Home › Vehicle Exterior › BODY PANEL › FRONT BODY PILLAR(for Type A)
BM33A0E _01 Vehicle Exterior _067228 BODY PANEL _0327721 FRONT BODY PILLAR(for Type A) F

BODY PANEL  FRONT BODY PILLAR(for Type A)  CUT AND JOIN REPLACEMENT SECTIONS (PATTERN 2)  


K140655

With the cowl top side upper panel assembly, center body pillar cut and join replacement section and roof panel assembly removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points
K108828

Cut Location for Supply Parts

a.

Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)


b.

Remove the front body pillar upper outer.

K140291C03
2.323,2.094 1.74,1.042 1.74,1.042 1.323,1.042 false 1.135,0.938 1.448,1.094 0.313,0.156 10 false *1
*1 FRONT BODY PILLAR UPPER OUTER - -
K111603

Laser Screw Welding - -


K140292

K140293

K140294C04
0.25,0.25 0.563,0.406 0.313,0.156 10 false *A
*A except Panoramic Moon Roof - -


K141416C02
0.25,0.25 0.563,0.406 0.313,0.156 10 false *A
*A for Panoramic Moon Roof - -



c.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K140295C05
0,0 0,0 false
K108837

Adhesive - -



d.

Remove the front body pillar reinforce sub-assembly lower and roof side rail.


e.

A indicates welds to remove for easier removal.

K140296C03
3.073,1.542 2.469,0.677 2.469,0.677 2.104,0.677 false 3.365,3.531 2.99,3.531 2.99,3.531 2.542,3.781 false 1.896,0.573 2.208,0.729 0.313,0.156 10 false *1 3.427,3.458 3.74,3.615 0.313,0.156 10 false *2
*1 ROOF SIDE RAIL *2 FRONT BODY PILLAR REINFORCE SUB-ASSEMBLY LOWER
K111603

Laser Screw Welding - -


K140297

K140298


f.

When replace only the outer panel, please cut off a necessary range depending on a damage range.

i.

Carefully cut the outer panel so not to damage the reinforcement.


ii.

Make sure that butt welding does not heat-affect the reinforcement when welding the outer panel.




INSTALLATION


Symbol Meaning
K108821

Spot Weld
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld
K108831

Butt Weld
K108834

Body Sealer

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

Before temporarily installing the new parts, weld the front body pillar reinforce sub-assembly lower and roof side rail with the standard number of welding points.

K140299C03
4.5,1.427 4.125,1.427 4.125,1.427 3.75,1 false 3.906,2.729 3.604,2.729 3.604,2.729 3.104,2.365 false 4.542,1.344 4.854,1.5 0.313,0.156 10 false *1 3.958,2.646 4.271,2.802 0.313,0.156 10 false *2
*1 ROOF SIDE RAIL *2 FRONT BODY PILLAR REINFORCE SUB-ASSEMBLY LOWER



d.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Apply a light coat of adhesive around the plug welding points.

·

Apply enough adhesive to the panels.



K140295C04
0,0 0,0 false
K108837

Adhesive - -



e.

Weld the front body pillar reinforce sub-assembly lower and roof side rail to the vehicle side.

K140300C03
4.917,2.563 4.531,2.563 4.531,2.563 3.927,1.469 false 2.563,3.656 3.688,3.313 3.688,3.313 4.094,3.313 false 4.969,2.469 5.281,2.625 0.313,0.156 10 false *1 4.146,3.229 4.458,3.385 0.313,0.156 10 false *2
*1 ROOF SIDE RAIL *2 FRONT BODY PILLAR REINFORCE SUB-ASSEMBLY LOWER
*a Ultra High Strength Steel Welding Point *b Ultra High Strength Steel Welding Point
K111603

Laser Screw Welding - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 1500 MPa ultra high strength steel.

*a: Spot weld Pressure 2940 N (300 kgf, 661 lbf)
Weld current 10000 A
Weld time 16 Cyc.(0.27 Sec.)
*b: Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.



K140301C03
0,0 0,0 false
*a Ultra High Strength Steel Welding Point *b Ultra High Strength Steel Welding Point


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 1500 MPa ultra high strength steel.

*a: Spot weld Pressure 2940 N (300 kgf, 661 lbf)
Weld current 10000 A
Weld time 16 Cyc.(0.27 Sec.)
*b: Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.



K140307C02
0,0 0,0 false
*a Ultra High Strength Steel Welding Point - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 1180 MPa ultra high strength steel.

*a: Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.



K140302


f.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K140303


g.

Weld the front body pillar upper outer to the vehicle side.

K140304C03
2.552,2.938 3.063,2.719 3.063,2.719 3.823,2.719 false 3.865,2.635 4.177,2.792 0.313,0.156 10 false *1
*1 FRONT BODY PILLAR UPPER OUTER - -
*a Ultra High Strength Steel Welding Point - -
K111603

Laser Screw Welding - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 3 panels or more together including 1500 MPa ultra high strength steel. (When plug welding a third panel to 2 panels which are welded under the conditions described above.)

*a: Plug weld Plug diameter Same as the standard method (See the introduction)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.



K140305C03
0.25,0.25 0.563,0.406 0.313,0.156 10 false *A
*A except Panoramic Moon Roof - -
*a Ultra High Strength Steel Welding Point - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 3 panels or more together including 1500 MPa ultra high strength steel. (When plug welding a third panel to 2 panels which are welded under the conditions described above.)

*a: Plug weld Plug diameter Same as the standard method (See the introduction)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.



K141418C03
0.25,0.25 0.563,0.406 0.313,0.156 10 false *A
*A for Panoramic Moon Roof - -
*a Ultra High Strength Steel Welding Point - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 3 panels or more together including 1500 MPa ultra high strength steel. (When plug welding a third panel to 2 panels which are welded under the conditions described above.)

*a: Plug weld Plug diameter Same as the standard method (See the introduction)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.



K140306


h.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)


i.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


j.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.