CYLINDER HEAD > INSPECTION |
| 1. INSPECT CYLINDER HEAD SUB-ASSEMBLY |
Using a precision straightedge and feeler gauge, measure the warpage of the contact surfaces where the cylinder head sub-assembly contacts the cylinder block sub-assembly, intake manifold and exhaust manifold converter sub-assembly (TWC: Front Catalyst).

| *a | Cylinder Block Sub-assembly Side | *b | Intake Manifold Side |
| *c | Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst) Side | - | - |
| Item | Specified Condition |
| Cylinder block sub-assembly side | 0.05 mm (0.00197 in.) |
| Intake manifold side | 0.10 mm (0.00394 in.) |
| Exhaust manifold converter sub-assembly (TWC: Front Catalyst) side | 0.10 mm (0.00394 in.) |
![]() |
Using a dye penetrant, check the intake ports, exhaust ports and cylinder head sub-assembly surface for cracks.
If cracks are found, replace the cylinder head sub-assembly.
| 2. INSPECT COMPRESSION SPRING |
![]() |
Using a vernier caliper, measure the free length of the compression spring.
![]() |
Using a steel square, measure the deviation of the compression spring.
| *a | Deviation |
| *b | 36.7 mm (1.44 in.) |
| 3. INSPECT INTAKE VALVE |
![]() |
Using a micrometer, measure the diameter of the valve stem.
![]() |
Using a vernier caliper, measure the valve head margin thickness.
| *a | Margin Thickness |
![]() |
Using a vernier caliper, measure the overall length of the intake valve.
| *a | Overall Length |
| 4. INSPECT EXHAUST VALVE |
![]() |
Using a micrometer, measure the diameter of the valve stem.
![]() |
Using a vernier caliper, measure the valve head margin thickness.
| *a | Margin Thickness |
![]() |
Using a vernier caliper, measure the overall length of the exhaust valve.
| *a | Overall Length |
| 5. INSPECT VALVE GUIDE BUSH OIL CLEARANCE |
![]() |
Using a caliper gauge, measure the inside diameter of the valve guide bush.
Subtract the valve stem diameter measurement from the valve guide bush inside diameter measurement.
| Item | Specified Condition |
| Intake | 0.025 to 0.060 mm (0.000984 to 0.00236 in.) |
| Exhaust | 0.030 to 0.065 mm (0.00118 to 0.00256 in.) |
| Item | Specified Condition |
| Intake | 0.08 mm (0.00315 in.) |
| Exhaust | 0.10 mm (0.00394 in.) |
| 6. INSPECT INTAKE VALVE SEAT |
Apply a light coat of Prussian blue to the valve face.
![]() |
Lightly press the valve face against the intake valve seat.
| *a | Width |
Check the valve face and intake valve seat by using the following procedure:
If Prussian blue appears 360° around the entire intake valve face, the valve face is concentric. If not, replace the intake valve.
If Prussian blue appears 360° around the entire intake valve seat, the intake valve seat and valve face are concentric. If not, resurface the intake valve seat.
Check that the intake valve seat contacts the middle of the valve face with the width between 1.0 to 1.4 mm (0.0394 to 0.0551 in.).
| 7. INSPECT EXHAUST VALVE SEAT |
Apply a light coat of Prussian blue to the valve face.
![]() |
Lightly press the valve face against the exhaust valve seat.
| *a | Width |
Check the valve face and exhaust valve seat by using the following procedure:
If Prussian blue appears 360° around the entire exhaust valve face, the valve face is concentric. If not, replace the exhaust valve.
If Prussian blue appears 360° around the entire exhaust valve seat, the exhaust valve seat and valve face are concentric. If not, resurface the exhaust valve seat.
Check that the exhaust valve seat contacts the middle of the valve face with the width between 1.2 to 1.6 mm (0.0472 to 0.0630 in.).