Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM

DTC    B15C0    GPS Antenna Disconnected (Short)

DTC    B15C1    GPS Antenna Disconnected (Open)

for Preparation Click here


DESCRIPTION

These DTCs are stored when a malfunction occurs in the telephone antenna assembly.

DTC No.
DTC Detection Condition
Trouble Area
B15C0
Current to the telephone antenna assembly is lower than the malfunction threshold for 20 seconds when the ignition switch is ON. (Short circuit)
  1. Telematics transceiver
  2. Antenna divider*
  3. Telephone antenna assembly
  4. Wire harness or connector
B15C1
Current for telephone antenna assembly is higher than the malfunction threshold for 20 seconds when the ignition switch is ON. (Open circuit)
  1. Telematics transceiver
  2. Antenna divider*
  3. Telephone antenna assembly
  4. Wire harness or connector
  1. *: w/ Navigation System

WIRING DIAGRAM


w/ Navigation System

E360085E01


w/o Navigation System

E360069E04


INSPECTION PROCEDURE

NOTICE:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System (Click here).

1.CHECK DTC
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and wait for 20 seconds.

  1. Turn the GTS on.

  1. Check for DTCs and check that no DTCs are output (Click here).

    OK:
    No DTCs are output.

    Result:
    Result
    Proceed to
    OK (w/ Navigation System)
    A
    OK (w/o Navigation System)
    B
    NG
    C



B
Go to step 4

C
USE SIMULATION METHOD TO CHECK (Click here)
A


2.CHECK HARNESS AND CONNECTOR
  1. Disconnect the O47 telephone antenna assembly connector.

  1. Disconnect the I219 antenna divider connector.

  1. Disconnect the I220 telematics transceiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O47-2 (GPSD1) - I219-6 (GPS1)
    Always
    Below 1 Ω
    I220-1 (GPSD2) - I219-5 (GPSD1)
    Always
    Below 1 Ω
    O47-2 (GPSD1) or I219-6 (GPS1) - Body ground
    Always
    10 kΩ or higher
    I220-1 (GPSD2) or I219-5 (GPSD1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT ANTENNA DIVIDER
  1. Remove the Antenna divider (Click here).



    E241596E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (GPSN1) - 6 (GPS1)
    Always
    10 kΩ or higher
    5 (GPSD1) - 6 (GPS1)
    Always
    Below 1 Ω
    5 (GPSD1) - 5a
    Always
    10 kΩ or higher
    6 (GPS1) - 6a
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Antenna Divider)



NG
REPLACE ANTENNA DIVIDER (Click here)
OK


Go to step 5

4.CHECK HARNESS AND CONNECTOR
  1. Disconnect the O47 telephone antenna assembly connector.

  1. Disconnect the O48 telematics transceiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O47-2 (GPS1) - O48-1 (GPSD2)
    Always
    Below 1 Ω
    O47-2 (GPS1) or O48-1 (GPSD2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE TELEPHONE ANTENNA ASSEMBLY
  1. Replace the telephone antenna assembly with a new or known good one (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check that no DTCs are output.



NG
Go to step 6
OK

END 

6.REPLACE TELEMATICS TRANSCEIVER
  1. Replace the telematics transceiver with a new one (Click here).


NEXT

PERFORM REGISTRATION (Click here)