ENGINE UNIT > DISASSEMBLY |
| 1. REMOVE VACUUM PUMP ASSEMBLY |
![]() |
Remove the 4 bolts and vacuum pump assembly.
![]() |
Remove the No. 2 O-ring and No. 3 O-ring from the vacuum pump assembly.
| *1 | No. 2 O-ring |
| *2 | No. 3 O-ring |
| 2. REMOVE KNOCK CONTROL SENSOR |
![]() |
Disconnect the knock control sensor connector.
Remove the bolt and knock control sensor from the cylinder block sub-assembly.
| 3. REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY |
Disconnect the oil pressure sender gauge assembly connector.
![]() |
Using a 27 mm deep socket wrench, remove the oil pressure sender gauge assembly.
| 4. REMOVE ENGINE COOLANT TEMPERATURE SENSOR |
![]() |
Disconnect the engine coolant temperature sensor connector.
![]() |
Using SST, remove the engine coolant temperature sensor from the cylinder head sub-assembly.
| *1 | Engine Coolant Temperature Sensor |
| *2 | Gasket |
Remove the gasket from the engine coolant temperature sensor.
| 5. REMOVE ENGINE COVER JOINT |
![]() |
Remove the 2 engine cover joints.
| 6. REMOVE SPARK PLUG |
![]() |
Remove the 4 spark plugs from the cylinder head sub-assembly.
| 7. REMOVE OIL FILLER CAP SUB-ASSEMBLY |
Remove the oil filler cap sub-assembly from the cylinder head cover sub-assembly.
Remove the gasket from the oil filler cap sub-assembly.
| 8. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
![]() |
Disconnect the camshaft timing oil control valve assembly connector.
Remove the bolt and camshaft timing oil control valve assembly from the cylinder head cover sub-assembly.
![]() |
Remove the O-ring from the camshaft timing oil control valve assembly.
| *1 | O-ring |
| 9. REMOVE CAMSHAFT POSITION SENSOR (for Intake Side) |
![]() |
Disconnect the camshaft position sensor connector.
Remove the bolt and camshaft position sensor from the cylinder head cover sub-assembly.
| 10. REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side) |
![]() |
Disconnect the camshaft position sensor connector.
Remove the bolt and camshaft position sensor from the cylinder head cover sub-assembly.
| 11. REMOVE PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY) |
![]() |
Using a 19 mm deep socket wrench, remove the PCV valve (ventilation valve sub-assembly) from the cylinder head cover sub-assembly.
| 12. REMOVE NO. 1 VENTILATION CASE |
![]() |
Remove the 8 bolts and 2 nuts.
![]() | Bolt |
![]() | Nut |
![]() |
Remove the No. 1 ventilation case by prying between the No. 1 ventilation case and cylinder block sub-assembly with a screwdriver.
| 13. REMOVE CRANKSHAFT POSITION SENSOR |
![]() |
Disconnect the crankshaft position sensor connector.
Remove the bolt and crankshaft position sensor from the timing chain cover sub-assembly.
| 14. REMOVE CRANKSHAFT PULLEY |
![]() |
Using SST, hold the crankshaft pulley and loosen the crankshaft pulley set bolt. Further loosen the crankshaft pulley set bolt until 2 or 3 threads are screwed into the crankshaft.
| *a | Hold |
| *b | Turn |
![]() |
Using SST and the crankshaft pulley set bolt, remove the crankshaft pulley and crankshaft pulley set bolt.
| *1 | Crankshaft Pulley Set Bolt |
| *a | Hold |
| *b | Turn |
| 15. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Remove the 17 bolts, 3 seal washers, cylinder head cover sub-assembly and cylinder head cover gasket.
![]() | Bolt |
![]() | Bolt with Seal Washer |
![]() |
Remove the camshaft bearing cap oil hole gasket from the No. 1 camshaft bearing cap.
| *1 | Camshaft Bearing Cap Oil Hole Gasket |
| *a | Gasket |
Remove the gasket from the No. 2 camshaft bearing cap.
| 16. REMOVE CASE SEPARATOR |
![]() |
Remove the 2 bolts and case separator from the cylinder head cover case sub-assembly.
![]() |
Remove the oil separator gasket from the case separator.
![]() |
Remove the O-ring from the case separator.
| *a | O-ring |
| 17. REMOVE SPARK PLUG TUBE GASKET |
![]() |
Using a screwdriver, pry out the 4 spark plug tube gaskets from the cylinder head cover sub-assembly.
| *a | Protective Tape |
| 18. REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY |
![]() |
Disconnect the camshaft timing oil control solenoid assembly connector.
Remove the 2 bolts and camshaft timing oil control solenoid assembly from the timing chain cover sub-assembly.
![]() |
Remove the O-ring from the camshaft timing oil control solenoid assembly.
| 19. REMOVE TIMING CHAIN COVER PLATE |
![]() |
Remove the 4 bolts, timing chain cover plate and gasket.
| 20. REMOVE ENGINE MOUNTING BRACKET RH |
![]() |
Remove the 5 bolts and engine mounting bracket RH.
| 21. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY |
![]() |
Remove the 17 bolts and 2 nuts.
![]() | Bolt |
![]() | Nut |
Remove the timing chain cover sub-assembly by prying between the timing chain cover sub-assembly and cylinder head sub-assembly, camshaft housing sub-assembly, cylinder block and stiffening crankcase assembly with a screwdriver as shown in the illustration.

| *a | Protective Tape | - | - |
![]() |
Remove the 2 oil pump gaskets and oil hole cover gasket from the stiffening crankcase assembly.
| *1 | Oil Pump Gasket |
| *2 | Oil Hole Cover Gasket |
| 22. REMOVE TIMING CHAIN COVER OIL SEAL |
![]() |
Using a screwdriver and wooden block, pry out the timing chain cover oil seal.
| *a | Protective Tape |
| *b | Wooden Block |
| 23. SET NO. 1 CYLINDER TO TDC/COMPRESSION |
Temporarily install the crankshaft pulley set bolt.

| *1 | Crankshaft Pulley Key | - | - |
| *a | Approximately 7° | *b | Approximately 32° |
| *c | Timing Mark | - | - |
Rotate the crankshaft clockwise and align the crankshaft pulley key as shown in the illustration.
Check that the timing marks on the camshaft timing exhaust gear assembly and camshaft timing gear assembly are as shown in the illustration.
Remove the crankshaft pulley set bolt.
| 24. REMOVE TIMING CHAIN GUIDE |
![]() |
Remove the bolt and timing chain guide.
| 25. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY |
![]() |
Allow the plunger to extend slightly, and then turn the stopper plate counterclockwise to release the lock. Once the lock is released, push the plunger into the No. 1 chain tensioner assembly.
| *a | Stopper Plate |
| *b | Plunger |
![]() |
Turn the stopper plate clockwise to set the lock, and insert a pin into the stopper plate hole.
| *a | Pin |
![]() |
Remove the 2 bolts, No. 1 chain tensioner assembly and gasket.
| 26. REMOVE CHAIN TENSIONER SLIPPER |
![]() |
Remove the bolt and chain tensioner slipper.
| 27. REMOVE CHAIN SUB-ASSEMBLY |
Remove the chain sub-assembly.
| 28. REMOVE NO. 1 CHAIN VIBRATION DAMPER |
![]() |
Remove the 2 bolts and No. 1 chain vibration damper.
| 29. REMOVE CRANKSHAFT TIMING SPROCKET |
![]() |
Remove the crankshaft timing sprocket from the crankshaft.
| 30. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY |
![]() |
Using a wrench to hold the hexagonal portion of the camshaft, remove the camshaft timing gear bolt and camshaft timing gear assembly.
| *a | Hold |
![]() | Turn |
| 31. REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY |
![]() |
Using a wrench to hold the hexagonal portion of the No. 2 camshaft, remove the bolt and camshaft timing exhaust gear assembly.
| *a | Hold |
![]() | Turn |
| 32. REMOVE OIL PIPE SUB-ASSEMBLY |
![]() |
Remove the bolt and oil pipe sub-assembly from the No. 4 camshaft bearing cap.
| 33. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY |
![]() |
Uniformly loosen and remove the 20 bolts in the order shown in the illustration.
![]() |
Remove the camshaft housing sub-assembly by prying between the cylinder head sub-assembly and camshaft housing sub-assembly with a screwdriver.
| 34. REMOVE CAMSHAFT BEARING CAP |
![]() |
Remove the 11 bolts in the order shown in the illustration.
Remove the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, No. 3 camshaft bearing cap and No. 4 camshaft bearing cap.
| 35. REMOVE CAMSHAFT |
Remove the camshaft from the camshaft housing sub-assembly.
| 36. REMOVE NO. 2 CAMSHAFT |
Remove the No. 2 camshaft from the camshaft housing sub-assembly.
| 37. REMOVE OIL CONTROL VALVE FILTER |
![]() |
Remove the oil control valve filter from the No. 1 camshaft bearing cap.
| 38. REMOVE NO. 1 CAMSHAFT BEARING |
![]() |
Remove the No. 1 camshaft bearing from the No. 1 camshaft bearing cap.
| 39. REMOVE NO. 2 CAMSHAFT BEARING |
![]() |
Remove the No. 2 camshaft bearing from the camshaft housing sub-assembly.
| 40. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
Remove the 16 No. 1 valve rocker arm sub-assemblies.
| 41. REMOVE VALVE LASH ADJUSTER ASSEMBLY |
Remove the 16 valve lash adjuster assemblies from the cylinder head sub-assembly.
| 42. REMOVE VALVE STEM CAP |
Remove the 16 valve stem caps from the cylinder head sub-assembly.
| 43. REMOVE CAMSHAFT HOUSING STUD BOLT |
| 44. REMOVE CAMSHAFT BEARING CAP SETTING RING PIN |
| 45. REMOVE CAMSHAFT HOUSING STRAIGHT PIN |
| 46. REMOVE CYLINDER HEAD SUB-ASSEMBLY |
![]() |
Using a 10 mm bi-hexagon wrench, uniformly loosen the 10 cylinder head set bolts in the order shown in the illustration. Remove the 10 cylinder head set bolts and 10 plate washers.
Remove the cylinder head sub-assembly.
| 47. REMOVE CYLINDER HEAD GASKET |
Remove the cylinder head gasket from the cylinder block sub-assembly.
| 48. REMOVE CYLINDER BLOCK WATER JACKET SPACER |
![]() |
Remove the cylinder block water jacket spacer from the cylinder block sub-assembly.
| 49. REMOVE OIL FILTER CAP ASSEMBLY |
![]() |
Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
| *a | Pipe |
| *b | Hose |
![]() |
Remove the oil filter drain plug from the oil filter cap assembly.
![]() |
Insert the pipe with hose into the oil filter cap assembly.
| *1 | Oil Filter Cap Assembly |
| *2 | O-ring |
| *a | Valve |
| *b | Hose |
![]() |
Make sure that the engine oil is completely drained, and remove the pipe with hose and O-ring.
![]() |
Using SST, remove the oil filter cap assembly.
| *1 | Oil Filter Bracket Clip |
![]() |
Remove the oil filter element and O-ring from the oil filter cap assembly.
| *1 | Oil Filter Element |
| *2 | Oil Filter Cap Assembly |
| *3 | O-ring |
| 50. REMOVE OIL PAN DRAIN PLUG |
Remove the oil pan drain plug and gasket from the oil pan sub-assembly.
| 51. REMOVE OIL PAN SUB-ASSEMBLY |
![]() |
Remove the 11 bolts and 2 nuts.
| *A | Type A |
| *B | Type B |
![]() | Bolt |
![]() | Nut |
![]() |
Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and stiffening crankcase assembly, cut through the applied sealer and remove the oil pan sub-assembly.
| 52. REMOVE OIL STRAINER SUB-ASSEMBLY |
![]() |
Remove the 3 bolts, oil strainer sub-assembly and gasket.
| 53. REMOVE ENGINE OIL LEVEL SENSOR |
Disconnect the engine oil level sensor connector.
![]() |
Remove the clip from the engine oil level sensor.
![]() |
Remove the 2 bolts.
Disengage the clamp to remove the engine oil level sensor.
| 54. REMOVE OIL LEVEL SENSOR BRACKET |
![]() |
Remove the 2 bolts and oil level sensor bracket from the stiffening crankcase assembly.
| 55. REMOVE NO. 1 OIL PAN BAFFLE PLATE |
![]() |
Remove the clamp from the No. 1 oil pan baffle plate.
Remove the 4 bolts and No. 1 oil pan baffle plate.
| 56. INSPECT CRANKSHAFT BACKLASH |
![]() |
Using a dial indicator, measure the backlash of the crankshaft and balance shaft as shown in the illustration.
| 57. REMOVE ENGINE BALANCER ASSEMBLY |
![]() |
Remove the 7 bolts and engine balancer assembly from the stiffening crankcase assembly.
| 58. INSPECT NO. 1 BALANCE SHAFT THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance while moving the No. 1 balance shaft back and forth.
| 59. INSPECT NO. 2 BALANCE SHAFT THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance while moving the No. 2 balance shaft back and forth.
| 60. REMOVE STIFFENING CRANKCASE ASSEMBLY |
![]() |
Remove the 7 bolts.
![]() |
Using a screwdriver, remove the stiffening crankcase assembly by prying between the stiffening crankcase assembly and cylinder block sub-assembly at the places shown in the illustration.
| *a | LH Side |
| *b | RH Side |
| 61. REMOVE OIL FILTER BRACKET CLIP |
![]() |
Remove the oil filter bracket clip from the stiffening crankcase assembly.
| 62. REMOVE STIFFENING CRANKCASE STUD BOLT |
| 63. REMOVE STIFFENING CRANKCASE RING PIN |
| 64. REMOVE REAR ENGINE OIL SEAL |
Remove the rear engine oil seal from the cylinder block sub-assembly.