Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM

DTC    B1572    Microphone Error

for Preparation Click here


DESCRIPTION

This DTC is stored when a microphone signal line is disconnected.

DTC No.
DTC Detection Condition
Trouble Area
B1572
Current at terminal MCVD exceeds the malfunction threshold for 20 seconds while the ignition switch is ON.
  1. Telematics transceiver
  2. Roof console box assembly (telephone microphone assembly)
  3. Wire harness or connector

WIRING DIAGRAM


E342822E03


INSPECTION PROCEDURE

NOTICE:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System (Click here).

1.CHECK DTC
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and wait for 20 seconds.

  1. Turn the GTS on.

  1. Check for DTCs and check that no DTCs are output (Click here).

    OK:
    No DTCs are output.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.INSPECT TELEMATICS TRANSCEIVER


    E338312E01
  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    33 (MCVD) - Body ground
    Ignition switch ACC
    4 to 6 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    35 (MCI-) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Telematics Transceiver)



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEVIER - ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
  1. Disconnect the I218 telematics transceiver connector.

  1. Disconnect the S7 roof console box assembly (telephone microphone assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I218-33 (MCVD) - S7-14 (MACC)
    Always
    Below 1 Ω
    I218-34 (MCI+) - S7-13 (MCO+)
    Always
    Below 1 Ω
    I218-35 (MCI-) - S7-12 (MCO-)
    Always
    Below 1 Ω
    I218-33 (MCVD) or S7-14 (MACC) - Body ground
    Always
    10 kΩ or higher
    I218-34 (MCI+) or S7-13 (MCO+) - Body ground
    Always
    10 kΩ or higher
    I218-35 (MCI-) or S7-12 (MCO-) - Body ground
    Always
    10 kΩ or higher
    I218-32 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)


    B129570E58
  1. Remove the roof console box assembly (telephone microphone assembly) (Click here).

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    14 (MACC) - 12 (MCO-)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Roof Console Box Assembly (Telephone Microphone Assembly))



NG
REPLACE ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) (Click here)
OK


5.REPLACE TELEMATICS TRANSCEIVER
  1. Replace the telematics transceiver with a new one (Click here).


NEXT

PERFORM REGISTRATION (Click here)