FUNCTION OF MAIN COMPONENTS
| Components | Function | |
|---|---|---|
|
*: Models with headup display |
||
| Combination Meter Assembly | Transmits a turn signal command to the forward recognition camera. | |
| Combination Meter Assembly | Lane Departure Alert Indicator | Illuminates or turns off in accordance with signals from the forward recognition camera. |
| Multi-information Display | Displays a warning message and white lines to inform or warn the driver of the system condition in accordance with signals from the forward recognition camera. | |
| Master Warning Light | Illuminates to warn the driver in accordance with signals from the forward recognition camera. | |
| Buzzer | Sounds to warn the driver in accordance with signals from the forward recognition camera. | |
| Forward Recognition Camera | ·
Captures a view of the road ahead of the vehicle and detects lane markers on the driving lane, and calculates the radius to the center of the lane, lane width, distance from markers and heading angle deviation. ·
Controls the lane departure alert system. ·
Transmits the indicator illumination request signal, multi-information display indication request signal, and buzzer sound request signal to the combination meter assembly. ·
Receives vehicle information and turn signal light operation signals and sends a steering force signal to the power steering ECU. |
|
| Camera Heater (Forward Recognition Hood) | Heats the sheet heater in accordance with the signals from the forward recognition camera. | |
| Millimeter Wave Radar Sensor Assembly | Radiates millimeter waves forward, uses the reflected waves to detect the presence of a vehicle traveling ahead and then transmits this information to the forward recognition camera. | |
| ECM | ·
Sends the accelerator pedal opening angle signal to the forward recognition camera. ·
Sends the shift position signal to the forward recognition camera. |
|
| Turn Signal Switch | Transmits a turn signal command to the combination meter assembly. | |
| Brake Actuator Assembly | Skid Control ECU | Sends a vehicle speed signal from the speed sensor to the forward recognition camera. |
| Steering Pad Switch Assembly | Lane Departure Alert Main Switch | Detects an on/off status of the system and transmits a signal to the forward recognition camera. |
| Meter Control Switch | Changes the customize settings of the lane departure alert function, LDA steering assist function and vehicle sway warning function. | |
| Airbag Sensor Assembly | Yawrate Sensor | Detects yaw rate and transmits a signal to the forward recognition camera. |
| Steering Sensor | Detects the angle and direction of steering and transmits signals to the forward recognition camera. | |
| Rack and Pinion Power Steering Gear Assembly | Power Steering ECU | ·
Controls the power steering motor assembly according to signals from the forward recognition camera. ·
Sends steering torque signals from the torque sensor to the forward recognition camera. ·
Detects steering operations performed by the driver and outputs the operations to the forward recognition camera. ·
Cancels steering assist when an abnormal torque request signal is received from the forward recognition camera. |
| Main Body ECU (Multiplex Network Body ECU) | Sends country specification information signals to the forward recognition camera. | |
| Speed Sensor | Detects the vehicle speed and transmits a signal via the skid control ECU to the forward recognition camera. | |
| Meter Mirror Sub-assembly* | The headup display receives signals from the combination meter assembly in order to display the system conditions. | |
| Central Gateway ECU (Network Gateway ECU) | Gateway function of CAN communication. | |
OPERATION CONDITION
Operating Conditions of Lane Departure Alert System (Lane Departure Alert Function)
| Operation | Condition |
|---|---|
| Operating | The lane departure alert system (lane departure alert function) is activated when all of the following conditions are met:
·
The lane departure alert main switch is on. (When the lane departure alert main switch is pressed to turn on the lane departure alert system, the lane departure alert indicator illuminates). ·
The vehicle speed is above approximately 50 km/h (32 mph). ·
Lane markers are detected. ·
lane departure alert system becomes activated when the turning signal is set to the opposite direction against the heading direction. ·
System malfunction is not detected. |
| Suspended | The lane departure alert system (lane departure alert function) is suspended when any one of the following conditions is met:
·
The vehicle speed is less than approximately 50 km/h (32 mph). ·
A turn signal command is detected. ·
No lane markers are detected. ·
Immediately after the lane departure alert is activated. ·
A malfunction is detected in the lane departure alert system. ·
The temperature of the forward recognition camera is abnormal. ·
The vehicle crosses halfway or further over a lane marker. |
| Canceled/Resume | The lane departure alert system (lane departure alert function) is stopped when any one of the following conditions is met:
·
The lane departure alert main switch is off. ·
The lane departure alert system is malfunctioning. ·
The ignition switch is turned off. The lane departure alert system (lane departure alert function) resumes when the following conditions are met: ·
The conditions to start operation listed above returns to are satisfied. ·
The lane departure alert system condition returns to normal. ·
The ignition switch is turned off and on again to ensure normal operation, after the lane departure alert system has been stopped by a system malfunction. |
Operating Conditions of Lane Departure Alert System (Steering Assist Function)
| Operation | Condition |
|---|---|
| Operating | The lane departure alert system (steering assist function) is activated when all of the following conditions are met:
·
The lane departure alert main switch is on. (When the lane departure alert main switch is pressed to turn on the lane departure alert system, the lane departure alert indicator illuminates). ·
The vehicle speed is above approximately 50 km/h (32 mph). ·
Lane markers are detected. ·
No turn signal command is detected. ·
System malfunction is not detected. ·
The steering assist ON is selected via operation on the steering pad switch assembly. ·
Deceleration at or above a constant speed is not detected. ·
Steering operations to change the direction of vehicle travel are not performed. ·
Systems related to vehicle safety, such as the VSC and pre-collision system, do not operate. ·
Acceleration via operation of the accelerator pedal is not detected. |
| Suspended | The lane departure alert system (steering assist function) is suspended when any one of the following conditions is met:
·
The vehicle speed is less than approximately 50 km/h (32 mph). ·
A turn signal command is detected. ·
No lane markers are detected. ·
Immediately after the lane departure warning is activated. ·
A malfunction is detected in the lane departure alert system. ·
The airbag sensor assembly (yawrate sensor) is malfunctioning. ·
The deceleration sensor or steering sensor is malfunctioning. ·
The vehicle crosses halfway or further over a lane marker. ·
Steering assist generated to change the direction of vehicle travel is detected. ·
Deceleration at or above a constant speed is detected. ·
Systems related to vehicle safety, such as the VSC and pre-collision system, operate. ·
Acceleration via operation of the accelerator pedal is detected. ·
The temperature of the forward recognition camera is abnormal. ·
No steering wheel operation detected. |
| Canceled/Resume | The lane departure alert system (steering assist function) is stopped when any one of the following conditions is met:
·
The lane departure alert main switch is off. ·
The lane departure alert system is malfunctioning. ·
The ignition switch is turned off. ·
The steering assist OFF is selected via operation of the steering pad switch assembly. The lane departure alert system (steering assist function) resumes when the following conditions are met: ·
The conditions to start operation listed above returns to are satisfied. ·
The lane departure alert system condition returns to normal. ·
The ignition switch is turned off and ON again to ensure normal operation, after the lane departure alert system has been stopped by a system malfunction. ·
The steering assist ON is selected via operation on the steering pad switch assembly. |
Operating Conditions of Lane Departure Alert System (Vehicle Sway Warning Function)
| Operation | Condition |
|---|---|
| Operating | The lane departure alert system (vehicle sway warning function) is activated when all of the following conditions are met:
·
The vehicle speed is above approximately 50 km/h (32 mph). ·
Lane markers are detected. ·
System malfunction is not detected. ·
The vehicle sway warning ON is selected via operation of the steering pad switch assembly. |
| Suspended | The lane departure alert system (vehicle sway warning function) is suspended when any one of the following conditions is met:
·
The vehicle speed is less than approximately 50 km/h (32 mph). ·
A turn signal command is detected. ·
No lane markers are detected. ·
Immediately after the lane departure warning is activated. |
| Canceled/Resume | The lane departure alert system (vehicle sway warning function) is stopped when any one of the following conditions is met:
·
The lane departure alert system is malfunctioning. ·
The ignition switch is turned off. ·
The vehicle sway warning OFF is selected via operation of the steering pad switch assembly. The lane departure alert system (vehicle sway warning function) resumes when the following conditions are met: ·
The conditions to start operation listed above are satisfied. ·
The lane departure alert system condition returns to normal. ·
The ignition switch is turned off and on again to ensure normal operation, after the lane departure alert system has been stopped by a system malfunction. ·
The vehicle sway warning ON is selected via operation of the steering pad switch assembly. |
SYSTEM CONTROL
Function Overview
Lane Departure Alert Function
If the system judges that the vehicle may deviate from the lane it is in, the system illuminates the indicator in the combination meter display and sounds a buzzer so that the driver can take action to avoid lane departure.
Steering Assist Function
If the system judges that the vehicle may deviate from the lane it is in, the system performs steering assist to help the driver correct the path of the vehicle. If the driver does not take appropriate action, the system sounds a buzzer.
Vehicle Sway Warning
The system detects drift of the vehicle within its lane, which is often the result of a driver who is tired, distracted or not looking ahead, based on the position of the vehicle within its lane and the steering inputs of the driver and alert the driver before a lane departure or collision occurs.
FUNCTION
Using the meter control switches of the steering pad switch assembly, the steering assist functions and the vehicle sway warning functions can be customized.
| *a | Meter Control Switch | *b | Lane Departure Alert Main Switch |
| *c | This illustration is an example. | - | - |
Customize Lane Departure Alert System Settings Functions
| Item (Select using the up/down button of the meter control switch) | Description | Setting (Change using the center button of the meter control switch) |
|---|---|---|
| Steering Assist | Select to turn steering wheel assistance on/off | ·
ON ·
OFF |
| Warning Sensitivity | Timing of lane departure alert | ·
Standard ·
High |
Customize Vehicle Sway Warning Functions
| Item (Select using the up/down button of the meter control switch) | Description | Setting (Change using the center button of the meter control switch) |
|---|---|---|
| Vehicle Sway Warning | Select to turn the sway warning function on/off | ·
ON ·
OFF |
| Vehicle Sway Detection Sensitivity | Timing of sway warning | ·
High ·
Standard ·
Low |
DIAGNOSIS
If a malfunction is detected in the lane departure alert system, the forward recognition camera cancels the lane departure alert system, illuminates the lane departure alert indicator in yellow, illuminates the master warning light, sounds the buzzer in the combination meter assembly and displays a message on the multi-information display to inform the driver of the malfunction.
At the same time, the malfunction is stored in memory as a Diagnostic Trouble Code (DTC). When the Global TechStream (GTS) is connected to the DLC3, the DTC can be read. For details, refer to the Repair Manual.