous (dead reckoning) and GPS* (satellite) navigation. Both navigation methods are used in conjunction with each other.
*: GPS (Global Positioning System)

| Operation | Description |
| Vehicle Position Calculation | The navigation ECU calculates the current vehicle position (direction and current position) using the direction deviation signal from the gyro sensor and driving distance signal calculated from the vehicle speed signal and creates the driving route. |
| Map Display Processing | The navigation ECU processes the vehicle position data, vehicle driving track and map data from the internal memory. |
| Map Matching | The map data from the internal memory is compared to the vehicle position and driving track data. Then, the vehicle position is matched with the nearest road. |
| GPS Correction | The vehicle position is matched to the position measured by the GPS. Then, the GPS measurement position data is compared with the vehicle position and driving track data. If the position is very different, the GPS measurement position is used. |
| Distance Correction | The vehicle speed signal includes errors caused by tire wear and slippage between the tires and road surface. Distance correction is performed to account for this. The navigation ECU automatically offsets the signal to make up for the difference between it and the distance data of the map. The offset is automatically updated. |

Autonomous navigation
This method determines the relative vehicle position based on the driving track determined by the gyro sensor located in the navigation ECU and the vehicle speed signal.
Gyro sensor
Used to calculate the direction by detecting angular velocity. It is located in the navigation ECU.
Vehicle speed signal
Used to calculate the vehicle driving distance.
GPS* navigation (Satellite navigation)
This method detects the absolute vehicle position using radio waves from GPS satellites.
*: GPS satellites were launched by the U.S. Department of Defense for military purposes.

| Number of Satellites | Measurement | Description |
| 2 or less | Measurement is impossible | Vehicle position cannot be obtained because the number of satellites is not enough. |
| 3 | 2-dimensional measurement is possible | Vehicle position is obtained based on the current longitude and latitude. (This is less precise than 3-dimensional measurement.) |
| 4 | 3-dimensional measurement is possible | Vehicle position is obtained based on the current longitude, latitude and altitude. |
Map matching
The current driving route is calculated by autonomous navigation (according to the gyro sensor and vehicle speed signal) and GPS navigation. This information is then compared with possible road shapes from the map data in the internal memory and the vehicle position is set onto the most appropriate road.

| DISC PLAYER OUTLINE |
A disc player uses a laser pickup to read digital signals recorded on a disc. By converting the digital signals to analog, it can play music and audio.
This player can play only audio CDs, CD-Rs (CD-Recordable) and CD-RWs (CD-ReWritable) that have any of the following marks:

The following products may not be playable on your player.
Precautions for use of discs
![]() |
Cleaning
If dirt is on the disc surface, wipe it clean with a soft dry cloth such as an eyeglass cleaner for plastic lenses from the inside to the outside in a radial direction.
| USB AUDIO SYSTEM FUNCTION OUTLINE |
The No. 1 stereo jack adapter assembly is equipped with a USB terminal. Connecting a USB device or "iPod" to the No. 1 stereo jack adapter assembly allows music files to be played. Not only is it possible to play music from a USB device with audio functions, it is also possible to play MP3, WMA or AAC music files that are stored on a USB device. In addition, "iPod" control software is installed, allowing file selection from playlists and operation using shuffle mode.
USB audio system compatible devices
USB device
The following device formats can be used:
| Compatible USB device formats |
|
"iPod"
"iPhone", "iPod", "iPod classic", "iPod nano" and "iPod touch" are trademarks of Apple Inc., registered in the U.S. and other countries.
The following "iPod", "iPod nano", "iPod classic", "iPod touch" and "iPhone" devices can be used with this system.
Made for:
| MP3/WMA/AAC OUTLINE |
Playable MP3 file standards
| Compatible standard | MPEG1 LAYER3, MPEG2 LSF LAYER3 |
| Compatible sampling frequency |
|
| Compatible bit rate |
|
| Compatible channel mode | Stereo, joint stereo, dual channel, monaural |
Playable WMA file standards
| Compatible standard | WMA Ver. 7, 8, and 9 |
| Compatible sampling frequency | 32, 44.1, 48 (kHz) |
| Compatible bit rate (Only compatible with 2-channel playback) |
|
Playable AAC file standards
| Compatible standard | MPEG4/AAC-LC |
| Compatible sampling frequency | 11.025, 12, 16, 22.05, 24, 32, 44.1, 48 (kHz) |
| Compatible bit rate |
|
ID3 tag, WMA tag and AAC tag
Additional text information called an ID3 tag can be input to MP3 files. Information such as song titles and artist names can be stored.
Additional text information called a WMA tag can be input to WMA files. Information such as song titles and artist names can be stored.
Additional text information called an AAC tag can be input to AAC files. Information such as song titles and artist names can be stored.
Usable media
Only CD-ROMs, CD-Rs (CD-Recordable), CD-RWs (CD-ReWritable) and USB devices can be used to play MP3/WMA/AAC files.
Usable media format
Usable media format
| Disc format | CD-ROM Mode 1, CD-ROM XA Mode 2 Form 1 |
| File format | ISO9660 Level 1 and Level 2 (Joliet, Romeo) |
Standards and restrictions
| Maximum directory hierarchy | 8 levels |
| Maximum number of characters for a folder name/file name | 32 characters |
| Maximum number of folders | 192 (Including empty folders, root folders, and folders that do not contain MP3/WMA/AAC files) |
| Maximum number of files in a disc | 255 (Including non- MP3/WMA/AAC files) |
File names
Only files with an extension of ".mp3", ".wma" and ".m4a" can be recognized and played as MP3, WMA or AAC files.
Save MP3, WMA or AAC files with an extension of ".mp3", ".wma" or ".m4a".
| "Bluetooth" OUTLINE |

| *1 | Radio and Display Receiver Assembly (Built-in "Bluetooth" Antenna) | *2 | Navigation ECU (Built-in "Bluetooth" Receiver) |
| *a | Example | *b | Cellular Network |
| *c | Cellular Phone ("Bluetooth" Compatible Type) | *d | Portable Audio Player ("Bluetooth" Compatible Type) |
| *e | "Bluetooth" Wireless Connection | - | - |
"Bluetooth" is a trademark owned by Bluetooth SIG, Inc.
"Bluetooth" is a wireless connection technology that uses the 2.4 GHz frequency band.
Hands-free function
The "Bluetooth" built-in navigation ECU and a "Bluetooth" compatible cellular phone* can be connected using a "Bluetooth" wireless connection. This enables the use of the hands-free function on the cellular phone even if the phone is in a pocket or bag. For this reason, it is not necessary to use a connector or cable to connect the cellular phone.
The hands-free function uses a "Bluetooth" wireless connection. A "Bluetooth" wireless connection can be affected by uncertain elements, such as vehicle location, time of day, etc. Therefore, problems related to establishing connection may be caused temporarily by "Bluetooth" connection conditions. It is necessary to check the frequency of occurrence, connection conditions using another cellular phone, etc. when performing diagnosis.
Compatible hands-free devices
| Required "Bluetooth" specifications | Ver. 2.0 or higher (Ver. 3.0+EDR or higher recommended) |
| Compatible profiles |
|
| Maximum number of hands-free devices that can be registered (including audio devices) | 4 |
"Bluetooth" audio function
The "Bluetooth" built-in navigation ECU and a "Bluetooth" compatible portable audio player* can be connected using a "Bluetooth" wireless connection. This enables files stored in the portable audio player to be heard from the vehicle speakers. In addition, operations such as play/stop can be performed directly from the radio and display receiver assembly.
Compatible "Bluetooth" audio devices
| Required "Bluetooth" specifications | Ver. 2.0 or higher (Ver. 3.0+EDR or higher recommended) |
| Compatible profiles |
|
| Maximum number of audio devices that can be registered (including hands-free devices) | 4 |
| RADIO DESCRIPTION |
Radio frequency band
Radio broadcasts use the radio frequency bands shown in the table below.

Service area
![]() |
The service areas of AM and FM broadcasts are vastly different. Sometimes an AM broadcast can be received very clearly but an FM stereo broadcast cannot. FM stereo has the smallest service area, and is prone to pick up static and other types of interference such as noise.
| *a | FM (Stereo) |
| *b | FM (Monaural) |
| *c | AM |
Radio reception problems
![]() |
Phasing
AM broadcasts are susceptible to electrical interference and another kind of interference called phasing. Occurring only at night, phasing is the interference created when a vehicle receives 2 radio wave signals from the same transmitter. One signal is reflected off the ionosphere and the other signal is received directly from the transmitter.
| *a | Phasing |
| *b | Ionosphere |
![]() |
Multipath
Multipath is a type of interference created when a vehicle receives 2 radio wave signals from the same transmitter. One signal is reflected off buildings or mountains and the other signal is received directly from the transmitter.
| *a | Multipath |
![]() |
Fade out
Fade out is caused by objects (buildings, mountains and other large obstructions) that deflect part of a signal, resulting in a weaker signal when the object is between the transmitter and vehicle. High frequency radio waves, such as FM broadcasts, are easily deflected by obstructions. Low frequency radio waves, such as AM broadcasts, are less likely to be deflected.
| *a | Fade Out |
Noise problem
Technicians must have a clear understanding about each customer's noise complaint. Use the following table to diagnose noise problems.
| Radio Frequency | Noise Occurrence Condition | Presumable Cause |
| AM | Noise occurs in a specific area | Foreign noise |
| Noise occurs when listening to an intermittent broadcast | An identical program transmitted from multiple towers can cause noise where the signals overlap | |
| Noise occurs only at night | Signal phasing | |
| FM | Noise occurs while driving in a specific area | Multipath resulting from a change in FM frequency |
| NAVIGATION ECU OUTLINE |
The navigation ECU resides in the vehicle. Inputs to the system are sent from the radio and display receiver assembly using LVDS communication, the GPS receiver through which the vehicle location is obtained, and connectivity via a "Bluetooth" enabled phone. The navigation ECU enables the use of exclusive applications.
| VEHICLE CUSTOMIZATION OUTLINE |
Customization of functions can also be customized on the multi-display screen. Refer to Owner's Manual for further information on customizable items for the navigation system.
| "MirrorLink" FUNCTION OUTLINE (w/ "MirrorLink" Function) |
"MirrorLink" is a function that enables the radio and display receiver assembly to operate applications on a smartphone which meets Car Connectivity Consortium standards by connecting the smartphone to the radio and display receiver assembly with a USB cable.
Smartphones which passed the CCC (Car Connectivity Consortium) MirrorLink 1.1 certification program.
For details, refer to http://carconnectivity.org/ and http://www.mirrorlink.com/.
Contact the smartphone manufacturer or service provider for details about MirrorLink compatibility. The confirmation method and release schedule varies depending on the smartphone.
| CONNECTED SERVICES OUTLINE (w/ Connected Services) |
The following services are available by connecting the navigation system to Toyota's portal site via the internet using a cellular phone.
| TRAFFIC AND PARKING INFORMATION FUNCTION OUTLINE (w/ Connected Services) |
Traffic information, traffic prediction information and parking lot information can be viewed.
There are 2 methods to receive the above information.
| Priority | Method | Information |
| 1st | Internet by using a cellular phone |
|
| 2nd | FM | RDS-TMC (Radio Data System-Traffic Message Channel) |
| MOBILE ASSISTANT FUNCTION OUTLINE |
This function can be used when a compatible smartphone with an appropriate speech recognition application is connected to the radio and display receiver assembly via "Bluetooth".
| "Wi-Fi" OUTLINE |
"Wi-Fi" is a worldwide wireless communication standard widely used as a short range communication tool.
"Wi-Fi" is a trademark owned by Wi-Fi Alliance, a non-profit industry association.
The radio receiver assembly uses the 2.4 GHz frequency band for "Wi-Fi" communication.
| AUTOMATIC SOUND LEVELIZER (ASL) FUNCTION OUTLINE |
The Automatic Sound Levelizer (ASL) function automatically adjusts the audio system volume level in order to compensate for increased vehicle noise (vehicle noise tends to increase as vehicle speed increases). The ASL adjusts the volume level based upon vehicle speed signals sent from the combination meter assembly.
| COMMUNICATION SYSTEM |
AVC-LAN Outline

Components of the navigation system communicate with each other via the AVC-LAN.
The AVC-LAN uses a twisted pair of wires for its communication lines.
The master unit of the AVC-LAN is the radio and display receiver assembly.
Local Bus Communication Outline

Components of the navigation system communicate with each other via the local bus.
The local bus uses a twisted pair of wires for its communication lines.
The master unit of the local bus is the radio and display receiver assembly.
LVDS Communication Outline
The navigation system uses LVDS communication between the radio and display receiver assembly and navigation ECU.
If a short or open occurs in the LVDS communication line, communication is interrupted and the system will not operate normally.
CAN Communication Outline
The navigation system uses CAN communication between the radio and display receiver assembly and ECUs.
| DIAGNOSTIC FUNCTION OUTLINE |
The navigation system has a diagnostic function.