FUNCTION OF MAIN COMPONENTS
The main components in the cruise control system have the following functions:
| Component | Function | |
|---|---|---|
|
*: Models with shift paddle switch (transmission shift switch assembly) |
||
| Steering Pad Switch Assembly | Cruise Control Switch | Turns the cruise control system on and off. |
| CANCEL Switch | A cancel signal is output to the ECM when this switch is operated. | |
| +RES Switch | The accelerate function and resuming of a preset speed can be performed by operating this switch. A signal is output to the ECM when this switch is operated. | |
| -SET Switch | The decelerate function and vehicle speed setting signals are output to the ECM when this switch is operated. | |
| Brake Actuator Assembly | Skid Control ECU | ·
Transmits the wheel speed signal to the ECM. ·
Transmits the VSC operation signal to the ECM. |
| ECM | ·
Controls all functions of the cruise control system in accordance with the signals from switches, sensors and ECUs. ·
If the ECM detects a malfunction in the cruise control system, it will store a Diagnostic Trouble Code (DTC). |
|
| Combination Meter Assembly | Cruise Control Indicator | ·
Based on a cruise control indicator operation signal sent by the ECM, the combination meter assembly illuminates the cruise control indicator when the cruise control system has been turned on using the cruise control switch on the steering pad switch assembly. ·
Based on a cruise control indicator operation signal sent by the ECM, the combination meter assembly turns off the cruise control indicator if a malfunction occurs in the cruise control system. |
| Cruise SET Indicator | Cruise SET indicator illuminates when the vehicle speed is set. | |
| Multi-information Display | Displays a warning message to alert the driver in accordance with a signal received from the ECM. | |
| Master Warning Light | Comes on when there is a malfunction in the system. | |
| Buzzer | If the ECM detects automatic cancel or warning signals while the vehicle is operating under cruise control, this buzzer sounds to inform the driver. | |
| Throttle Body with Motor Assembly | Throttle Control Motor | Adjusts the throttle valve opening angle in accordance with signals from the ECM. |
| Throttle Position Sensor | Detects the throttle valve opening angle and outputs it to the ECM. | |
| Speed Sensor | Detects the wheel speed and transmits signals to the skid control ECU. | |
| Accelerator Pedal Sensor Assembly | Detects the accelerator pedal depression angle and transmits it to the ECM. | |
| Park/Neutral Position Switch Assembly | Detects the shift lever position and transmits signals to the ECM. | |
| VSC OFF Switch | Detects the VSC OFF (TRC OFF) signals and outputs it to the skid control ECU. | |
| Shift Lock Control Unit Assembly | Transmission Control Switch | ·
Detects the shift lever position and transmits signals to the ECM. ·
Informs the ECM of driver upshift or downshift operations while the shift lever is in S. |
| Stop Light Switch Assembly | Detects the brake pedal being depressed and transmits its signal to the ECM. | |
| Shift Paddle Switch (Transmission Shift Switch Assembly)* | While the vehicle is being driven in D mode or S mode, this switch outputs a signal to the ECM when the switch is pulled to "+" or "-". | |
| Central Gateway ECU (Network Gateway ECU) | Gateway function of CAN communication. | |
FUNCTION
The cruise control system has the following control functions:
| Function | Outline |
|---|---|
|
*: Models with shift paddle switch (transmission shift switch assembly) |
|
| Constant Speed Control | The ECM compares the actual vehicle speed and the set speed and if the vehicle speed is lower than the set speed, it uses the throttle control motor to increase the throttle valve opening angle. |
| Set Control | When this system fulfils the following conditions, and the -SET switch on the steering pad switch assembly is pressed and released, the ECM stores the vehicle speed and maintains the vehicle constantly at that speed.
·
The cruise control system has been turned on using the cruise control switch on the steering pad switch assembly. ·
The vehicle is being driven at a speed of approximately 40 km/h (25 mph) to 200 km/h (125 mph). |
| Low Speed Limit Control | The low speed limit is the lowest speed that cruise control can be set at and it is designed to be approximately 40 km/h (25 mph). The cruise control system cannot be set below that speed. If the vehicle speed drops below that speed while the cruise control is operating, speed control by the cruise control system will be canceled automatically. However, the set speed is kept in memory. |
| Coast Control | While the -SET switch on the steering pad switch assembly is pushed continuously, the vehicle speed and the set vehicle speed change as follows:
·
The vehicle will decelerate. ·
The set vehicle speed changes to the speed at which the -SET switch is released. |
| Tap Down Control | When the -SET switch on the steering pad switch assembly is pushed momentarily (approximately 0.6 seconds or less), the vehicle speed and the set vehicle speed change as follows:
·
The vehicle will decelerate in increments of approximately 1 km/h or 1 mph each time the switch is moved. ·
However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will change to the speed at which the vehicle is being driven when the switch is pushed. |
| Accelerator Control | While the +RES switch on the steering pad switch assembly is pushed continuously, the vehicle speed and the set vehicle speed change as follows:
·
The vehicle accelerates constantly. ·
The set vehicle speed changes to the speed at which the +RES switch is released. |
| Tap Up Control | When the +RES switch on the steering pad switch assembly is pushed momentarily (approximately 0.6 seconds or less), the vehicle speed and the set vehicle speed change as follows:
·
The vehicle will accelerate in increments of approximately 1 km/h or 1 mph each time the switch is moved. ·
However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will not change. |
| Resume Control | When the vehicle speed is above the low speed limit, the cruise control system resumes operation (when the +RES switch on the steering pad switch assembly is pushed) to reach the vehicle speed that was set at the time the driver canceled cruise control. Even if the vehicle speed dropped below the low speed limit, the set speed can be resumed after the vehicle speed increases above the low speed limit. Also, if the vehicle speed memory is deleted, the return control cannot be performed. |
| Shift Down Control | When the vehicle is traveling uphill using cruise control, automatic transmission control may cause the transmission to shift down. During shift-down control, when the end of uphill travel is determined based on the throttle valve angle, the transmission will shift up after a certain period of time. When the transmission shifts down during accelerator control or resume control, the transmission will shift up after accelerator control or resume control ends. |
| Manual Cancel Control | If any of the following signals are sent to the ECM, cruise control speed control operation is canceled accordingly.
·
Stop light switch on signal (The brake pedal is depressed). ·
Shift lever is moved from D or S to any other position. ·
When 1st, 2nd or 3rd range is selected in D position by shift paddle switch (Transmission shift switch assembly).* ·
Cruise control switch (ON-OFF switch) off signal. ·
CANCEL switch on signal (CANCEL switch on the steering pad switch assembly is pushed). |
| Automatic Cancel Control | If the following condition occurs during cruise control speed control operation, the speed that is set in memory is cleared and cruise control speed control operation is canceled.
·
Stop light switch open or short circuit. Furthermore, the master warning light illuminates, the cruise control indicator turns off, and a message indicating a malfunction will be displayed on the multi-information display until the cruise control system is turned off using the cruise control switch on the steering pad switch assembly. The operation of the cruise control is disabled until the cruise control system is turned on again using the cruise control switch on the steering pad switch assembly. |
| If the following condition occurs during cruise control speed control operation, the speed that is set in memory is cleared and cruise control speed control operation is canceled.
·
Malfunction in the engine control system. Furthermore, speed control by the cruise control system is disabled until the cruise control system is turned on again using the cruise control switch on the steering pad switch assembly. |
|
| If any of the following conditions occur during cruise control speed control operation, the speed that is set in memory is cleared and cruise control speed control operation is canceled.
·
Stop light switch input signal is abnormality. ·
Cancel circuit malfunction. ·
Communication malfunction between the skid control ECU and ECM. ·
Brake control system malfunction. Furthermore, the master warning light illuminates, the cruise control indicator light turns off, and a message indicating a malfunction will be displayed on the multi-information display until the cruise control system is turned off using the cruise control switch on the steering pad switch assembly. The operation of the cruise control is disabled until the ignition switch is turned off. |
|
| If the following condition occurs while the cruise control system is controlling the vehicle speed, the speed that is stored in memory is cleared and speed control by the cruise control system is canceled.
·
Vehicle speed decreases by 16 km/h (10 mph) or more below the speed at which the cruise control is set. |
|
| If the following condition occurs while the cruise control system is controlling the vehicle speed, speed control by the cruise control system is canceled.
·
Vehicle speed decreases below the low speed limit (approximately 40 km/h [25 mph]). |
|
| Other Cancellation Items | ·
VSC is activated. ·
TRC is activated for a period of time. ·
When the VSC or TRC system is turned off by pressing the VSC OFF switch. ·
Ignition switch off. |
DIAGNOSIS
If a malfunction occurs in the cruise control system during cruise control operation, the ECM cancels the cruise control, illuminates the master warning light, sounds a buzzer in the combination meter assembly, and displays a warning message on the multi-information display to inform the driver of the malfunction. At this time, the ECM memorizes the malfunction in the form of a Diagnostic Trouble Codes (DTCs).
The DTCs can be read by connecting the Global TechStream (GTS) to the DLC3. For details, refer to the Repair Manual.