Home › Engine / Hybrid System ยท 6AR-FSE › ENGINE MECHANICAL › CYLINDER HEAD

CYLINDER HEAD > REPLACEMENT

for Preparation Click here



1. REPLACE INTAKE VALVE GUIDE BUSH
  1. Heat the cylinder head sub-assembly to approximately 80 to 100°C (176 to 212°F).

  1. Place the cylinder head sub-assembly on wooden blocks.



    A194970E04
  1. Using SST and a hammer, tap out the intake valve guide bush.

    SST
    09201-01055  
    09950-70010   (09951-07100)



    A194985
  1. Using a caliper gauge, measure the intake valve guide bush bore diameter of the cylinder head sub-assembly.

    Standard Intake Valve Guide Bush Bore Diameter:
    10.285 to 10.306 mm (0.405 to 0.406 in.)

    Select a new intake valve guide bush (STD or O/S 0.05):
    Bush Size
    Bush Bore Diameter
    STD
    10.333 to 10.344 mm
    (0.40681 to 0.40724 in.)
    O/S 0.05
    10.383 to 10.394 mm
    (0.40878 to 0.40921 in.)

    Standard Bush Length:
    41.3 to 41.7 mm (1.63 to 1.64 in.)

    If the intake valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.306 mm (0.406 in.), machine the intake valve guide bush bore of the cylinder head sub-assembly to a dimension of 10.335 to 10.356 mm (0.407 to 0.408 in.) to install an O/S 0.05 intake valve guide bush.
    If the intake valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.356 mm (0.408 in.), replace the cylinder head sub-assembly.

  1. Heat the cylinder head sub-assembly to approximately 80 to 100°C (176 to 212°F).



    A337941E01
  1. Using SST and a hammer, tap in the selected intake valve guide bush.
    Text in Illustration 
    *a
    Protrusion Height

    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

    Standard Protrusion Height:
    14.85 to 15.1 mm (0.585 to 0.594 in.)



    A337942
  1. Using a sharp 5.5 mm reamer, ream the intake valve guide bush to obtain the standard oil clearance.

    Standard Oil Clearance:
    0.025 to 0.060 mm (0.000984 to 0.00236 in.)



2. REPLACE EXHAUST VALVE GUIDE BUSH
  1. Heat the cylinder head sub-assembly to approximately 80 to 100°C (176 to 212°F).

  1. Place the cylinder head sub-assembly on wooden blocks.



    A337943E01
  1. Using SST and a hammer, tap out the exhaust valve guide bush.

    SST
    09201-01055  
    09950-70010   (09951-07100)

  1. Using a caliper gauge, measure the exhaust valve guide bush bore diameter of the cylinder head sub-assembly.

    Standard Exhaust Valve Guide Bush Bore Diameter:
    10.285 to 10.306 mm (0.405 to 0.406 in.)

    Select a new exhaust valve guide bush (STD or O/S 0.05):
    Bush Size
    Bush Bore Diameter
    STD
    10.333 to 10.344 mm
    (0.40681 to 0.40724 in.)
    O/S 0.05
    10.383 to 10.394 mm
    (0.40878 to 0.40921 in.)

    Standard Bush Length:
    46.8 to 47.2 mm (1.84 to 1.86 in.)

    If the exhaust valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.306 mm (0.406 in.), machine the exhaust valve guide bush bore of the cylinder head sub-assembly to a dimension of 10.335 to 10.356 mm (0.407 to 0.408 in.) to install an O/S 0.05 exhaust valve guide bush.
    If the exhaust valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.356 mm (0.408 in.), replace the cylinder head sub-assembly.

  1. Heat the cylinder head sub-assembly to approximately 80 to 100°C (176 to 212°F).



    A337944E01
  1. Using SST and a hammer, tap in the selected exhaust valve guide bush.
    Text in Illustration 
    *a
    Protrusion Height

    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

    Standard Protrusion Height:
    14.25 to 14.5 mm (0.561 to 0.571 in.)



    A337945
  1. Using a sharp 5.5 mm reamer, ream the exhaust valve guide bush to obtain the standard oil clearance.

    Standard Oil Clearance:
    0.030 to 0.065 mm (0.00118 to 0.00256 in.)



3. REPLACE RING PIN

NOTICE:
It is not necessary to remove the ring pins unless they are being replaced.

  1. Remove the 2 ring pins.



    A336671E01
  1. Using a plastic hammer, tap in 2 new ring pins to the cylinder head sub-assembly.
    Text in Illustration 
    *a
    Protrusion Height

    Standard Protrusion Height:
    6.5 to 7.5 mm (0.256 to 0.295 in.)