Home › Drivetrain › U760E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › 2017.09–2021.02
NM33A0E _52 Drivetrain _065979 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0328983 AUTOMATIC TRANSAXLE SYSTEM CO CONTROL F

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  CONTROL  AUTOMATIC TRANSMISSION CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function

*1: Models with shift paddle switch (transmission shift switch assembly)

*2: Models with drive mode select switch

*3: Models with dynamic radar cruise control system

No. 1 Clutch (C1) Connects the intermediate shaft and the Ravigneaux planetary rear sun gear.
No. 2 Clutch (C2) Connects the intermediate shaft and the Ravigneaux planetary ring gear.
No. 1 Brake (B1) Prevents the Ravigneaux planetary front sun gear and the underdrive planetary carrier from turning clockwise or counterclockwise.
No. 2 Brake (B2) Prevents the Ravigneaux planetary ring gear from turning clockwise or counterclockwise.
No. 3 Brake (B3) Prevents the underdrive planetary ring gear from turning clockwise or counterclockwise.
No. 1 1-way Clutch (F1) Prevents the Ravigneaux planetary ring gear from turning counterclockwise.
Planetary Gears Change the route through which driving force is transmitted in accordance with the operation of each clutch and brake in order to increase or reduce the input and output speed.
Shift Solenoid Valve SL1 Controls the No. 1 clutch (C1) pressure.
Shift Solenoid Valve SL2 Controls the No. 2 clutch (C2) pressure.
Shift Solenoid Valve SL3 Controls the No. 1 brake (B1) pressure.
Shift Solenoid Valve SL4 Controls the No. 3 brake (B3) pressure.
Shift Solenoid Valve SLU
·

Controls the lock-up clutch pressure.

·

Controls the No. 2 brake (B2) pressure.


Shift Solenoid Valve SLT Controls line pressure.
Shift Solenoid Valve SL
·

Switches the lock-up relay valve.

·

Switches the B2 apply control valve and the reverse sequence valve.


Transmission Revolution Sensor Output Speed Sensor NC Detects the speed of the counter gear.
Input Speed Sensor NT Detects the input speed of the transaxle.
ATF Temperature Sensor (Transmission Wire) Detects the ATF temperature.
Accelerator Pedal Sensor Assembly Detects the accelerator pedal opening angle.
Throttle Body with Motor Assembly Throttle Position Sensor Detects the opening angle of the throttle valve.
Mass Air Flow Meter Sub-assembly Air Flow Meter Detects the intake air volume and intake air temperature.
Intake Air Temperature Sensor
Crank Position Sensor Detects the engine speed.
Engine Coolant Temperature Sensor Detects the engine coolant temperature.
Park/Neutral Position Switch Assembly Detects the shift lever position.
Transmission Floor Shift Assembly Transmission Control Switch
·

Detects when the shift lever is in S.

·

Detects the shift-up and shift-down operations performed by the driver when the shift lever is in S.


Shift Paddle Switch (Transmission Shift Switch Assembly)*1 Detects the shift-up and shift-down operations performed by the driver.
Electric Parking Brake Switch Assembly Drive Mode Select Switch*2 Selects the drive mode (ECO, NORMAL, SPORT).
Steering Pad Switch Assembly Cruise Control Switch Turns the cruise control system on and off, and conducts various operations including vehicle speed setting, acceleration, deceleration and control cancellation.
Stop Light Switch Assembly Detects when the brake pedal is depressed.
ECM
·

Controls each shift solenoid valve in response to a signal from each sensor and switch.

·

Makes a diagnosis and memorizes the failed section when the ECM detects a malfunction.


Air Conditioning Amplifier Assembly Transmits various air conditioning state signals to the ECM.
Airbag Sensor Assembly
·

Detects the vehicle's longitudinal and lateral acceleration.

·

Detects the vehicle's yaw rate.


Millimeter Wave Radar Sensor Assembly*3 Sends the information about the operation conditions of the dynamic radar cruise control system to the ECM.
Combination Meter Assembly Malfunction Indicator Lamp (MIL) Illuminates to inform the driver when the ECM detects a malfunction.
Multi-information Display
·

Displays the shift lever position.

·

Displays the shift range.

·

Displays the drive mode.*2


Buzzer Sounds when the shift-down operation is rejected.


SYSTEM CONTROL


a.

The electronic control system of the U760E automatic transaxle uses the controls listed below.

Control Outline

*1: Models with shift paddle switch (transmission shift switch assembly)

*2: Models with drive mode select switch

Shift Timing Control The ECM sends current to the shift solenoid valves SL1, SL2, SL3, SL4, SL and/or SLU based on signals from various sensors, in order to shift the gears.
Clutch to Clutch Pressure Control Controls the pressure that is applied directly to the C1, C2 clutches and B1, B3 brakes by actuating the shift solenoid valves (SL1, SL2, SL3 and SL4) in accordance with ECM signals.
Line Pressure Control Actuates the shift solenoid valve SLT to control the line pressure in accordance with information from the ECM and the operating conditions of the transaxle.
Lock-up Timing Control The ECM sends current to the shift solenoid valves SL and SLU based on signals from various sensors to engage or disengage the lock-up clutch.
Flex Lock-up Clutch Control Controls the shift solenoid valve SLU, provides an intermediate mode between the on and off states of the lock-up clutch, and increases the operating range of the lock-up clutch to improve fuel economy.
Powertrain Cooperative Control Controls both shift control and engine output control in an integrated way, achieving excellent shift characteristics and drivability.
Deceleration Downshift Control To prevent engine speed from decreasing and thereby maintain fuel cut, the ECM performs downshifts before fuel cut ends.
Direct Downshift Control Direct downshift control is used. This makes it possible to skip unnecessary shifts, enabling the vehicle to downshift directly from 6th to 3rd or from 5th to 2nd, enhancing downshift response when the accelerator pedal is depressed quickly.
Artificial Intelligence Shift Control (AI-shift Control) Based on the signals from various sensors, the ECM determines the road conditions and the intention of the driver. Thus, an appropriate shift pattern is automatically determined, improving drivability.
Multi-mode Automatic Transmission
·

When the shift lever is moved to S, driving in a gear position selected using the shift lever or shift paddle switch (transmission shift switch assembly)*1 is enabled.

·

Operating the shift paddle switch (transmission shift switch assembly) "-" with the shift lever in D enables D (fixed range mode).*1

·

The ECM appropriately controls the automatic transaxle in accordance with the range selected while in D (fixed range mode).*1


Drive Mode Select*2 Drive mode (NORMAL, ECO, SPORT) switching is performed via drive mode select operation.
Fail-safe If a malfunction is detected in the sensors or solenoids, the ECM performs fail-safe control to prevent the vehicle drivability from being affected significantly.
Diagnosis When the ECM detects a malfunction, the ECM records the malfunction and memorizes the information that relates to the fault.


b.

Clutch to Clutch Pressure Control

i.

Clutch to clutch pressure control is used for shift control. As a result, shift control in 2nd gear or above is possible without using a one-way clutch, making the automatic transaxle lightweight and compact.


ii.

Based on the information about transmission input and output speed, engine torque and other items, the ECM controls each clutch and brake accordingly with the optimum fluid pressure and timing, in order to shift the gears. The ECM changes gears using fluid pressure circuits which enable the clutches and brakes (C1, C2, B1 and B3) to be controlled independently, and using high flow SL1, SL2, SL3 and SL4 shift solenoid valves which directly control the line pressure. As a result, highly responsive and excellent shift characteristics have been realized.

X116059E01
4.177,0.521 6.875,0.906 2.698,0.385 10 false Intake Mass Air Flow Meter Sub-assembly 4.177,1.219 6.427,1.656 2.25,0.438 10 false Engine Coolant Temperature Sensor 4.167,1.906 5.698,2.323 1.531,0.417 10 false Throttle Position Sensor 0.958,0.5 2.583,0.938 1.625,0.438 10 false ATF Temperature Sensor 1.063,1.208 2.531,1.573 1.469,0.365 10 false Input Speed Sensor NT 0.917,1.906 2.521,2.479 1.604,0.573 10 false Output Speed Sensor NC 3.167,1.229 3.656,1.677 0.49,0.448 10 false ECM



c.

Line Pressure Control

i.

The line pressure is controlled using the shift solenoid valve SLT.


ii.

Through the use of the shift solenoid valve SLT, the line pressure is appropriately controlled in accordance with the engine torque information, as well as with the internal operating conditions of the torque converter and the transaxle.


iii.

Accordingly, the line pressure can be accurately controlled in accordance with the engine output, traveling condition, and the ATF temperature, thus realizing smooth shift characteristics and regulating the workload of the oil pump (reducing unnecessary parasitic losses).

X116060E01
0.344,4.24 0.958,4.438 0.615,0.198 10 false Pump 0.625,0.385 1.688,0.781 1.063,0.396 10 false Line Pressure 2.021,0.854 3.271,1.271 1.25,0.417 10 false Primary Regulator 2.969,1.365 4.708,1.771 1.74,0.406 10 false Solenoid Valve Drive Signal 3.5,3.771 4.417,4.365 0.917,0.594 10 false Shift Solenoid Valve SLT 1.958,4.146 2.552,4.531 0.594,0.385 10 false Fluid Pressure 2.802,5.104 3.875,5.302 1.073,0.198 10 false Current 5.5,0.771 6.948,1.146 1.448,0.375 10 false Input Speed Sensor NT 5.521,1.375 6.76,1.76 1.24,0.385 10 false ATF Temperature 5.542,2 6.448,2.354 0.906,0.354 10 false Shift Position 5.542,2.615 6.458,2.948 0.917,0.333 10 false Gear Position 5.531,3.229 6.625,3.563 1.094,0.333 10 false Intake Air Mass 5.469,5.115 6.844,5.51 1.375,0.396 10 false Throttle Valve Opening Angle 5.531,3.844 6.573,4.146 1.042,0.302 10 false Engine Speed 5.375,4.49 7.115,4.885 1.74,0.396 10 false Engine Coolant Temperature 4.896,2.781 5.354,2.979 0.458,0.198 10 false ECM



d.

Lock-up Timing Control

i.

The ECM uses lock-up timing control in order to improve the fuel economy in 2nd gear or higher when the shift lever is in D, or when the S6, S5 or S4 range has been selected.

Lock-up Operating Range in Each Gear
X138305E01
2.625,1.896 2.625,0.719 2.625,0.719 2.802,0.719 true 2.75,1.896 2.75,1.031 2.75,1.031 2.927,1.031 true 2.927,1.917 2.927,1.344 2.927,1.344 3.104,1.344 true 3.25,1.917 3.25,1.563 3.25,1.563 3.427,1.563 true 2.792,2.188 3.823,2.573 1.031,0.385 10 false Vehicle Speed 4.927,2.188 5.385,2.542 0.458,0.354 10 false High 1.24,1.042 2.292,1.448 1.052,0.406 10 false Throttle Opening Angle 1.896,0.552 2.281,0.927 0.385,0.375 10 false Large 4.51,1.792 4.969,2.146 0.458,0.354 10 false 6th 3.479,1.49 3.938,1.844 0.458,0.354 10 false 5th 3.156,1.25 3.615,1.604 0.458,0.354 10 false 4th 2.969,0.938 3.427,1.292 0.458,0.354 10 false 3rd 2.854,0.635 3.313,0.99 0.458,0.354 10 false 2nd

Lock-up Operation
Gear Shift Lever Position or Range
D or S6 S5 S4

○: Operates

X: Does not operate

-: Not applicable

1st X X X
2nd ○ ○ ○
3rd ○ ○ ○
4th ○ ○ ○
5th ○ ○ -
6th ○ - -



e.

Flex Lock-up Clutch Control

i.

During acceleration, the partial control of the power transmission between the lock-up clutch and torque converter greatly boosts the transmission efficiency in accordance with the driving conditions, improving the fuel economy.


ii.

Even when the vehicle is decelerating (the accelerator pedal is released), flex lock-up clutch control operates. Therefore, the fuel-cut area of the engine has been expanded and fuel-economy has been improved.


iii.

By allowing flex lock-up clutch control to continue operating during gearshifts, smooth torque transmission has been obtained. As a result, fuel economy and drivability have been improved.


iv.

For flex lock-up control, H infinity (H∞) control theory is used to achieve a high level of system stability and response to various characteristic changes.

X116061E01
1.885,1.792 1.885,1.531 1.885,1.531 1.719,0.938 true 4.677,3.781 4.281,3.781 true 1.146,0.323 0.917,0.323 0.917,0.323 0.917,1.094 true 2.646,3.219 2.646,2.969 2.646,2.969 2.375,2.969 true 2.125,3.677 2.031,4.188 2.031,4.188 1.875,4.188 true 3.844,4.563 3.844,5.479 3.844,5.479 3.656,5.479 true 4.823,5.188 4.646,5.188 4.646,5.188 4.146,4.563 true 5.031,4.802 4.854,4.802 4.854,4.802 4.479,4.344 true 3.677,0.854 4.135,1.052 0.458,0.198 10 false ECM 4.99,1.583 5.479,1.938 0.49,0.354 10 false Current 6.354,1.615 6.917,2.271 0.563,0.656 10 false Linear Solenoid Signal 5.979,2.292 6.333,2.563 0.354,0.271 10 false Time 4.75,3.708 5.635,4.208 0.885,0.5 10 false Speed Sensor NT 5.104,4.729 6.698,5.135 1.594,0.406 10 false ATF Temperature Sensor 4.885,5.094 6.448,5.458 1.563,0.365 10 false Shift Solenoid Valve SLU 2.271,5.385 3.646,5.74 1.375,0.354 10 false Lock-up Control Valve 0.094,4.104 1.865,4.563 1.771,0.458 10 false Engine Coolant Temperature Sensor 0.875,2.885 2.365,3.323 1.49,0.438 10 false Throttle Position Sensor 3.552,2.302 4,2.979 0.448,0.677 10 false Engine Speed Signal 1.156,1.833 2.688,2.406 1.531,0.573 10 false Speed Sensor NT Signal 0.781,1.417 1.74,1.823 0.958,0.406 10 false Vehicle Speed 0.219,0.729 0.677,1.115 0.458,0.385 10 false Engine Speed 1.219,0.24 2.573,0.698 1.354,0.458 10 false Engine Speed Signal


v.

The flex lock-up operating range has been expanded. Flex lock-up begins operating once the vehicle starts moving to lower engine speed and improve fuel economy.

Flex Lock-up Operating Range
X126506E03
4.938,2.021 5.135,1.281 5.135,1.281 5.625,1.281 true 3.219,2.365 3.219,1.021 3.219,1.021 3.396,1.021 true 1.594,0.823 2.094,1.156 0.5,0.333 10 false Large 0.885,1.625 1.948,2.531 1.063,0.906 10 false Throttle Opening Angle 1.885,2.708 2.854,3.094 0.969,0.385 10 false Vehicle Speed 3.229,2.875 4.688,3.479 1.458,0.604 10 false Flex Lock-up Operating Range (Deceleration) 5.333,2.719 5.813,3.083 0.479,0.365 10 false High 5.698,1.188 6.844,2.188 1.146,1 10 false Lock-up Operating Range 3.469,0.938 4.917,1.969 1.448,1.031 10 false Flex Lock-up Operating Range (Acceleration)

Flex Lock-up Operation
Gear Shift Lever Position or Range
D or S6 S5 S4 S3

○: Operates

X: Does not operate

-: Not applicable

*: Flex lock-up clutch control also operates when the vehicle decelerates.

1st X X X X
2nd ○ ○ ○ ○
3rd ○* ○* ○* ○
4th ○* ○* ○* -
5th ○* ○* - -
6th ○* - - -



f.

Powertrain Cooperative Control

i.

The engine output is appropriately controlled with the Electronic Throttle Control System-intelligent (ETCS-i) in real-time according to the transient force from the torque converter when the vehicle is launched. This achieves a high response and smooth acceleration, ensuring excellent launch performance.

X106856E11
4.073,1.698 5.365,2.385 1.292,0.688 10 false High Response and Smooth Acceleration 0.292,0.688 1.083,1.083 0.792,0.396 10 false Accelerator Pedal Angle 0.156,1.385 1.104,2.094 0.948,0.708 10 false Throttle Valve Opening Angle 0.333,3.125 1.094,3.5 0.76,0.375 10 false Drive Force 5.01,3.406 5.385,3.708 0.375,0.302 10 false Time 5.688,0.292 7.115,0.667 1.427,0.375 10 false : Without Control 5.688,0.677 6.615,1.052 0.927,0.375 10 false : With Control


ii.

The ECM determines the gear that is to be selected when the accelerator pedal is released (released completely) in accordance with the way the accelerator pedal is released (quickly or slowly) during deceleration. In this way, unnecessary upshifts are prevented during deceleration, matching the driver's intentions. In addition, unintended downshifts are prevented when accelerating the vehicle again, achieving smooth acceleration.

X100034E07
1.427,1.958 1.427,1.719 1.427,1.719 1.531,1.719 false 1.927,1.833 1.927,1.563 1.927,1.563 2.063,1.563 false 2.417,1.729 2.417,1.396 2.417,1.396 2.542,1.396 false 2.802,1.594 2.802,1.229 2.802,1.229 2.938,1.229 false 0.021,0.604 1.365,0.938 1.344,0.333 10 Speed of Accelerator Pedal Operation 0.823,1.604 1.271,1.979 0.448,0.375 10 Gear 0.542,2.24 1.427,2.615 0.885,0.375 10 Drive Force 1.583,1.604 1.854,1.938 0.271,0.333 10 3rd 2.094,1.469 2.365,1.802 0.271,0.333 10 4th 2.563,1.302 2.833,1.635 0.271,0.333 10 5th 2.99,1.146 3.26,1.479 0.271,0.333 10 6th 4.531,0.125 6.906,0.5 2.375,0.375 10 : Accelerator Pedal Operation (Slow) 4.531,0.479 6.906,0.854 2.375,0.375 10 : Accelerator Pedal Operation (Quick) 5.26,3.323 5.615,3.698 0.354,0.375 10 Time 4.177,1.979 5.729,2.635 1.552,0.656 10 Drive force change according to driver input.


iii.

Through cooperative control with the Electronic Throttle Control System-intelligent (ETCS-i) and Electronic Spark Advance (ESA), and electronic control of the engagement and release speed of the clutch and brake hydraulic pressures, quick response and shift shock reduction have been achieved.

X116062E01
0.927,0.5 2.177,1 1.25,0.5 10 false Driver's desired drive force 3.76,1.688 4.219,1.885 0.458,0.198 10 false ECM 0.198,2.031 1.323,2.563 1.125,0.531 10 false Accelerator Pedal Operation 1.656,2.146 2.604,2.542 0.948,0.396 10 false ETCS-i Control 1.781,2.708 2.552,3.063 0.771,0.354 10 false ESA Control 3.135,2.448 4.917,3.354 1.781,0.906 10 false Clutch engagement hydraulic pressure and timing 5.604,3.427 6.927,4.104 1.323,0.677 10 false Shift Solenoid Valve (SL1, SL2, SL3, SL4) 5.365,2.25 6.594,2.906 1.229,0.656 10 false Shift Solenoid Valve Control Signal 1.292,4.813 2.167,5.198 0.875,0.385 10 false Engine output 4.625,4.5 5.885,5.063 1.26,0.563 10 false Driver's desired drive force is achieved



g.

Coast Downshift Control

i.

The ECM performs downshift control to help prevent the engine speed from decreasing, thus keeping fuel cut control operating for as long as possible. In this way, fuel economy is improved.


ii.

For this control, when the vehicle is in 6th gear and starts decelerating, the transaxle downshifts from 6th to 5th, 5th to 4th, and 4th to 3rd before fuel cut control ends so that fuel cut continues operating. (The operation of 4th to 3rd downshift control is only available when the air conditioning system is off.)

X104227E11
3.146,3.49 3.146,3.594 3.146,3.594 2.906,3.594 true 3.396,3.5 3.396,3.823 3.396,3.823 3.219,3.823 true 2.469,3.073 2.469,2.635 2.469,2.635 2.396,2.635 true 2.833,3.271 2.833,2.354 2.833,2.354 2.688,2.354 true 3.208,1.198 3.031,0.646 3.031,0.646 2.802,0.646 true 3.146,3.313 3.146,2.354 3.146,2.354 3.292,2.354 true 3.448,3.344 3.448,2.604 3.448,2.604 3.958,2.604 true 3.656,3.51 3.656,3.813 3.656,3.813 3.865,3.813 true 4.698,0.677 6.26,0.896 1.563,0.219 10 false : With Downshift Control 4.688,1.042 6.448,1.26 1.76,0.219 10 false : Without Downshift Control 1.51,0.563 2.844,0.958 1.333,0.396 10 false Continuous Fuel Cut Operation 0.792,1.354 2.125,1.667 1.333,0.313 10 false Fuel Cut Control On 0.781,1.802 2.115,2.135 1.333,0.333 10 false Fuel Cut Control Off 2.271,2.271 2.75,2.49 0.479,0.219 10 false To 5th 2.167,2.552 2.479,2.771 0.313,0.219 10 false 6th 2.802,3.74 3.281,3.958 0.479,0.219 10 false To 4th 2.49,3.51 2.969,3.729 0.479,0.219 10 false To 5th 3.365,2.271 3.844,2.49 0.479,0.219 10 false To 4th 4.042,2.51 4.833,3.26 0.792,0.75 10 false To 3rd* 1.146,2.688 2.125,2.906 0.979,0.219 10 false Engine Speed 4.927,2.708 6.531,3.073 1.604,0.365 10 false Fuel Cut Control On 4.927,3.604 6.344,4 1.417,0.396 10 false Fuel Cut Control Off 4.708,4.063 5.135,4.281 0.427,0.219 10 false Time 3.969,3.719 5.396,3.979 1.427,0.26 10 false To 3rd* 0.156,4.271 1.99,4.615 1.833,0.344 10 false *: Only when A/C is off



h.

Direct Downshift Control

i.

For conventional downshift control, when shifting from 6th to 3rd or 5th to 2nd, downshifts use an intermediate gear in order to achieve smooth acceleration response. In addition to conventional control, direct downshift control is used for this vehicle. This control skips unnecessary shifts, enabling the vehicle to downshift directly from 6th to 3rd or from 5th to 2nd.


ii.

When the accelerator pedal is depressed quickly, direct downshift control enables direct downshifts with a quick shift response, skipping unnecessary shifts. Direct downshift control places the emphasis on reducing the time required to achieve the target gear. Conventional downshift control is used when the accelerator pedal is depressed slowly, providing smooth acceleration response. As a result, this logic achieves downshift responsiveness in accordance with the driver's intentions.

X104223E02
3.865,1.188 4.26,0.385 4.26,0.385 4.583,0.385 true 2.938,0.427 3.063,0.427 3.063,0.427 3.365,0.927 true 4.271,2.927 4.5,2.521 4.5,2.521 5.281,2.521 true 4.26,4.167 4.448,3.823 4.448,3.823 5.229,3.823 true 4.427,4.427 4.427,5.188 4.427,5.188 4.771,5.188 true 1.417,0.323 3,0.708 1.583,0.385 10 Direct Downshift Control 4.688,0.281 6.688,0.448 2,0.167 10 Conventional Downshift Control 5.354,2.427 6.854,2.771 1.5,0.344 10 Conventional Downshift Control 4.844,5.104 6.813,5.458 1.969,0.354 10 Conventional Downshift Control 5.208,0.844 5.479,1.021 0.271,0.177 10 2nd 5.208,1.094 5.479,1.271 0.271,0.177 10 3rd 5.219,1.344 5.49,1.542 0.271,0.198 10 4th 5.208,1.594 5.479,1.854 0.271,0.26 10 5th 2.427,3.333 3.51,3.667 1.083,0.333 10 Direct Downshift Control 5.302,3.729 6.854,3.875 1.552,0.146 10 Direct Downshift Control 0.667,1.125 1.99,1.49 1.323,0.365 10 Automatic Transaxle Input Speed 0.833,2.125 2.031,2.813 1.198,0.688 10 Accelerator Pedal Operation 0.885,2.927 1.885,3.302 1,0.375 10 Response Time 1.219,4.656 1.958,5.083 0.74,0.427 10 Drive Force



i.

Artificial Intelligence Shift Control (AI-shift Control)

i.

The automatic transmission gear is determined by the shift pattern, which uses the vehicle speed and throttle valve opening angle.


ii.

Additionally, AI-shift control enables the ECM to estimate the road conditions and the driver's intention in order to automatically control the shift pattern in the manner. As a result, a comfortable ride has been achieved.


iii.

AI-shift control includes road condition support control and driver's intention support control.


iv.

AI-shift control determines transaxle control based on input signals and automatically changes the shift pattern.

X100041E04
0.573,0.229 1.396,0.427 0.823,0.198 10 false Input Signals 0.542,0.865 1.458,1.063 0.917,0.198 10 false Sensor Signal 0.375,1.208 1.479,1.594 1.104,0.385 10 false - Throttle Opening Angle 0.375,1.865 1.375,2.042 1,0.177 10 false - Vehicle Speed 0.375,2.25 1.375,2.406 1,0.156 10 false - Engine Speed 0.375,2.646 1.375,2.823 1,0.177 10 false - Brake Signal 0.396,3.698 1.625,3.865 1.229,0.167 10 false Calculated by ECM 0.354,4.042 1.656,4.208 1.302,0.167 10 false Vehicle Acceleration 2.302,0.688 3.26,0.885 0.958,0.198 10 false AI-shift Control 2.563,1.042 3.583,1.24 1.021,0.198 10 false Road Condition 2.74,1.406 4.188,1.563 1.448,0.156 10 false Uphill/Downhill Driving 3.042,1.792 4.417,1.979 1.375,0.188 10 false Estimating the Grade 2.333,2.042 2.719,2.229 0.385,0.188 10 false Small 3.563,2.354 3.948,2.542 0.385,0.188 10 false Large 2.771,2.688 4.219,2.854 1.448,0.167 10 false Intended Acceleration 2.771,3.042 4.135,3.208 1.365,0.167 10 false Actual Acceleration 2.573,3.792 3.667,3.979 1.094,0.188 10 false Driver's Intention 2.354,4.208 3.552,4.594 1.198,0.385 10 false - Accelerator Pedal Operation 2.354,4.76 3.542,4.938 1.188,0.177 10 false - Vehicle Condition 3.885,4.375 4.906,4.771 1.021,0.396 10 false Estimating the Driver's Intention 5.813,0.302 7,0.698 1.188,0.396 10 false Basic Shift Pattern Control 5.813,2.313 6.792,2.667 0.979,0.354 10 false Road Condition Support Control 5.813,4.563 6.823,4.885 1.01,0.323 10 false Driver's Intention Support Control


v.

Under road condition support control, the ECM determines the throttle opening angle and the vehicle speed in addition to whether the vehicle is being driven uphill or downhill. To achieve the drive force required while driving uphill, this control prevents unnecessary upshifts. To achieve engine braking while driving downhill, this control automatically performs downshifts.

X106613E03
0.74,3.271 1.01,3.469 0.271,0.198 10 false 6th 0.75,4.042 1.063,4.281 0.313,0.24 10 false 6th 1.427,3.271 1.698,3.458 0.271,0.188 10 false 4th 1.625,4.042 1.917,4.24 0.292,0.198 10 false 4th 1.844,3.271 2.104,3.458 0.26,0.188 10 false 5th 2.51,3.271 2.74,3.49 0.229,0.219 10 false 5th 2.167,3.271 2.479,3.458 0.313,0.188 10 false 3rd 2.167,4.042 2.448,4.24 0.281,0.198 10 false 3rd 2.906,3.271 3.208,3.5 0.302,0.229 10 false 4th 4.354,4.042 4.677,4.24 0.323,0.198 10 false 3rd 3.281,4.042 3.594,4.25 0.313,0.208 10 false 4th 4.823,4.042 5.104,4.219 0.281,0.177 10 false 4th 5.302,4.042 5.552,4.229 0.25,0.188 10 false 5th 5.583,4.042 5.854,4.219 0.271,0.177 10 false 6th 5.573,3.271 5.823,3.448 0.25,0.177 10 false 6th 5.969,3.26 6.969,3.438 1,0.177 10 false Without Control 5.99,4.042 6.802,4.219 0.813,0.177 10 false With Control 3.229,3.281 4.292,3.719 1.063,0.438 10 false 5th (Brake Being Operated)


vi.

The ECM estimates the driver's intention based on the accelerator pedal operation and vehicle operating conditions to select a shift pattern that is well-suited to each driver, without the need to operate the shift pattern select switch used on conventional models.



j.

Multi-mode Automatic Transmission

i.

A multi-mode automatic transmission is designed to allow the driver to switch between gear ranges. By moving the shift lever to S and then moving the shift lever toward "+" (forward) or "-" (backward), the driver can select the desired shift range. Thus, the driver is able to shift gears with a manual-like feel.


ii.

This Multi-mode Automatic Transmission is designed to allow the driver to switch gear ranges; it is not for manually selecting single gears.


iii.

When the vehicle is being driven at a speed that is higher than the maximum safe speed for a downshift, any attempt to shift to a lower range by operating the shift lever will not be performed. This is done in order to protect the automatic transaxle. In this case, the ECM sounds the buzzer in the combination meter assembly twice to alert the driver.

X136631E01
1.5,0.156 3.417,0.667 1.917,0.51 10 false Combination Meter Assembly 1.615,0.51 3.208,1.073 1.594,0.563 10 false Multi-information Display 1.646,0.896 3.073,1.552 1.427,0.656 10 false Shift Position and Shift Range Indicator 0.719,6.427 2.677,6.76 1.958,0.333 10 false : CAN Communication Line 1.417,1.906 3.365,2.552 1.948,0.646 10 false Central Gateway ECU (Network Gateway ECU) 2.156,3.292 2.698,3.594 0.542,0.302 10 false ECM 3.656,3.063 4.781,3.469 1.125,0.406 10 false Shift-up Signal 3.646,3.427 4.99,3.833 1.344,0.406 10 false Shift-down Signal 3.656,3.781 5.177,4.188 1.521,0.406 10 false S Mode Position Signal 5.375,3.427 6.698,4.125 1.323,0.698 10 false Transmission Control Switch 5.448,2.583 6.646,3.323 1.198,0.74 10 false Transmission Floor Shift Assembly 5.396,0.51 6.625,1.323 1.229,0.813 10 false Shift Paddle Switch (Transmission Shift Switch Assembly)* 3.313,4.156 4.563,4.896 1.25,0.74 10 false Shift Solenoid Valve Control Signal 2,4.125 2.927,4.917 0.927,0.792 10 false Fluid Pressure Control Signal 0.688,4.115 1.729,4.75 1.042,0.635 10 false Ignition Advance Signal 3.021,5.219 3.688,6.063 0.667,0.844 10 false Automatic Transaxle 1.396,5.25 1.938,5.583 0.542,0.333 10 false Engine 4,6.104 7.01,6.75 3.01,0.646 10 false *: Models with Shift Paddle Switch (Transmission Shift Switch Assembly)


iv.

On models with the shift paddle switch (transmission shift switch assembly), in addition to the shift lever, a shift paddle switch (transmission shift switch assembly) has been provided on the steering wheel, allowing shifting operation similar to that of a manual transmission.


v.

The driver can select S mode by moving the shift lever to S. At this time, the 4th or 5th shift range will be selected according to the vehicle speed (during AI-shift control, however, the 3rd shift range may be selected).


vi.

Under this control, the ECM performs shift control within the usable gear range that the driver selects. As with an ordinary automatic transaxle, it shifts to 1st gear when the vehicle is stopped.


vii.

The shift lever position and the shift range are indicated by the shift indicator in the combination meter assembly (the shift range is shown only when the shift lever is in S, and it is not shown when the shift lever is in P, R, N or D).


viii.

When the shift lever is in S, the S mode indicator light in the combination meter assembly illuminates. The shift indicator light indicates the shift range that the driver has selected.


ix.

Holding the shift lever toward "+" with the shift lever in S will change the shift range to the S6 range regardless of the current range (S1 to S5).


x.

In order to prevent excessive engine speed, a function is used that automatically selects a higher shift range before engine speed becomes excessive.


xi.

In order to protect the automatic transmission, a function is adopted that automatically selects a higher shift range when the fluid temperature is high.

Usable Gear Chart
Shift Range Shift Indicator Light Usable Gear
S6 6 1st to 6th
S5 5 1st to 5th
S4 4 1st to 4th
S3 3 1st to 3rd
S2 2 1st to 2nd
S1 1 1st


xii.

High Response Upshift Control

·

The high response upshift control achieves highly responsive upshift operation using clutch to clutch pressure control, which regulates each clutch and brake quickly and precisely, and by using the powertrain cooperative control, which optimally regulates engine torque during shifting.

·

The high response upshift control activates when the shift lever is in S.

·

Engine torque reduction via engine integrated control is precisely controlled to the optimal state according to the driving conditions from the fuel cut to normal control.

HINT:

During D-range paddle active control, high response upshift control is not performed.


Upshift from 2nd to 3rd Gear
X117314E04
2.521,1.125 3.75,1.438 1.229,0.313 10 false Upshift Operation 4.771,0.24 6.729,0.51 1.958,0.271 10 false : High Response Upshift Control 4.771,0.635 6.729,0.906 1.958,0.271 10 false : Conventional Upshift Control 0.75,1.771 1.979,2.083 1.229,0.313 10 false Engine Speed 0.479,2.854 2.438,3.125 1.958,0.271 10 false High Response Upshift Control 0.625,3.208 2.583,3.479 1.958,0.271 10 false Conventional Upshift Control 4.854,1.396 6.083,1.708 1.229,0.313 10 false 2nd 4.854,2.01 6.083,2.323 1.229,0.313 10 false 3rd 4.594,2.427 5.823,2.74 1.229,0.313 10 false Time 5.292,2.844 6.969,3.115 1.677,0.271 10 false : Gear Shift Initiation Time 5.292,3.229 6.969,3.5 1.677,0.271 10 false : Gear Shift Time



xiii.

Blipping Downshift Control

·

The blipping downshift control regulates each clutch and brake using the clutch to clutch pressure control, allowing them to be engaged smoothly and disengaged quickly. In addition, fuel injection volume is increased and engine speed is boosted by the powertrain cooperative control, thus ensuring proper engine brake force. In this way, a smooth and quick downshift is achieved.

·

The blipping downshift control activates by downshifting with the shift lever in D or S.

Downshift from 3rd to 2nd Gear
X117315E04
4.792,0.24 6.583,0.542 1.792,0.302 10 false : Blipping Downshift Control 4.792,0.625 6.865,0.948 2.073,0.323 10 false : Conventional Downshift Control 2.594,0.896 4.667,1.219 2.073,0.323 10 false Downshift Operation 0.792,1.625 2.865,1.948 2.073,0.323 10 false Engine Speed 0.833,2.594 2.906,2.917 2.073,0.323 10 false Blipping Downshift Control 0.521,2.938 2.594,3.26 2.073,0.323 10 false Conventional Downshift Control 5.24,2.615 6.875,2.875 1.635,0.26 10 false : Gear Shift Initiation Time 5.25,3.083 6.885,3.344 1.635,0.26 10 false : Gear Shift Time 4.396,2.438 5.156,2.76 0.76,0.323 10 false Time 4.396,1.385 5.156,1.708 0.76,0.323 10 false 2nd 4.375,1.958 5.135,2.281 0.76,0.323 10 false 3rd




k.

D-range Paddle Active Control (Models with Shift Paddle Switch (Transmission Shift Switch Assembly))

i.

When the shift lever is in D, D-range paddle active control operates according to shift paddle switch (transmission shift switch assembly) operation and the system enters shift range selection mode. Shift paddle switch (transmission shift switch assembly) is provided on the back of the steering wheel to allow engine brake force control and downshift operations for acceleration to be performed while gripping the steering wheel.


ii.

The initial range when D-range paddle active control starts is determined according to the last gear position before shift paddle switch (transmission shift switch assembly) operation.

Initial Range when Control Starts
Gear Position before Shift Paddle Switch (Transmission Shift Switch Assembly) Operation Initial Range after Shift Paddle Switch (Transmission Shift Switch Assembly) "-" (Downshift) Operation Initial Range after Shift Paddle Switch (Transmission Shift Switch Assembly) "+" (Upshift) Operation
1st D1 D1
2nd D1 D2
3rd D2 D3
4th D3 D4
5th D4 D5
6th D5 -


iii.

Normal driving automatically resumes (automatic shift control) in the following conditions:

Normal Driving (Automatic Shift Control) Recovery Conditions
Situation Condition
Vehicle Stop 1 second after the vehicle stops, normal driving (automatic shift control) resumes.
Shift Paddle Switch (Transmission Shift Switch Assembly) "+" (Upshift) Operation Operate and Hold for 1 Second or More When operated and hold for 1 second or more, normal driving (automatic shift control) resumes.
Upshift to D6 Range Normal driving (automatic shift control) resumes immediately after operation.
Continuous Accelerator Pedal Depression D1 In order to prevent continuous driving at high loads caused by forgetting to switch from D-range paddle active control to normal driving (automatic shift control), when the accelerator pedal is continuously depressed for 3 seconds or more, normal driving (automatic shift control) resumes.
D2
D3
D4
D5




FUNCTION


a.

Drive Mode Select (Models with Drive Mode Select Switch)

i.

The motive force characteristics for the accelerator opening angle can be changed through the selection of the drive mode according to driver preference.


ii.

The drive mode can be selected by operating the drive mode select switch.


iii.

The selected drive mode will be shown on the multi-information display in the combination meter assembly.

X138323C01
2.99,3.5 2.99,2.708 true 6.396,0.677 6.229,0.677 6.229,0.677 6,1.208 true 2.906,3.542 3.219,3.698 0.313,0.156 10 false *1 6.458,0.583 6.771,0.781 0.313,0.198 10 false *a 0.094,3.521 0.406,3.677 0.313,0.156 10 false *b
*1 Electric Parking Brake Switch Assembly - -
*a Drive Mode Select Switch *b This illustration is an example only.


Characteristics of Drive Mode
Drive Mode Characteristics
NORMAL Mode This drive mode provides optimum driveability.
ECO Mode The ECM optimizes fuel economy and driving performance by gradually generating the motive force in comparison to the accelerator pedal operation. At the same time, the ECM supports eco driving by optimizing air conditioning performance.
SPORT Mode The ECM controls motive force in the intermediate area of the accelerator pedal opening to a greater degree than that of NORMAL mode, improving acceleration performance. In addition, engine speed response performance has been improved in the high area of the accelerator pedal opening, thus producing a sporty drive.




FAIL-SAFE


a.

The fail-safe function minimizes the loss of operability when an abnormality occurs in a sensor or a shift solenoid valve.


b.

For details, refer to the Repair Manual.



DIAGNOSIS


a.

When the ECM detects a malfunction, the ECM records the malfunction and memorizes the information related to the fault. Furthermore, the ECM illuminates the Malfunction Indicator Lamp (MIL) in the combination meter assembly to inform the driver.


b.

The ECM will also store Diagnostic Trouble Codes (DTCs) of the malfunctions. The DTCs stored in the ECM are output to the Global TechStream (GTS) via the DLC3.


c.

For details, refer to the Repair Manual.