Home › Engine / Hybrid System ยท 2AR-FE › EMISSION CONTROL › CANISTER (for TMMK Made)

CANISTER (for TMMK Made) > ON-VEHICLE INSPECTION

for Preparation Click here



1. INSPECT CANISTER (FUEL SUCTION PLATE SUB-ASSEMBLY) (for Fuel Tank Cap Method)
  1. Inspect evaporative emission control system .



  1. Check for clogs in the air filter (when not using the GTS).

    1. Start the engine.

    2. Warm up the engine.

    3. Allow the engine to idle for 15 minutes.

    4. Open the fuel tank cap assembly to discharge the pressure in the fuel tank assembly.

    5. Close the fuel tank cap assembly and allow the engine to idle for 30 seconds.



    6. A202994
    7. Open the fuel tank cap assembly and check for inhalation sounds.

      OK:
      No whooshing sounds (inhalation sound) are heard.

      HINT:
      If there is a smell of gasoline and a whooshing sound (exhalation sound) is heard, positive pressure in the fuel tank assembly is being discharged. This is not indicate a malfunction.

  1. Check for clogs in the air filter (when using the GTS).

    1. Connect the GTS to the DLC3.

    2. Start the engine.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.

    5. Open the fuel tank cap assembly to discharge the pressure in the fuel tank assembly.

    6. Perform the Active Test "Activate the VSV for Evap Control" while the engine is idling.

    7. Close the fuel tank cap assembly and allow the engine to idle for 30 seconds.

    8. Open the fuel tank cap assembly and check for inhalation sounds.

      OK:
      No whooshing sounds (inhalation sound) are heard.

      HINT:
      If there is a smell of gasoline and a whooshing sound (exhalation sound) is heard, positive pressure in the fuel tank assembly is being discharged. This is not indicate a malfunction.



2. INSPECT CANISTER (FUEL SUCTION PLATE SUB-ASSEMBLY) (for Vacuum Measurement Method)
  1. Visually check the canister (fuel suction plate sub-assembly) for airtightness.

    1. Visually check the canister (fuel suction plate sub-assembly) for cracks or damage, and check that there is no smell of gasoline.



  1. Inspect the ventilation of the canister (fuel suction plate sub-assembly).

    NOTICE:
    When inspecting with parts installed to the vehicle, be sure to remove the fuel tank cap assembly.




      A315160E03
    1. Apply compressed air to the port (A) and check that the air flows from the port (B).
      Text in Illustration 
      *a
      Port (A)
      *b
      Port (B)
      *c
      Air

      OK:
      Air flows from the port (B).



  1. Inspect the check valve.

    NOTICE:
    When inspecting with parts installed to the vehicle, be sure to remove the fuel tank cap assembly.




      A315161E01
    1. Close the port (A) and apply compressed air to the port (B).
      Text in Illustration 
      *a
      Port (A)
      *b
      Port (B)
      *c
      Air

      OK:
      Air does not flow at first. By gradually increasing the pressure, air flows when the pressure in the port reaches a certain level.



    2. A315162E01
    3. Using a vacuum pump, apply vacuum to the port (B) with the port (A) closed.
      Text in Illustration 
      *a
      Port (A)
      *b
      Port (B)
      *c
      Vacuum Pump

      OK:
      The vacuum is maintained at first. By gradually increasing the vacuum, air flows and the level of vacuum is maintained after the vacuum reaches a certain level.



  1. Check for clogs in the air filter (when not using the GTS).



      A347171E01
    1. Connect the fuel hose to the canister (fuel suction plate sub-assembly) via the 3-way connector, hose and vacuum pump as shown in the illustration.
      Text in Illustration 
      *1
      Fuel Hose
      *a
      3-way Connector
      *b
      Hose
      *c
      Vacuum Pump

    2. Start the engine.

    3. Warm up the engine.

    4. Allow the engine to idle for 15 minutes.

    5. Check the indicator needle of the vacuum pump.

      OK:
      The indicator needle of the vacuum pump does not rise from its initial position.

      HINT:
      The indicator needle may shake due to engine vibration, etc., but if it immediately returns to its initial position, there is no problem.



  1. Check for clogs in the air filter (when using the GTS).

    1. Connect the fuel hose to the canister (fuel suction plate sub-assembly) via the 3-way connector, hose and vacuum pump as shown in the illustration.



    2. A347171E01
    3. Connect the GTS to the DLC3.
      Text in Illustration 
      *1
      Fuel Hose
      *a
      3-way Connector
      *b
      Hose
      *c
      Vacuum Pump

    4. Start the engine.

    5. Turn the GTS on.

    6. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.

    7. Perform the Active Test "Activate the VSV for Evap Control" while the engine is idling.

    8. Check the indicator needle of the vacuum pump.

      OK:
      The indicator needle of the vacuum pump does not rise from its initial position.

      HINT:
      The indicator needle may shake due to engine vibration, etc., but if it immediately returns to its initial position, there is no problem.