ENGINE UNIT > INSPECTION |
| 1. INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
![]() |
Turn the roller by hand to check that it turns smoothly.
| 2. INSPECT VALVE LASH ADJUSTER ASSEMBLY |
Place the valve lash adjuster assembly into a container filled with engine oil.

| *a | Correct | *b | Incorrect |
| *c | Taper | *d | Low Pressure Chamber |
| *e | High Pressure Chamber | *f | Plunger |
| *g | Check Ball | - | - |
Insert the tip of SST into the valve lash adjuster assembly plunger and use the tip to press down on the check ball inside the plunger.
Squeeze SST and the valve lash adjuster assembly together to move the plunger up and down 5 to 6 times.
Check the movement of the plunger and bleed the air.
After bleeding the air, remove SST. Then try to quickly and firmly press the plunger by hand.
| 3. INSPECT CAMSHAFT OIL CLEARANCE |
Clean the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, No. 3 camshaft bearing cap, No. 4 camshaft bearing cap, camshaft housing sub-assembly and camshaft journals.
Place the camshaft and No. 2 camshaft on the camshaft housing sub-assembly.
![]() |
Lay a strip of Plastigage across each of the camshaft journals.
| *a | Plastigage |
Install the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, No. 3 camshaft bearing cap and No. 4 camshaft bearing cap .
Install the camshaft housing sub-assembly .
Remove the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, No. 3 camshaft bearing cap and No. 4 camshaft bearing cap .
![]() |
Measure the Plastigage at its widest point.
| *a | Plastigage |
| *b | No. 1 Journal |
| *c | Other Journal |
| Item | Specified Condition |
| Intake No. 1 journal | 0.035 to 0.072 mm (0.00138 to 0.00283 in.) |
| Exhaust No. 1 journal | 0.049 to 0.086 mm (0.00193 to 0.00339 in.) |
| Other journals | 0.025 to 0.062 mm (0.000984 to 0.00244 in.) |
| Item | Specified Condition |
| Intake No. 1 journal | 0.085 mm (0.00335 in.) |
| Exhaust No. 1 journal | 0.095 mm (0.00374 in.) |
| Other journals | 0.085 mm (0.00335 in.) |
| 4. INSPECT CAMSHAFT THRUST CLEARANCE |
Clean the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, No. 3 camshaft bearing cap, No. 4 camshaft bearing cap, camshaft housing sub-assembly and camshaft journals.
Place the camshaft and No. 2 camshaft on the camshaft housing sub-assembly.
Install the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, No. 3 camshaft bearing cap and No. 4 camshaft bearing cap .
Install the camshaft housing sub-assembly .
![]() |
Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.
| Item | Specified Condition |
| Intake | 0.060 to 0.155 mm (0.00236 to 0.00610 in.) |
| Exhaust | 0.060 to 0.155 mm (0.00236 to 0.00610 in.) |
| Item | Specified Condition |
| Intake | 0.170 mm (0.00669 in.) |
| Exhaust | 0.170 mm (0.00669 in.) |
| 5. INSPECT CAMSHAFT |
![]() |
Inspect the camshaft for runout.
Place the camshaft on V-blocks.
Using a dial indicator, measure the runout at the center journal.
![]() |
Inspect the cam lobes (for intake valve).
Using a micrometer, measure the cam lobe height.
![]() |
Inspect the cam lobes (for fuel pump drive).
Using a micrometer, measure the cam lobe height.
Inspect the camshaft journals.
Using a micrometer, measure the journal diameter.
| Item | Specified Condition |
| No. 1 journal | 34.449 to 34.465 mm (1.35626 to 1.35689 in.) |
| Other journals | 22.959 to 22.975 mm (0.90390 to 0.90453 in.) |
| 6. INSPECT NO. 2 CAMSHAFT |
![]() |
Inspect the No. 2 camshaft for runout.
Place the No. 2 camshaft on V-blocks.
Using a dial indicator, measure the runout at the center journal.
![]() |
Inspect the cam lobes.
Using a micrometer, measure the cam lobe height.
Inspect the camshaft journals.
Using a micrometer, measure the journal diameter.
| Item | Specified Condition |
| No. 1 journal | 34.449 to 34.465 mm (1.35626 to 1.35689 in.) |
| Other journals | 22.959 to 22.975 mm (0.90390 to 0.90453 in.) |
| 7. INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY |
Install the camshaft timing exhaust gear assembly to the No. 2 camshaft .
![]() |
Release the lock pin.
| *a | Knock Pin |
| *b | Advance Side Path |
| *c | Retard Side Path |
| *d | Open |
| *e | Close |
![]() | Rubber Piece |
![]() | Vinyl Tape |
Clean the camshaft journal with non-residue solvent.
Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.
Make a hole in the vinyl tape placed on the advance side path. Make a hole in the vinyl tape placed on the retard side path on the opposite side to that of the advance side path as shown in the illustration.
![]() |
Apply approximately 200 kPa (2.0 kgf/cm2, 29 psi) of air pressure to the 2 open paths (the advance side path and retard side path).
| *a | Advance Side Path |
| *b | Retard Side Path |
![]() |
Check that the camshaft timing exhaust gear assembly turns in the retard direction when reducing the air pressure applied to the advance side path.
| *a | Advance Side Path |
| *b | Retard Side Path |
| *c | Hold Pressure |
| *d | Decompress |
When the camshaft timing exhaust gear assembly moves to the most retarded position, release the air pressure from the advance side path, and then from the retard side path.
Check for smooth rotation.
Turn the camshaft timing exhaust gear assembly within its movable range (26.5 to 28.5°) 2 or 3 times, but do not turn it to the most advanced position. Make sure that the camshaft timing exhaust gear assembly turns smoothly.
Check the lock at the most advanced position.
Make sure that the camshaft timing exhaust gear assembly locks at the most advanced position.
Remove the vinyl tape and rubber pieces from the No. 2 camshaft.
Remove the bolt and camshaft timing exhaust gear assembly from the No. 2 camshaft.
| 8. INSPECT CHAIN SUB-ASSEMBLY |
![]() |
Using a spring scale, pull the chain sub-assembly with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.
| *a | Measurement Length |
Using a vernier caliper, measure the length of 15 pins.
| 9. INSPECT CRANKSHAFT TIMING SPROCKET |
![]() |
Place the chain sub-assembly around the crankshaft timing sprocket.
Using a vernier caliper, measure the crankshaft timing sprocket diameter with the chain sub-assembly.
| 10. INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY |
![]() |
Move the stopper plate counterclockwise to release the lock. Push the plunger and check that it moves smoothly.
| *a | Plunger |
| *b | Stopper Plate |
| 11. INSPECT CHAIN TENSIONER SLIPPER |
![]() |
Measure the wear depth of the chain tensioner slipper.
| *a | Depth |
| 12. INSPECT NO. 1 CHAIN VIBRATION DAMPER |
![]() |
Measure the wear depth of the No. 1 chain vibration damper.
| *a | Depth |
| 13. INSPECT TIMING CHAIN GUIDE |
![]() |
Measure the wear depth of the timing chain guide.
| *a | Depth |
| 14. INSPECT NO. 1 BALANCE SHAFT THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance while moving the No. 1 balance shaft back and forth.
| 15. INSPECT NO. 2 BALANCE SHAFT THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance while moving the No. 2 balance shaft back and forth.
| 16. INSPECT BALANCE SHAFT BACKLASH |
![]() |
Secure the No. 2 balance shaft in place, and then using a dial indicator, measure the backlash of the No. 1 balance shaft and No. 2 balance shaft as shown in the illustration.
| *a | Secure |
| 17. INSPECT CYLINDER HEAD SET BOLT |
![]() |
Using a vernier caliper, measure the diameter of the threads at the measurement point.
| *a | Measurement Point |
| 18. INSPECT EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: Front Catalyst) |
![]() |
Using a precision straightedge and feeler gauge, measure the warpage of the surface that contacts the cylinder head sub-assembly.