NAVIGATION SYSTEM (for Radio and Display Type) > OPERATION CHECK |
| CHECK NAVIGATION SYSTEM NORMAL CONDITION |
If the symptom is applicable to any of the following, it is intended behavior, and not a malfunction.
| Symptom | Answer |
| A longer route than expected is chosen. | Depending on the road conditions, the navigation ECU may determine that a longer route is quicker. |
| Even when distance priority is high, the shortest route is not shown. | Some routes may not be advised due to safety concerns. |
| When the vehicle is put into motion immediately after the engine starts, the navigation system deviates from the correct position. | If the vehicle starts before the navigation system activates, the system may not react. |
| When driving on certain types of roads, especially new roads, the vehicle position deviates from the correct position. | When the vehicle is driving on new roads not available on the internal memory, the system attempts to match it to another nearby road, causing the position mark to deviate. |
| Expected arrival time is earlier than current time, or time different from expected arrival time is displayed. | If a destination is set to a point where a different time zone is used, the system displays an expected arrival time corresponding to the time zone of the destination. If a location on the sea is set as the destination, the system may display an expected arrival time corresponding to the time zone setting of the vehicle. Check which communication is not used for displaying traffic information. |
![]() |
The following symptoms are not malfunctions, but are caused by errors inherent in the GPS, gyro sensor or navigation ECU.
The current position mark may be displayed on a nearby parallel road.
![]() |
Immediately after a fork in the road, the current vehicle position mark may be displayed on the wrong road.
![]() |
When the vehicle turns right or left at an intersection, the current vehicle position mark may be displayed on a nearby parallel road.
![]() |
When the vehicle is carried, such as on a ferry, and the vehicle itself is not driving, the current vehicle position mark may be displayed in the position where the vehicle was until a measurement can be performed by the GPS.
![]() |
When the vehicle travels on a steep hill, the current vehicle position mark may deviate from the correct position.
![]() |
When the vehicle makes a continuous turn (e.g. 360, 720, 1080 degrees), the current vehicle position mark may deviate from the correct position.
![]() |
When the vehicle moves erratically, such as constant lane changes, the current vehicle position mark may deviate from the correct position.
![]() |
When the ignition switch is turned to ACC or ON and the vehicle is turned on a turntable before parking, the current vehicle position mark may not indicate the correct direction. The same will occur when the vehicle comes out of the parking garage.
![]() |
When the vehicle travels on a snowy road or a mountain path with tire chains installed or using a spare tire, the current vehicle position mark may deviate from the correct position.
![]() |
When the tires are changed, the current vehicle position mark may deviate from the correct position.
| CHECK PANEL & STEERING SWITCH |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "Panel & Steering Switch" from the "Function Check/Setting I" screen.
![]() |
Panel & Steering Switch Check Mode
| Display | Content |
| *a: Switch condition | "Pushed" is displayed when any switch is pushed |
| *b: Number of switches pushed |
|
| *c: Rotary switch direction | Direction of rotary switch is displayed |
Operate each switch and check that the switch conditions are correctly displayed.
| CHECK TOUCH SWITCH |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "Touch Switch" from the "Function Check/Setting I" screen.
![]() |
Touch Switch Check
Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.
| CHECK VEHICLE SIGNAL |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "Vehicle Signal" from the "Function Check/Setting I" screen.
![]() |
Vehicle Signal Check Mode
| Display | Content |
| Battery | Battery voltage is displayed. |
| IG | Ignition switch ON/OFF state is displayed. |
| PKB | Parking brake ON/OFF state is displayed. |
| REV | Reverse signal ON/OFF state is displayed. |
| SPEED | Vehicle speed is displayed in km/h. |
| TAIL | Tail signal (light control switch) ON/OFF state is displayed. |
| ADIM/TCAN | Brightness state DIM (with)/BRIGHT (without) is displayed. |
When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.
| CHECK MICROPHONE |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "Next Page" from the "Function Check/Setting I" screen.
![]() |
Select "EXT BOX" from the "Function Check/Setting II" screen.
![]() |
Select "Microphone Check" from the "EXT BOX" screen.
![]() |
Microphone Check
| Display | Content |
| *a: Microphone input level meter | Monitors the microphone input level every 0.1 seconds and displays the results in 8 different levels. |
When speaking into the microphone, check that the microphone input level meter changes according to the input level.
| CHECK SYSTEM SENSORS |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "Next Page" from the "Function Check/Setting I" screen.
![]() |
Select "EXT BOX" from the "Function Check/Setting II" screen.
![]() |
Select "System Sensors Check" from the "EXT BOX" screen.
![]() |
System Sensors Check
| Display | Content | ||
| Reception number | Displays reception condition of the satellites used to determine vehicle position. | Blue: P (In use) | System is using GPS signal for location. |
| Yellow: T (Receiving) | System is tracking GPS signal for location. | ||
| No color: Not in use | System cannot receive GPS signal (searching for GPS signal). | ||
| Status | Displays reception status of the satellites used to determine vehicle position. | OK(H3D) | High accuracy 3-dimensional location method is being used. |
| OK(H2D) | High accuracy 2-dimensional location method is being used. | ||
| OK(3D) | 3-dimensional location method is being used. | ||
| OK(2D) | 2-dimensional location method is being used. | ||
| NG | Location data cannot be used. | ||
| error | Reception error has occurred. | ||
| - | Any other state. | ||
| Measurement ratio | Displays the ratio of satellites performing measurements. | 3D | The ratio of satellites performing 3D positioning, Hyper 3D positioning and Hyper 2D positioning is displayed. |
| 2D | The ratio of satellites performing 2D positioning is displayed. | ||
| NG | The ratio of satellites not performing measurement is displayed. | ||
| Date | Date/time information obtained from GPS signals is displayed in Greenwich Mean Time (GMT). | ||
| Position | Latitude and longitude information on current position is displayed. | ||
| Display | Content |
| Pulse Count | Displays the accumulated number of input pulses beginning when this screen is displayed. |
| Speed | Displays vehicle speed. |
| Display | Content | Content |
| Gyro Voltage | Displays the output voltage of the gyro sensor. | - |
| 0 point Voltage | Displays the zero-point voltage of the gyro sensor. | - |
| Relative bearing | Displays the output angle of the gyro sensor. | The amount of change in bearing angle (degrees) after the system sensor check screen is displayed (clockwise: "+", counterclockwise: "-"). |
| Display | Content |
| Gyro/Distance correction study situation | Displays learning status of Gyro/Distance correction. |
| Display | Content |
| Reset | When this switch is pressed and held for 3 seconds or more, the values for the display items of SPD and Sensor Signal are reset and display "0". |
When the "System Sensors Check" screen is displayed, check all the sensor signals.
| CHECK SPEAKER |
Turn audio mode on and play any audio source.
Enter diagnostic mode (Click here).
![]() |
Select "Failure Diagnosis" from the "Service Menu" screen.
![]() |
Select "System Check" from the "Failure Diagnosis" screen.
![]() |
Select "SP Check ON" from the "System Check Mode" screen.
Check the speaker wiring and check that the speakers are functioning properly.
Sound stops when any of the following conditions are met:
"SP Check OFF" is selected.
The ignition switch is turned off.
Diagnostic mode is turned off.
The screen is changed to another screen.
Audio mode is turned off.
| CHECK SOFTWARE ERROR HISTORY |
Check Software Error History.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Navigation System / Utility / Software Error History.
When an item is stored for Software Error History, record it before repairing the multi-media module receiver assembly.
| Error Description | Trigger | Detail |
| Software Reset | Navi Microcomputer | Hexadecimal Number |
| Audio Microcomputer | ||
| CAN Microcomputer | ||
| No Video Signal | Front Monitor | |
| Rear Monitor | ||
| MOST Cold Restart | Always |
Clear Software Error History.
When DTCs are cleared using any of the following operations, Software Error History will be cleared as well (Click here).
| CHECK OPTICAL DISC ERROR HISTORY |
Check Optical Disc Error History.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Navigation System / Utility / Optical Disc Error History.
When an item is stored for Optical Disc Error History, record it before proceeding with troubleshooting.
| Display | Content |
| Error Type | Displays the type of error. |
| Device | Displays the malfunctioning device. |
| Date | Displays the date and time that the malfunction occurred. |
| Error Type | Detection Condition | Action |
| Read Error | When a disc read error occurs. | Proceed to next suspected area shown in Problem Symptoms Table (Click here) |
| Disc damaged/upside down/dirty | When it is determined that any of the following is the cause of the disc read error:
| |
| Cannot determine disc type | An unsuitable disc is inserted. | |
| DPS error | When an error occurs while decoding MP3/WMA/AAC files. | |
| Some files are corrupt |
| |
| Some files cannot be found |
| |
| Copy protection violation | When a file with copyright protection that cannot be played back is played back. |
| Device | Component |
| DVD-P | Not available |
| CD-P | Radio and display receiver assembly |
| R-Seat DVD-P | Not available |
Clear Optical Disc Error History.
When DTCs are cleared using any of the following operations, Optical Disc Error History will be cleared as well (Click here).
| CHECK VIDEO DEVICE CONNECTION CHECK |
Check Video Device Connection Check.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Navigation System / Utility / Video Device Connection Check.
When an item is stored for Video Device Connection Check, record it before proceeding with troubleshooting.
| Error Detected Image Line (Type) | Areas to be Checked |
| H/U - > Separate Display (GVIF) | Not available |
| H/U - > Full RSE (GVIF) | Not available |
| RSE - > Seat Back Display RH (GVIF) | Not available |
| RSE - > Seat Back Display LH (GVIF) | Not available |
| Rear Camera - > H/U (NTSC) | NTSC video signal between the radio and display receiver assembly and rear television camera assembly |
| IPA/BGM/PVM ECU - > Separate Display (GVIF) | Not available |
| IPA/BGM/PVM ECU - > H/U (NTSC) | Not available |
| IPA/BGM/PVM ECU - > H/U (GVIF) | Not available |
Clear Video Device Connection Check.
When DTCs are cleared using any of the following operations, Video Device Connection Check will be cleared as well (Click here).
| CHECK "Wi-Fi" CONNECTION HISTORY |
Check "Wi-Fi" Connection History.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Navigation System / Utility / "Wi-Fi" Connection History.
When a value for an item is displayed in "Wi-Fi" Connection History, record it before proceeding with troubleshooting.
| Item | Content |
| Occurrence Date/Time | Year is displayed in 4 digits and month, date, hour, minute and second are displayed in 2 digits |
| Result | Connect/Disconnect Success |
| Timeout | |
| Communication Error | |
| Authentication Failure | |
| Disconnection Failure | |
| Other Failure | |
| Contents | No Error |
| AP Connection Error | |
| AP Connection Error (WPS) | |
| DHCP Connection Error | |
| DNS Connection Error | |
| HTTP Connection Error | |
| Other Error | |
| Destination MAC Address | Displayed in lower case hexadecimal format with "-" inserted every two characters. |
| Destination SSID | Data is displayed as ASCII code |
| WLAN Standard | 802.11 b |
| 802.11 g | |
| 802.11 n | |
| Undetectability | |
| Received Signal Strength | -127 dBm to +127 dBm |
| Data Rate | 1.0 Mbps |
| 2.0 Mbps | |
| 5.5 Mbps | |
| 6.0 Mbps | |
| 6.5 Mbps | |
| 9.0 Mbps | |
| 11.0 Mbps | |
| 12.0 Mbps | |
| 13.0 Mbps | |
| 18.0 Mbps | |
| 19.5 Mbps | |
| 24.0 Mbps | |
| 26.0 Mbps | |
| 36.0 Mbps | |
| 39.0 Mbps | |
| 48.0 Mbps | |
| 52.0 Mbps | |
| 54.0 Mbps | |
| 58.5 Mbps | |
| 65.0 Mbps | |
| Undetectability | |
| Packet Error Rate | Displayed in decimal format with "%" |
Clear "Wi-Fi" connection history.
When DTCs are cleared using any of the following operations, "Wi-Fi" Connection History will be cleared as well (Click here).