Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM

DTC    B1571    Green LED Error

for Preparation Click here


DESCRIPTION

This DTC is stored when the telematics transceiver detects an open or short in the manual (SOS) switch indicator (green) circuit of the manual (SOS) switch. The manual (SOS) switch indicator (green) illuminates after the ignition switch is turned to ON. If the telematics system is not active, the manual (SOS) switch indicator (green) will turn off. If the telematics system is active, the manual (SOS) switch indicator (green) will blink while communicating with the call center.

DTC No.
DTC Detection Condition
Trouble Area
B1571
Current for the manual (SOS) switch indicator (green) exceeds malfunction threshold for 20 seconds when the ignition switch is ON.
  1. Telematics transceiver
  2. Roof console box assembly (manual (SOS) switch)
  3. Wire harness or connector

WIRING DIAGRAM


E342832E02


INSPECTION PROCEDURE

NOTICE:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System (Click here).

1.CHECK DTC
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and wait for 20 seconds.

  1. Turn the GTS on.

  1. Check for DTCs and check that no DTCs are output (Click here).

    OK:
    No DTCs are output.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.INSPECT ROOF CONSOLE BOX ASSEMBLY (MANUAL (SOS) SWITCH) (INPUT VOLTAGE)


    B234642E38
  1. Measure the voltage according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    17 (IND2) - 11 (GND3)
    2 seconds after ignition switch turned ON → Ignition switch off
    8.5 to 10 V → Below 1 V

    Text in Illustration 
    *a
    Component with harness connected
    (Roof Console Box Assembly (Manual (SOS) Switch)



NG
Go to step 4
OK


3.INSPECT ROOF CONSOLE BOX ASSEMBLY (MANUAL (SOS) SWITCH) (GREEN INDICATOR)


    B129570E57
  1. Remove the roof console box assembly (manual (SOS) switch) (Click here).

  1. Connect 2 dry-cell batteries (1.5 V each) in series.

  1. Connect a positive (+) lead from the batteries to terminal 17 (IND2) and a negative (-) lead to terminal 11 (GND3) of the roof console box assembly (manual (SOS) switch) connector.

  1. Check if the manual (SOS) switch indicator (green) illuminates.

    OK:
    Manual (SOS) switch indicator (green) illuminates.

    Text in Illustration 
    *a
    Component without harness connected
    (Roof Console Box Assembly (Manual (SOS) Switch)



NG
REPLACE ROOF CONSOLE BOX ASSEMBLY (MANUAL (SOS) SWITCH) (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - ROOF CONSOLE BOX ASSEMBLY)
  1. Disconnect the I218 telematics transceiver connector.

  1. Disconnect the S7 roof console box assembly (manual (SOS) switch) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I218-12 (IND2) - S7-17 (IND2)
    Always
    Below 1 Ω
    I218-12 (IND2) or S7-17 (IND2) - Body ground
    Always
    10 kΩ or higher
    I218-26 (SIG-) - S7-11 (GND3)
    Always
    Below 1 Ω
    I218-26 (SIG-) or S7-11 (GND3) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE TELEMATICS TRANSCEIVER
  1. Replace the telematics transceiver with a new one (Click here).


NEXT

PERFORM REGISTRATION (Click here)