Home › Engine / Hybrid System ยท 6AR-FSE › ENGINE CONTROL › CAMSHAFT OIL CONTROL SOLENOID

CAMSHAFT OIL CONTROL SOLENOID > INSTALLATION

for Preparation Click here



1. INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY


    A332562E01
  1. Apply engine oil to a new O-ring and install it to the camshaft timing oil control solenoid assembly as shown in the illustration.
    Text in Illustration 
    *1
    O-ring

    NOTICE:
    Do not damage the O-ring.



    A192239E21
  1. Apply adhesive to 2 or 3 threads of 2 new bolts.
    Text in Illustration 
    *a
    Adhesive 1324

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.

  1. Install the camshaft timing oil control solenoid assembly to the timing chain cover sub-assembly with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    1. If the camshaft timing oil control solenoid assembly has been struck or dropped, replace it.
    2. Make sure that the O-ring is not cracked or moved out of place when installing the camshaft timing oil control solenoid assembly.

  1. Connect the camshaft timing oil control solenoid assembly connector.



2. INSTALL ENGINE MOVING CONTROL ROD BRACKET


  1. When replacing the engine moving control rod.



      A338527E01
    1. Install the engine moving control rod bracket with engine moving control rod with the 4 bolts.

      Torque:
      38 N*m{ 387 kgf*cm , 28 ft.*lbf }

      NOTICE:
      Temporarily tighten bolt (A) and bolt (B), and then fully tighten the 4 bolts in the order of bolt (D), bolt (C), bolt (A) and bolt (B).



    2. A348191E01
    3. Using SST and a union nut wrench (14 mm), tighten the bolt.
      Text in Illustration 
      *a
      Torque Wrench Fulcrum Length
      *b
      Union Nut Wrench

      SST
      09961-00950  

      Torque:
      Specified Tightening Torque:
      52 N*m{ 530 kgf*cm , 38 ft.*lbf }

      NOTICE:
      1. Calculate the torque wrench reading when changing the fulcrum length of the torque wrench (Click here).
      2. When using SST (fulcrum length of 150 mm (5.91 in.)) + torque wrench (fulcrum length of 260 mm (10.2 in.)): 33 N*m (337 kgf*cm, 24 ft.*lbf)



  1. When not replacing the engine moving control rod.



      A338527E01
    1. Install the engine moving control rod bracket with engine moving control rod with the 4 bolts.

      Torque:
      38 N*m{ 387 kgf*cm , 28 ft.*lbf }

      NOTICE:
      Temporarily tighten bolt (A) and bolt (B), and then fully tighten the 4 bolts in the order of bolt (D), bolt (C), bolt (A) and bolt (B).



3. INSTALL NO. 2 ENGINE MOUNTING STAY RH
  1. Install the No. 2 engine mounting stay RH with the 2 bolts.

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }



4. INSTALL EARTH WIRE
  1. Install the earth wire with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



5. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY
  1. Engage the 3 grommets to install the No. 1 engine cover sub-assembly.