CYLINDER BLOCK > INSPECTION |
| 1. INSPECT CYLINDER BLOCK FOR WARPAGE |
![]() |
Using a precision straightedge and feeler gauge, measure the warpage of the surface which contacts the cylinder head gasket.
| 2. INSPECT CYLINDER BORE |
![]() |
Using a cylinder gauge, measure the cylinder bore diameter at positions (A) and (B) in the thrust and axial directions.
| *a | Axial Direction |
| *b | Thrust Direction |
| *c | 10 mm (0.394 in.) |
| *d | Center |
![]() | Front |
| 3. INSPECT PISTON |
![]() |
Using a gasket scraper, remove any carbon from the piston top.
![]() |
Using a groove cleaning tool or a broken ring, clean the piston ring grooves.
![]() |
Using a brush and solvent, thoroughly clean the piston.
![]() |
Using a micrometer, measure the piston diameter at a right angle to the piston center line where the distance from the bottom of the piston is as specified.
| *a | Distance |
| 4. INSPECT PISTON OIL CLEARANCE |
Measure the cylinder bore diameter in the thrust direction.
Subtract the piston diameter measurement from the cylinder bore diameter measurement.
| 5. INSPECT RING GROOVE CLEARANCE |
![]() |
Using a feeler gauge, measure the clearance between a new piston ring set and the wall of the ring groove.
| Item | Specified Condition |
| No. 1 compression ring | 0.020 to 0.070 mm (0.000787 to 0.00276 in.) |
| No. 2 compression ring | 0.020 to 0.060 mm (0.000787 to 0.00236 in.) |
| Oil ring | 0.070 to 0.150 mm (0.00276 to 0.00591 in.) |
| 6. INSPECT PISTON RING END GAP |
![]() |
Insert the piston ring into the cylinder bore.
| *a | Piston Ring |
| *b | 120 mm (4.72 in.) |
Using a piston, push in the piston ring a little beyond the bottom of the ring travel, 120 mm (4.72 in.) from the top of the cylinder block sub-assembly.
![]() |
Using a feeler gauge, measure the end gap.
| Item | Specified Condition |
| No. 1 compression ring | 0.20 to 0.25 mm (0.00787 to 0.00984 in.) |
| No. 2 compression ring | 0.32 to 0.37 mm (0.0126 to 0.0146 in.) |
| Oil ring | 0.10 to 0.35 mm (0.00394 to 0.0138 in.) |
| Item | Specified Condition |
| No. 1 compression ring | 0.81 mm (0.0319 in.) |
| No. 2 compression ring | 0.90 mm (0.0354 in.) |
| Oil ring | 1.40 mm (0.0551 in.) |
| 7. INSPECT PISTON PIN OIL CLEARANCE |
Check each mark on the piston, piston pin and connecting rod sub-assembly.

| *a | Front Mark | *b | Piston Pin Hole Inside Diameter Mark |
| *c | Connecting Rod Small End Bush Inside Diameter Mark | - | - |
![]() |
Using a caliper gauge, measure the inside diameter of the piston pin hole.
| Mark | Specified Condition |
| A | 22.001 to 22.004 mm (0.86618 to 0.86630 in.) |
| B | 22.005 to 22.007 mm (0.86634 to 0.86642 in.) |
| C | 22.008 to 22.010 mm (0.86645 to 0.86653 in.) |
![]() |
Using a micrometer, measure the piston pin diameter.
| *a | 5.0 mm (0.197 in.) |
| *b | 28 mm (1.10 in.) |
| Mark | Specified Condition |
| A | 21.997 to 22.000 mm (0.86602 to 0.86614 in.) |
| B | 22.001 to 22.003 mm (0.86618 to 0.86626 in.) |
| C | 22.004 to 22.006 mm (0.86630 to 0.86638 in.) |
![]() |
Using a caliper gauge, measure the inside diameter of the connecting rod small end bush.
| Mark | Specified Condition |
| A | 22.005 to 22.008 mm (0.86634 to 0.86645 in.) |
| B | 22.009 to 22.011 mm (0.86649 to 0.86657 in.) |
| C | 22.012 to 22.014 mm (0.86661 to 0.86669 in.) |
Subtract the piston pin diameter measurement from the piston pin hole inside diameter measurement.
Subtract the piston pin diameter measurement from the connecting rod small end bush inside diameter measurement.
| 8. INSPECT CONNECTING ROD SUB-ASSEMBLY |
![]() |
Using a connecting rod aligner and feeler gauge, check the connecting rod sub-assembly alignment.
Check for misalignment.
![]() |
Check for twist.
| 9. INSPECT CRANKSHAFT |
Inspect for runout.
Clean the crank journal.
Place the crankshaft on V-blocks.
![]() |
Using a dial indicator and V-blocks, measure the runout as shown in the illustration.
![]() |
Inspect the main journals.
Using a micrometer, measure the diameter of each main journal.
Check each main journal for taper and out-of-round as shown in the illustration.
![]() |
Inspect the crank pin.
Using a micrometer, measure the diameter of each crank pin.
Inspect each crank pin for taper and out-of-round as shown in the illustration.
| 10. INSPECT CRANKSHAFT OIL CLEARANCE |
Install the crankshaft bearings .
Install the crankshaft thrust washers .
Clean each main journal and crankshaft bearing.
![]() |
Place the crankshaft on the cylinder block sub-assembly.
| *a | Plastigage |
Lay a strip of Plastigage across each journal.
Install the crankshaft bearing caps .
Remove the crankshaft bearing caps .
![]() ![]() |
Measure the Plastigage at its widest point.
| *a | Plastigage |
| *a | Cylinder Block Number Mark (A) | *b | Crankshaft Number Mark (B) |
| *c | Diameter Mark | - | - |
| (A) + (B) | Use Crankshaft Bearing |
| 0 to 2 | 1 |
| 3 to 5 | 2 |
| 6 to 8 | 3 |
| 9 to 11 | 4 |
| Mark | Specified Condition |
| 0 | 59.000 to 59.002 mm (2.32283 to 2.32291 in.) |
| 1 | 59.003 to 59.004 mm (2.32295 to 2.32299 in.) |
| 2 | 59.005 to 59.006 mm (2.32303 to 2.32307 in.) |
| 3 | 59.007 to 59.009 mm (2.32311 to 2.32318 in.) |
| 4 | 59.010 to 59.011 mm (2.32322 to 2.32326 in.) |
| 5 | 59.012 to 59.013 mm (2.32330 to 2.32334 in.) |
| 6 | 59.014 to 59.016 mm (2.32338 to 2.32346 in.) |
| Mark | Specified Condition |
| 0 | 54.999 to 55.000 mm (2.16531 to 2.16535 in.) |
| 1 | 54.997 to 54.998 mm (2.16523 to 2.16527 in.) |
| 2 | 54.995 to 54.996 mm (2.16515 to 2.16519 in.) |
| 3 | 54.993 to 54.994 mm (2.16507 to 2.16511 in.) |
| 4 | 54.991 to 54.992 mm (2.16500 to 2.16504 in.) |
| 5 | 54.988 to 54.990 mm (2.16488 to 2.16496 in.) |
| Mark | Specified Condition |
| 1 | 1.992 to 1.995 mm (0.07843 to 0.07854 in.) |
| 2 | 1.996 to 1.998 mm (0.07858 to 0.07866 in.) |
| 3 | 1.999 to 2.001 mm (0.07870 to 0.07878 in.) |
| 4 | 2.002 to 2.004 mm (0.07882 to 0.07890 in.) |
Perform the inspection for each journal.
| 11. INSPECT CRANKSHAFT BEARING CAP BOLT |
![]() |
Using a vernier caliper, measure the diameter of the threads at the measurement point.
| *a | Measurement Point |
| 12. INSPECT CONNECTING ROD BOLT |
![]() |
Using a vernier caliper, measure the diameter of the connecting rod bolt at several points within the area shown in the illustration.
| *a | Measurement Area |
| 13. INSPECT NO. 1 OIL NOZZLE SUB-ASSEMBLY |
![]() |
Push the check valve with a pin to check if it is stuck.
| *a | Pin |
Push the check valve with a pin to check if it moves smoothly.
If the check valve does not move smoothly, clean or replace the No. 1 oil nozzle sub-assembly.
![]() |
Apply air to (A). Check that air does not leak through (B).
If air leaks, clean or replace the No. 1 oil nozzle sub-assembly.
![]() |
Push the check valve with a pin while applying air to (A). Check that air passes through (B).
| *a | Pin |