Home › General › SPECIFICATIONS › 6AR-FSE ENGINE CONTROL

6AR-FSE ENGINE CONTROL > SERVICE DATA



SPARK PLUG 
Standard Insulation Resistance
Spark plug (terminal part) - Body ground
10 MΩ or higher
Spark Plug Type
DENSO made
FK16HBR-J8
Maximum Electrode Gap
for Used Spark Plug
1.1 mm (0.0433 in.)
Standard Electrode Gap
for New Spark Plug
0.7 to 0.8 mm (0.0276 to 0.0315 in.)

CAMSHAFT TIMING GEAR BOLT 
Standard stroke
Plunger
4.5 mm (0.177 in.) or more

CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY 
Standard Resistance
20°C (68°F)
6.9 to 7.9 Ω

CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY 
Plunger extends outwards
Apply battery voltage between the terminals
5.9 mm (0.232 in.) or higher

THROTTLE BODY WITH MOTOR ASSEMBLY 
Standard Throttle Valve Opening Percentage
Shift lever in N
60% or higher
Standard Resistance
20°C (68°F)
0.3 to 100 Ω

ACCELERATOR PEDAL SENSOR ASSEMBLY 
Standard Voltage (Accelerator Position Sensor No. 1 Voltage)
Accelerator pedal fully released
0.5 to 1.1 V
Accelerator pedal fully depressed
2.6 to 4.5 V
Standard Voltage (Accelerator Position Sensor No. 2 Voltage)
Accelerator pedal fully released
1.2 to 2.0 V
Accelerator pedal fully depressed
3.4 to 4.75 V

MASS AIR FLOW METER SUB-ASSEMBLY 
Mass Air Flow Sensor
Idling (After the engine warms up)
1.0 to 4.0 gm/sec
2000 rpm (After the engine warms up)
4.1 to 8.1 gm/sec
3000 rpm (After the engine warms up)
6.2 to 11.2 gm/sec
Standard Resistance
4 (THA) - 2 (E2G)
-20°C (-4°F)
13.6 to 18.4 kΩ
20°C (68°F)
2.21 to 2.69 kΩ
60°C (140°F)
0.49 to 0.67 kΩ

ENGINE COOLANT TEMPERATURE SENSOR 
Standard Resistance
20°C (68°F)
2.32 to 2.59 kΩ
80°C (176°F)
0.310 to 0.326 kΩ

ENGINE OIL TEMPERATURE SENSOR 
Standard Resistance
30°C (86°F)
2.465 to 3.213 kΩ

KNOCK CONTROL SENSOR 
Standard Resistance
25°C (77°F)
120 to 280 kΩ

AIR FUEL RATIO SENSOR 
Standard Resistance
1 (HA1A) - 2 (+B)
20°C (68°F)
1.6 to 3.2 Ω
1 (HA1A) - 4 (A1A-)
Always
10 kΩ or higher

HEATED OXYGEN SENSOR 
Standard Resistance
1 (HT1B) - 2 (+B)
20°C (68°F)
9 to 14 Ω
1 (HT1B) - 4 (E2)
Always
10 kΩ or higher

EFI MAIN RELAY (NO. 1 INTEGRATION RELAY) 
Standard Resistance
1A-8 - 1B-1
Battery voltage not applied between terminals 1C-7 and 1E-2
10 kΩ or higher
1A-8 - 1B-1
Battery voltage applied between terminals 1C-7 and 1E-2
Below 1 Ω
1C-4 - 1B-1
1C-9 - 1B-1
1C-10 - 1B-1

EFI MAIN2 RELAY (NO. 1 INTEGRATION RELAY) 
Standard Resistance
1A-6 - 1D-1
Battery voltage not applied between terminals 1A-8 and 1E-2
10 kΩ or higher
1A-6 - 1D-1
Battery voltage applied between terminals 1A-8 and 1E-2
Below 1 Ω
1A-7 - 1D-1
1C-6 - 1D-1

IG2 RELAY (NO. 1 INTEGRATION RELAY) 
Standard Resistance
1A-1 - 1D-3
Battery voltage not applied between terminals 1C-8 and 1E-2
10 kΩ or higher
1A-1 - 1D-3
Battery voltage applied between terminals 1C-8 and 1E-2
Below 1 Ω
1A-3 - 1D-3
1C-1 - 1D-3
1C-2 - 1D-3
1C-5 - 1D-3

EDU RELAY (EDU) 
Standard Resistance
3 - 5
Battery voltage not applied between terminals 1 and 2
10 kΩ or higher
Battery voltage applied between terminals 1 and 2
Below 1 Ω