Home › Engine / Hybrid System ยท 6AR-FSE › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > REMOVAL

for Preparation Click here



1. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE


    A337909
  1. Remove the engine oil level dipstick.

  1. Remove the bolt and engine oil level dipstick guide.

  1. Remove the O-ring from the engine oil level dipstick guide.



2. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    A209579
  1. Remove the 4 bolts and No. 1 exhaust manifold heat insulator from the exhaust manifold converter sub-assembly (TWC: Front Catalyst).



3. REMOVE EGR PIPE CONNECTOR


    A339007
  1. Remove the 4 bolts, nut and EGR pipe connector from the exhaust manifold converter sub-assembly (TWC: Front Catalyst), EGR cooler assembly and cylinder block sub-assembly.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut



    A338734
  1. Remove the 2 EGR cooler gaskets from the EGR pipe connector.



4. REMOVE MANIFOLD STAY


    A338738
  1. Remove the bolt, nut and manifold stay from the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and stiffening crankcase assembly.



5. REMOVE NO. 2 MANIFOLD STAY


    A338737
  1. Remove the bolt, nut and No. 2 manifold stay from the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and stiffening crankcase assembly.



6. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: Front Catalyst)


    A195979
  1. Remove the 5 nuts and exhaust manifold converter sub-assembly (TWC: Front Catalyst) from the cylinder head sub-assembly.



    A195981
  1. Remove the exhaust manifold gasket from the cylinder head sub-assembly.



7. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET


    A210230
  1. Remove the 4 bolts and No. 1 compressor mounting bracket.



8. REMOVE FUEL PUMP PROTECTOR


    A337351
  1. Remove the 2 bolts and fuel pump protector from the cylinder head cover sub-assembly.



9. DISCONNECT FUEL TUBE SUB-ASSEMBLY (for Direct Injection)

NOTICE:
Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.



  1. Disconnect the fuel tube sub-assembly from the No. 1 fuel pipe.



      A303154E04
    1. Pull off the fuel tube connector cover.
      Text in Illustration 
      *a
      Fuel Tube Connector Cover
      V100135
      Pull off



    2. A337354E01
    3. Pinch the retainer of the fuel tube connector, and then pull the fuel tube connector off of the fuel pipe.
      Text in Illustration 
      *a
      Retainer
      *b
      Fuel Tube Connector
      *c
      Nylon Tube
      *d
      O-ring
      *e
      Fuel Pipe
      V100135
      Pinch
      V100136
      Pull

      NOTICE:
      Be sure to disconnect the fuel tube connector by hand.

    4. If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

      NOTICE:
      1. Be sure to disconnect the fuel tube connector by hand.
      1. Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).
      1. Do not bend, twist, pinch or kink the nylon tube.

    5. Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.

    6. Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



10. REMOVE NO. 1 FUEL PIPE


    A337374
  1. Remove the No. 1 fuel pipe and gasket from the fuel pump with seal sub-assembly.



11. REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY


    A337375
  1. Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.



    A337377
  1. Loosen the 2 bolts of the fuel pump with seal sub- assembly.

  1. Remove the No. 1 fuel pipe sub-assembly from the fuel delivery pipe sub-assembly and fuel pump with seal sub- assembly.



12. REMOVE FUEL PUMP WITH SEAL SUB-ASSEMBLY


    A339043
  1. Disconnect the fuel pump with seal sub-assembly connector.

  1. Remove the 2 bolts and fuel pump with seal sub- assembly from the cylinder head cover sub- assembly.



    A337332E01
  1. Remove the fuel pump lifter guide, fuel pump lifter assembly and fuel pump insulator from the fuel pump with seal sub-assembly.
    Text in Illustration 
    *1
    Fuel Pump with Seal Sub-assembly
    *2
    Fuel Pump Insulator
    *3
    Fuel Pump Lifter Assembly
    *4
    Fuel Pump Lifter Guide



    A337333
  1. Remove the O-ring from the fuel pump sub- assembly.



    A338469E01
  1. Remove the fuel pump spacer gasket from the cylinder head cover sub-assembly.
    Text in Illustration 
    *1
    Fuel Pump Spacer Gasket
    *2
    O-ring

  1. Remove the 2 O-rings from the No. 4 camshaft bearing cap.



13. DISCONNECT FUEL TUBE SUB-ASSEMBLY (for Port Injection)

NOTICE:
Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.



  1. Disconnect the fuel tube sub-assembly from the fuel delivery pipe.



      A303154E03
    1. Pull off the fuel tube connector cover.
      Text in Illustration 
      *a
      Fuel Tube Connector Cover
      V100135
      Pull off



    2. A337356E01
    3. Pinch the retainer of the fuel tube connector, and then pull the fuel tube connector off of the fuel pipe.
      Text in Illustration 
      *a
      Retainer
      *b
      Fuel Tube Connector
      *c
      Nylon Tube
      *d
      O-ring
      *e
      Fuel Pipe
      V100135
      Pinch
      V100136
      Pull

      NOTICE:
      Be sure to disconnect the fuel tube connector by hand.

    4. If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

      NOTICE:
      1. Be sure to disconnect the fuel tube connector by hand.
      1. Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).
      1. Do not bend, twist, pinch or kink the nylon tube.

    5. Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.

    6. Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



14. REMOVE FUEL DELIVERY PIPE


    A337363
  1. Remove the 2 bolts and fuel delivery pipe with the port fuel injector assemblies.

    NOTICE:
    Be careful not to drop the port fuel injector assemblies when removing the fuel delivery pipe.



15. REMOVE FUEL DELIVERY SPACER


    A337364
  1. Remove the 2 fuel delivery spacers from the cylinder head sub-assembly.



16. REMOVE INJECTOR VIBRATION INSULATOR


    A337365
  1. Remove the 4 injector vibration insulators from the cylinder head sub-assembly.



17. REMOVE PORT FUEL INJECTOR ASSEMBLY


    A337366
  1. Pull the 4 port fuel injector assemblies out of the fuel delivery pipe.

  1. Remove the O-ring from each port fuel injector assembly.

  1. Attach a tag or label with the corresponding cylinder number to each port fuel injector assembly so that they can be installed to their original locations.

    NOTICE:
    Cover the port fuel injector assemblies with plastic bags to prevent damage and contamination.



18. REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY


    A337998
  1. Disconnect the throttle body with motor assembly connector.

  1. Remove the 4 bolts and throttle body with motor assembly from the intake manifold.

    NOTICE:
    If the throttle body with motor assembly has been struck or dropped, replace it.



    A337999E01
  1. Slide the 2 clips and disconnect the No. 2 water by-pass hose and No. 3 water by-pass hose from the throttle body with motor assembly.
    Text in Illustration 
    *1
    No. 2 Water By-pass Hose
    *2
    No. 3 Water By-pass Hose



19. REMOVE THROTTLE BODY GASKET


    A338000
  1. Remove the throttle body gasket from the intake manifold.



20. DISCONNECT NO. 2 VENTILATION HOSE


    A338746
  1. Slide the clip and disconnect the No. 2 ventilation hose from the PCV valve (ventilation valve sub-assembly).



21. REMOVE NO. 2 EGR PIPE


    A338724
  1. Disengage the 2 wire harness clamps from the No. 2 EGR pipe.



    A338725
  1. Remove the 4 bolts and No. 2 EGR pipe from the EGR valve assembly and intake manifold.



    A338726
  1. Remove the No. 2 EGR pipe gasket from the EGR valve assembly.



    A338727
  1. Remove the EGR inlet gasket from the intake manifold.



22. REMOVE INTAKE MANIFOLD


    A338730
  1. Remove the 6 bolts and intake manifold from the cylinder head sub-assembly.



    A338731
  1. Remove the manifold gasket from the intake manifold.



23. REMOVE NO. 5 ENGINE WIRE


    A338550
  1. Remove the 2 bolts and disconnect the No. 5 engine wire from the fuel delivery pipe sub-assembly.

  1. Disconnect the fuel pressure sensor connector, knock control sensor connector and 4 fuel injector set connectors.

  1. Disengage the 2 clamps and remove the No. 5 engine wire.



24. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY


    A337371
  1. Remove the 3 bolts, 2 nuts and fuel delivery pipe sub-assembly with the direct fuel injector assemblies.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut

    NOTICE:
    1. Make sure not to touch or strike the tips of the direct fuel injector assemblies.
    1. Pull and remove the fuel delivery pipe sub-assembly in a straight line without tilting it.



25. REMOVE DIRECT FUEL INJECTOR ASSEMBLY


    A335649E01
  1. Secure the fuel delivery pipe sub-assembly in a vise between aluminum plates and pull out the 4 direct fuel injector assemblies.

    NOTICE:
    1. Pull and remove each direct fuel injector assembly in a straight line to avoid damaging the seal surface of the fuel delivery pipe sub-assembly O-ring.
    1. Attach a tag or label with the corresponding cylinder number to each direct fuel injector assembly so that they can be installed to their original locations.

  1. Remove the nozzle holder clamp from each direct fuel injector assembly.

  1. Using needle nose pliers, remove the No. 3 fuel injector back-up ring from each direct fuel injector assembly.

  1. Remove the O-ring and No. 1 fuel injector back-up ring from each direct fuel injector assembly.

  1. Remove the C-ring and injector vibration insulator from each direct fuel injector assembly.



26. REMOVE FUEL INJECTOR SEAL


    A273082
  1. Using the tip of needle nose pliers, pinch and pull the fuel injector seal at several points to stretch it.

    NOTICE:
    1. Excessively pinching the fuel injector seal may damage the groove of the direct fuel injector assembly.
    1. If a direct fuel injector assembly is dropped or the tip of a direct fuel injector assembly is struck, replace it with a new one.

  1. Remove the fuel injector seal from each direct fuel injector assembly.



27. REMOVE EGR VALVE WITH COOLER ASSEMBLY


    A338753
  1. Disconnect the EGR valve assembly connector.



    A340959
  1. Remove the engine cover joint and separate the fuel hose bracket from the EGR valve bracket.



    A340960
  1. Remove the 4 bolts and 2 EGR valve brackets.



    A338985
  1. Disengage the water hose from the hose clamp.



    A338756
  1. Slide the clip and disconnect the water hose sub-assembly from the EGR cooler assembly.



    A338757E01
  1. Slide the clip and disconnect the No. 2 water by-pass hose from the EGR valve assembly.
    Text in Illustration 
    *1
    No. 2 Water By-pass Hose
    *2
    No. 3 Water By-pass Hose
    *3
    No. 4 Water By-pass Hose

  1. Slide the clip and disconnect the No. 3 water by-pass hose from the EGR cooler assembly.

  1. Slide the clip and disconnect the No. 4 water by-pass hose from the EGR cooler assembly.



    A338758
  1. Remove the 2 nuts and EGR valve with cooler assembly from cylinder head sub-assembly.



    A338759
  1. Remove the No. 2 EGR pipe gasket from the EGR valve assembly.



28. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    A337915
  1. Remove the dust cover from the V-ribbed belt tensioner assembly.



    A337916
  1. Remove the bolt and V-ribbed belt tensioner assembly from the water inlet housing.



29. REMOVE NO. 1 WATER BY-PASS PIPE


    A337910
  1. Remove the bolt, 2 nuts and No. 1 water by-pass pipe and gasket.
    Text in Illustration 
    V100135
    Nut
    V100136
    Bolt



30. REMOVE ENGINE WATER PUMP ASSEMBLY


    A348245
  1. Remove the 7 bolts, engine water pump assembly and water pump gasket.



31. REMOVE WATER INLET


    A348247
  1. Remove the 2 nuts and water inlet.



32. REMOVE THERMOSTAT
  1. Remove the thermostat from the water inlet housing.

  1. Remove the gasket from the thermostat.



33. REMOVE OIL COOLER ASSEMBLY


    A207599E07
  1. Remove the oil cooler union bolt and seal washer.
    Text in Illustration 
    *1
    Oil Cooler Union Bolt
    *2
    Seal Washer

  1. Remove the nut and oil cooler assembly from the water inlet housing.

  1. Remove the 3 gaskets from the oil cooler assembly.



34. REMOVE ENGINE OIL TEMPERATURE SENSOR


    A338023
  1. Disconnect the engine oil temperature sensor connector.



    A338024E01
  1. Using SST, remove the engine oil temperature sensor from the water inlet housing sub-assembly.
    Text in Illustration 
    *1
    Engine Oil Temperature Sensor
    *2
    Gasket

    SST
    09817-33191  

    NOTICE:
    If the engine oil temperature sensor has been struck or dropped, replace it.

  1. Remove the gasket from the engine oil temperature sensor.



35. REMOVE WATER INLET HOUSING


    A337917
  1. Remove the 4 bolts, nut, water inlet housing and gasket.
    V100135
    Bolt
    V100136
    Nut

    NOTICE:
    If a stud bolt is deformed or its threads are damaged, replace it.



36. REMOVE IGNITION COIL ASSEMBLY


    A338015
  1. Disconnect the 4 ignition coil assembly connectors.

  1. Remove the 4 bolts and 4 ignition coil assemblies from the cylinder head cover sub-assembly.

    NOTICE:
    If an ignition coil assembly has been struck or dropped, replace it.

    HINT:
    Arrange the removed parts in the correct order.



37. REMOVE BRACKET


    A339021
  1. Remove the bolt and bracket from the cylinder head cover sub-assembly.