Home › General › INTRODUCTION › WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS › 2018.04–2020.02
BM33A0E _V1 General _067231 INTRODUCTION _0327766 WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS F

INTRODUCTION  WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS  WHEEL ALIGNMENT STANDARD  


The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after completing the front wheel alignment procedure are shown below.

Necessary Procedures After Procedure Performed
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated



MEASURE VEHICLE HEIGHT


NOTICE:
·

Before inspecting the wheel alignment, adjust the vehicle height to the specified value.

·

Be sure to perform measurement on a level surface.

·

If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.

·

Inspect while the vehicle is unloaded.

·

The standard value shown here is a value that is used for performing a wheel alignment and does not indicate the height of an actual vehicle.



a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.
C370166N01
0.844,1.125 1,1.323 0.156,0.198 10 false A 2.406,1.198 2.563,1.396 0.156,0.198 10 false B 0.813,3.99 0.969,4.188 0.156,0.198 10 false C 2.375,4.031 2.531,4.229 0.156,0.198 10 false D

Measure the vehicle height.

Measurement Points:

A: Ground clearance of front wheel center


B: Ground clearance of center of bolt head of front lower No. 2 suspension arm bushing (rear bolt of front lower No. 1 suspension arm sub-assembly).


C: Ground clearance of rear wheel center


D: Ground clearance of center of bolt head of rear No. 2 suspension arm assembly and rear suspension member sub-assembly.


Vehicle Height (Unloaded Vehicle):
Engine SUSPENSION TYPE Front A - B Rear C - D

*: for Rough Road Area Specification Vehicles

2AR-FE
A25A-FKS
6AR-FSE
NORMAL 150 mm (5.91 in.)
138 mm (5.43 in.)*
49 mm (1.93 in.)
38 mm (1.50 in.)*
SPORT 150 mm (5.91 in.) 46 mm (1.81 in.)
2GR-FKS NORMAL 155 mm (6.10 in.)
140 mm (5.51 in.)*
53 mm (2.09 in.)
41 mm (1.61 in.)*
SPORT 152 mm (5.98 in.) 49 mm (1.93 in.)




INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION (FRONT WHEEL ALIGNMENT)


NOTICE:

Inspect while the vehicle is unloaded.


a.
C132440C16
2.396,1.104 2.51,0.823 2.51,0.823 2.74,0.823 false 0.604,0.708 1.031,0.708 1.031,0.708 1.031,1.458 false 2.76,0.729 2.99,0.906 0.229,0.177 10 false *b 0.448,0.604 0.688,0.781 0.24,0.177 10 false *a
*a Turning Radius Gauge
*b Camber-caster-kingpin Gauge


Install a camber-caster-kingpin gauge and place the front wheels on the center of a turning radius gauge.


b.

Inspect the camber, caster and steering axis inclination.

Camber (Unloaded Vehicle):
Engine SUSPENSION TYPE Camber Inclination Right-left Difference

*: for Rough Road Area Specification Vehicles

2AR-FE
A25A-FKS
6AR-FSE
NORMAL -0°30' +/- 0°45' (-0.50° +/- 0.75°)
-0°20' +/- 0°45' (-0.33° +/- 0.75°)*
0°45' (0.75°) or less
SPORT -0°30' +/- 0°45' (-0.50° +/- 0.75°)
2GR-FKS NORMAL -0°35' +/- 0°45' (-0.58° +/- 0.75°)
-0°25' +/- 0°45' (-0.42° +/- 0.75°)*
SPORT -0°30' +/- 0°45' (-0.50° +/- 0.75°)


Caster (Unloaded Vehicle):
Engine SUSPENSION TYPE Caster Inclination Right-left Difference

*: for Rough Road Area Specification Vehicles

2AR-FE
A25A-FKS
6AR-FSE
NORMAL 5°20' +/- 0°45' (5.33° +/- 0.75°)
5°15' +/- 0°45' (5.25° +/- 0.75°)*
0°45' (0.75°) or less
SPORT 5°20' +/- 0°45' (5.33° +/- 0.75°)
2GR-FKS NORMAL 5°20' +/- 0°45' (5.33° +/- 0.75°)
5°15' +/- 0°45' (5.25° +/- 0.75°)*
SPORT 5°20' +/- 0°45' (5.33° +/- 0.75°)


Steering Axis Inclination (Unloaded Vehicle):
Engine SUSPENSION TYPE Steering Axis Inclination Reference

*: for Rough Road Area Specification Vehicles

2AR-FE
A25A-FKS
6AR-FSE
NORMAL 12°55' (12.92°)
12°35' (12.58°)*
SPORT 12°55' (12.92°)
2GR-FKS NORMAL 13°00' (13.00°)
12°40' (12.67°)*
SPORT 13°00' (13.00°)




INSPECT TOE-IN (FRONT WHEEL ALIGNMENT)


NOTICE:

Inspect while the vehicle is unloaded.


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to N.


c.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step C)


d.
C188968C01
0.833,0.583 0.833,1.115 false 1.365,0.583 1.365,0.99 1.365,0.99 0.833,0.99 false 2.521,1.333 2.521,1.667 false 0.74,1.135 0.917,1.302 0.177,0.167 10 *a 2.427,1.698 2.604,1.854 0.177,0.156 10 *b
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).


e.

Slowly push the vehicle straight ahead to cause the front wheels to rotate 180°. Use the front tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from step C again.



f.
C188969C01
0.646,1.271 0.646,1.635 false 1.917,0.542 2.052,0.698 0.135,0.156 10 C 3.073,0.552 3.208,0.708 0.135,0.156 10 D 2.5,0.719 2.635,0.875 0.135,0.156 10 A 2.51,1.542 2.646,1.698 0.135,0.156 10 B 0.563,1.656 0.74,1.813 0.177,0.156 10 *a
*a Dimension A
V100135

Front of the Vehicle


Measure the distance between the tread center marks on the front of the wheels (dimension A).

Toe-in (Unloaded Vehicle):
Engine SUSPENSION TYPE Specified Condition

*: for Rough Road Area Specification Vehicles

2AR-FE
A25A-FKS
6AR-FSE
NORMAL C + D: 0°09' +/- 0°10' (0.15° +/- 0.17°)
C + D: 0°09' +/- 0°10' (0.15° +/- 0.17°)*
B - A: 1.7 +/- 2.0 mm (0.0669 +/- 0.0787 in.)
B - A: 1.8 +/- 2.0 mm (0.0709 +/- 0.0787 in.)*
SPORT C + D: 0°09' +/- 0°10' (0.15° +/- 0.17°)
B - A: 1.7 +/- 2.0 mm (0.0669 +/- 0.0787 in.)
2GR-FKS NORMAL C + D: 0°06' +/- 0°10' (0.09° +/- 0.17°)
C + D: 0°09' +/- 0°10' (0.15° +/- 0.17°)*
B - A: 1.1 +/- 2.0 mm (0.0433 +/- 0.0787 in.)
B - A: 1.7 +/- 2.0 mm (0.0669 +/- 0.0787 in.)*
SPORT C + D: 0°07' +/- 0°10' (0.12° +/- 0.17°)
B - A: 1.4 +/- 2.0 mm (0.0551 +/- 0.0787 in.)


HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, adjust it at the steering rack ends.



INSPECT WHEEL ANGLE (FRONT WHEEL ALIGNMENT)


a.
C132439C03
0.863,0.204 1.036,0.381 0.173,0.177 10 *b 0.538,0.204 0.713,0.381 0.176,0.177 10 *a 2.397,0.204 2.57,0.381 0.173,0.177 10 *b 2.725,0.204 2.901,0.381 0.176,0.177 10 *a
*a Inside
*b Outside
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of a turning radius gauge.


b.

Turn the steering wheel fully to the left and right and measure the turning angle.

NOTICE:

Inspect while the vehicle is unloaded.


If the right and left inside wheel angles differ from the specified value, check and adjust the right and left steering rack end lengths.


Wheel Turning Angle (Unloaded Vehicle):
Engine SUSPENSION TYPE Tire Size Inside Wheel Outside Wheel

*: for Rough Road Area Specification Vehicles

2AR-FE
A25A-FKS
6AR-FSE
NORMAL 205/65R16
215/55R17
38°10' +/- 2°00' (38.17° +/- 2.00°)
38°30' +/- 2°00' (38.50° +/- 2.00°)*
32°45' (32.75°)
33°00' (33.00°)*
235/45R18 36°50' +/- 2°00' (36.83° +/- 2.00°)
37°20' +/- 2°00' (37.33° +/- 2.00°)*
31°50' (31.83°)
32°15' (32.25°)*
SPORT - 36°50' +/- 2°00' (36.83° +/- 2.00°) 31°55' (31.92°)
2GR-FKS NORMAL 215/55R17 38°25' +/- 2°00' (38.42° +/- 2.00°)* 33°00' (33.00°)*
235/45R18 36°45' +/- 2°00' (36.75° +/- 2.00°)
37°05' +/- 2°00' (37.08° +/- 2.00°)*
31°45' (31.75°)
32°05' (32.08°)*
SPORT - 36°50' +/- 2°00' (36.83° +/- 2.00°) 31°50' (31.83°)




INSPECT CAMBER (REAR WHEEL ALIGNMENT)


NOTICE:

Inspect while the vehicle is unloaded.


a.
C107736C10
2.052,1.26 2.375,1.26 false 2.406,1.167 2.656,1.385 0.25,0.219 10 *a
*a Camber-caster-kingpin Gauge


Install a camber-caster-kingpin gauge.


b.

Inspect the camber.

Camber (Unloaded Vehicle):
Engine SUSPENSION TYPE Camber Inclination Right-left Difference

*: for Rough Road Area Specification Vehicles

2AR-FE
A25A-FKS
6AR-FSE
NORMAL -1°10' +/- 0°45' (-1.17° +/- 0.75°)
-0°55' +/- 0°45' (-0.92° +/- 0.75°)*
0°45' (0.75°) or less
SPORT -1°05' +/- 0°45' (-1.08° +/- 0.75°)
2GR-FKS NORMAL -1°10' +/- 0°45' (-1.17° +/- 0.75°)
-1°00' +/- 0°45' (-1.00° +/- 0.75°)*
SPORT -1°10' +/- 0°45' (-1.17° +/- 0.75°)


HINT:

Camber is not adjustable. If the measurement is not within the specified range, inspect the suspension parts for damage and/or wear, and replace them if necessary.




INSPECT TOE-IN (REAR WHEEL ALIGNMENT)


NOTICE:

Inspect while the vehicle is unloaded.


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to N.


c.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)


d.
C188968C02
0.83,0.579 0.83,1.114 false 1.361,0.579 1.361,0.992 1.361,0.992 0.83,0.992 false 0.739,1.134 0.912,1.302 0.173,0.168 10 *a 2.432,1.697 2.607,1.858 0.176,0.161 10 *b 2.522,1.33 2.522,1.671 false
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).


e.

Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180°. Use the rear tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from step A again.



f.
C188969C02
0.646,1.271 0.646,1.635 false 1.917,0.542 2.052,0.698 0.135,0.156 10 C 3.073,0.552 3.208,0.708 0.135,0.156 10 D 2.5,0.719 2.635,0.875 0.135,0.156 10 A 2.51,1.542 2.646,1.698 0.135,0.156 10 B 0.563,1.656 0.74,1.813 0.177,0.156 10 *a
*a Dimension A
V100135

Front of the Vehicle


Measure the distance between the tread center marks on the front of the rear wheels (dimension A).

Toe-in (Unloaded Vehicle):
Engine SUSPENSION TYPE Specified Condition Right-left Difference

*: for Rough Road Area Specification Vehicles

2AR-FE
A25A-FKS
6AR-FSE
NORMAL C + D: 0°10' +/- 0°10' (0.16° +/- 0.17°)
C + D: 0°09' +/- 0°10' (0.15° +/- 0.17°)*
-
B - A: 1.9 +/- 2.0 mm (0.0748 +/- 0.0787 in.)
B - A: 1.8 +/- 2.0 mm (0.0709 +/- 0.0787 in.)*
2.0 mm (0.0787 in.) or less
SPORT C + D: 0°09' +/- 0°10' (0.15° +/- 0.17°) -
B - A: 1.7 +/- 2.0 mm (0.0669 +/- 0.0787 in.) 2.0 mm (0.0787 in.) or less
2GR-FKS NORMAL C + D: 0°12' +/- 0°10' (0.20° +/- 0.17°)
C + D: 0°11' +/- 0°10' (0.18° +/- 0.17°)*
-
B - A: 2.3 +/- 2.0 mm (0.0906 +/- 0.0787 in.)
B - A: 2.1 +/- 2.0 mm (0.0827 +/- 0.0787 in.)*
2.0 mm (0.0787 in.) or less
SPORT C + D: 0°10' +/- 0°10' (0.16° +/- 0.17°) -
B - A: 1.9 +/- 2.0 mm (0.0748 +/- 0.0787 in.) 2.0 mm (0.0787 in.) or less


HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, adjust it at the rear suspension toe adjust cam sub-assembly.