DTC P160300 Engine Stall History |
| DTC No. | DTC Detection Condition |
| P160300 | After monitoring for startability problems (P160400) finishes and 5 seconds or more have elapsed after starting the engine, with the engine running, the engine stops (the engine speed drops to 200 rpm or less) without the engine switch being operated for 0.5 seconds or more (1 trip detection logic). |
| Trouble Area | |
| Ignition system |
|
| Fuel system |
|
| Intake and exhaust systems |
|
| Other control systems |
|
| Engine |
|
| High load from another system |
|
| Symptom | Suspected Area |
| Engine vibration occurs and engine stops |
|
| Engine stops with no engine vibration | Ignition system, injection stoppage, high load from external parts |
| Engine can be started with accelerator pedal depressed | Insufficient air volume |
| Engine stalls or is difficult to start immediately after engine stalled, regardless of whether engine is cold or warm | Deposits in intake system or combustion chamber caught temporarily on intake or exhaust valve |
| 1.CHECK FOR ANY OTHER DTCS OUTPUT |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| Only DTC P160300 is output | A |
| DTCs other than P160300 are output | B |
|
| ||||
| A | |
| 2.READ FREEZE FRAME DATA (ISC F/B LEARN TORQUE) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P160300 | Result | Suspected Area | Action | Proceed to |
| ISC F/B Learn Torque | Less than 15 Nm | - | Go to the next step | A |
| 15 Nm or higher | Throttle body with motor assembly | Go to ENGINE STALLS (from step 11) | B |
|
| ||||
| A | |
| 3.READ FREEZE FRAME DATA (A/F (O2) SENSOR VOLTAGE B1S1, SHORT FT BANK 1 AND LONG FT BANK 1) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P160300 | Suspected Area | Action | Proceed to | ||
| A/F (O2) Sensor Voltage B1S1 | Short FT Bank 1 | Long FT Bank 1 | |||
| 2.8 V to 3.8 V | -15% to 15% | -15% to 15% | - | Go to the next step | A |
| 3.8 V or higher | 15% or higher | - | Fuel pump | Go to ENGINE STALLS (from step 22) | B |
| Less than 2.8 V, or 3.8 V or higher | Less than -15%, or 15% or higher | Less than -15%, or 15% or higher |
| Go to ENGINE STALLS (from step 16)* | |
|
| ||||
| A | |
| 4.READ FREEZE FRAME DATA (CALCULATE LOAD) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P160300 | Result | Suspected Area | Action | Proceed to |
| Calculate Load | +10% or higher of the normal value of the vehicle | EGR valve assembly | Go to ENGINE STALLS (from step 15) | NEXT |
| Less than 10% of the normal value of the vehicle | - | Go to ENGINE STALLS |
| NEXT | ||
| ||