CYLINDER BLOCK > DISASSEMBLY |
| 1. INSPECT CONNECTING ROD THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance while moving the connecting rod sub-assembly back and forth.
| 2. INSPECT CONNECTING ROD OIL CLEARANCE |
![]() |
Check the alignment marks on the connecting rod and connecting rod cap to ensure correct reassembly.
| *a | Alignment Mark |
![]() |
Remove the 2 connecting rod bolts and connecting rod cap.
Clean the crank pin and connecting rod bearing.
Check the crank pin and connecting rod bearing for pitting and scratches.
If the crank pin or connecting rod bearing is damaged, replace the connecting rod bearings. If necessary, replace the crankshaft.
![]() |
Lay a strip of Plastigage on the crank pin.
| *a | Plastigage |
![]() |
Check that the front mark of the connecting rod cap is facing in the correct direction, and install the connecting rod cap.
| *a | Front Mark |
![]() |
Apply a light coat of engine oil to the threads and under the heads of the 2 connecting rod bolts.
Install and alternately tighten the 2 connecting rod bolts in several steps.
![]() |
Mark the front of each connecting rod bolt with paint.
| *a | Paint Mark |
![]() | Engine Front |
Tighten the connecting rod bolts by 90° as shown in the illustration.
Remove the 2 connecting rod bolts and connecting rod cap.
![]() |
Measure the Plastigage at its widest point.
| *a | Plastigage |
| *b | Number Mark |
| Mark | Specified Condition |
| 1 | 54.500 to 54.508 mm (2.14567 to 2.14598 in.) |
| 2 | 54.509 to 54.516 mm (2.14602 to 2.14629 in.) |
| 3 | 54.517 to 54.524 mm (2.14633 to 2.14661 in.) |
| Mark | Specified Condition |
| 1 | 1.486 to 1.490 mm (0.0585 to 0.0587 in.) |
| 2 | 1.491 to 1.494 mm (0.0587 to 0.0588 in.) |
| 3 | 1.495 to 1.498 mm (0.0589 to 0.0590 in.) |
Perform the inspection for each cylinder.
| 3. REMOVE PISTON WITH CONNECTING ROD |
![]() |
Using a ridge reamer, remove all the carbon from the top of the cylinder.
| *a | Ridge Reamer |
Remove the 8 connecting rod bolts and 4 connecting rod caps.
Push the piston with connecting rod and connecting rod bearing through the top of the cylinder block sub-assembly.
| 4. REMOVE CONNECTING ROD BEARING |
Remove the connecting rod bearings from the connecting rods and connecting rod caps.
| 5. INSPECT CRANKSHAFT THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.
| 6. REMOVE CRANKSHAFT |
![]() |
Uniformly loosen and remove the 10 crankshaft bearing cap bolts in several steps in the order shown in the illustration.
Remove the 5 crankshaft bearing caps from the cylinder block sub-assembly.
Remove the crankshaft from the cylinder block sub-assembly.
Check each crankshaft journal and crankshaft bearing for pitting and scratches.
If the journal or crankshaft bearing is damaged, replace the crankshaft bearings. If necessary, replace the crankshaft.
| 7. REMOVE CRANKSHAFT THRUST WASHER |
![]() |
Remove the 2 crankshaft thrust washers from the cylinder block sub-assembly.
| 8. REMOVE CRANKSHAFT BEARING |
Remove the crankshaft bearings and No. 2 crankshaft bearings from the cylinder block sub-assembly and crankshaft bearing caps.
| 9. REMOVE CRANKSHAFT PULLEY KEY |
Using a screwdriver, remove the 2 crankshaft pulley keys from the crankshaft.
| 10. REMOVE PISTON RING SET |
![]() |
Using a piston ring expander, remove the No. 1 compression ring and No. 2 compression ring.
| *a | Piston Ring Expander |
Remove the oil ring expander, upper side rail and lower side rail by hand.
| 11. REMOVE PISTON PIN HOLE SNAP RING |
![]() |
Using a screwdriver, pry out the piston pin hole snap ring (front side).
| *a | Protective Tape |
| *b | Cutout |
| 12. REMOVE PISTON |
![]() |
Gradually heat each piston to 80 to 90°C (176 to 194°F).
![]() |
Using a hammer and brass bar, lightly tap out the piston pin. Then remove the connecting rod sub-assembly.
| 13. REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY |
![]() |
Using a 5 mm hexagon wrench, remove the 4 bolts and 4 No. 1 oil nozzle sub-assemblies.
| 14. REMOVE STUD BOLT |