Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE CONTROL SYSTEM
NM33A0E _54 Brake _067417 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0329247 BRAKE CONTROL SYSTEM DE DETAILS F

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE CONTROL SYSTEM  DETAILS  BRAKE CONTROL  


OPERATION


a.

Engine Output Control during TRC or VSC Operation

i.

During the TRC or VSC operation, the skid control ECU outputs the engine output control signal to the ECM. Upon receiving this signal, the ECM inhibits the engine output.

X100710E01
4.625,0.208 6.802,0.5 2.177,0.292 10 (A): Start of engine output control 4.625,0.615 6.208,0.938 1.583,0.323 10 (B): Start of brake control 4.625,1.01 6.417,1.354 1.792,0.344 10 (C): Brake control completed 4.625,1.417 7,1.75 2.375,0.333 10 (D): Engine output control completed 0.271,1.604 2.01,2.042 1.74,0.438 10 Level of Strong Front Wheel Skid or Rear Wheel Skid 2.24,1.917 2.552,2.198 0.313,0.281 10 (A) 2.531,1.917 2.854,2.198 0.323,0.281 10 (B) 4.573,1.917 4.844,2.198 0.271,0.281 10 (C) 4.865,1.917 5.177,2.177 0.313,0.26 10 (D) 0.448,2.833 1.573,3.198 1.125,0.365 10 Vehicle Condition 0.625,4.333 1.573,4.688 0.948,0.354 10 Engine Torque 0.677,5.729 1.573,6.313 0.896,0.583 10 Brake Wheel Cylinder Fluid Pressure* 5.688,3.583 6.021,3.927 0.333,0.344 10 Time 5.688,5.167 6.021,5.51 0.333,0.344 10 Time 5.688,6.74 6.021,7.083 0.333,0.344 10 Time 0.125,7.344 5.323,7.719 5.198,0.375 10 *: The wheel cylinder that activates varies depending on the condition of the vehicle



b.

ABS with EBD

i.

Based on the signals received from the 4 speed sensors, the skid control ECU calculates each wheel speed and deceleration, and checks wheel slipping conditions. According to the slipping condition, the skid control ECU controls the pressure holding valve and pressure reduction valve in order to adjust the fluid pressure of each wheel cylinder in the following 3 modes: pressure reduction, pressure holding and pressure increase modes.

X110377C03
0.417,0.219 2.563,4.51 2.146,4.292 2.74,0.219 4.771,4.51 2.031,4.292 4.865,0.219 6.938,4.51 2.073,4.292 1.583,1.573 1.729,0.74 1.729,0.74 1.938,0.74 true 0.729,2.979 0.948,2.979 0.948,2.979 1.344,3.292 true 2.01,0.677 2.323,0.833 0.313,0.156 10 *1 0.563,2.927 0.875,3.083 0.313,0.156 10 *2 1.417,2.354 1.729,2.51 0.313,0.156 10 *3 1.427,4.031 1.74,4.188 0.313,0.156 10 *4 0.521,0.281 0.833,0.438 0.313,0.156 10 *a 2.854,0.292 3.167,0.448 0.313,0.156 10 *b 4.99,0.292 5.302,0.448 0.313,0.156 10 *c 2.115,4.25 2.427,4.406 0.313,0.156 10 *d 4.927,2.771 5.24,2.927 0.313,0.156 10 *e 3.625,2.354 3.938,2.552 0.313,0.198 10 *3 5.771,2.344 6.083,2.542 0.313,0.198 10 *3 3.646,4.031 3.958,4.229 0.313,0.198 10 *4 5.771,4.021 6.083,4.219 0.313,0.198 10 *4 6.51,4.198 6.823,4.354 0.313,0.156 10 *f
*1 Port A *2 Port B
*3 Pressure Holding Solenoid Valve *4 Pressure Reduction Solenoid Valve
*a Increase Mode *b Holding Mode
*c Reduction Mode *d to Wheel Cylinder
*e to Reservoir and Pump *f from Wheel Cylinder


Not Activated Normal Braking - -
Activated Increase Mode Holding Mode Reduction Mode
Pressure Holding Solenoid Valve (Port A) OFF (Open) ON (Close) ON (Close)
Pressure Reduction Solenoid Valve (Port B) OFF (Close) OFF (Close) ON (Open)
Wheel Cylinder Pressure Increased Held Reduced



c.

Brake Assist

i.

In the event of emergency braking, the skid control ECU determines the driver's intentions based on the speed of the pressure increase in the master cylinder detected by the master cylinder pressure sensor signal. If the skid control ECU judges the need for additional brake assist, pressure to supplement the amount provided by the master cylinder is generated by the pump in the brake actuator and directed to each wheel cylinder.

X136383E02
0.625,1.292 3.073,1.49 2.448,0.198 10 false Speed Sensors (4) 0.354,3.229 2.802,3.427 2.448,0.198 10 false Stop Light Switch Assembly 3.146,0.5 5.594,0.698 2.448,0.198 10 false Solenoid Relay 3.094,1.896 5.542,2.094 2.448,0.198 10 false Skid Control ECU 3.24,3.49 5.688,3.688 2.448,0.198 10 false Motor Relay 5,0.333 6.802,0.885 1.802,0.552 10 false Master Cylinder Cut Solenoid Valves (2) 5.219,1.135 6.625,1.708 1.406,0.573 10 false Reservoir Cut Solenoid Valves (2) 5.094,1.906 6.74,2.427 1.646,0.521 10 false Pressure Holding Solenoid Valves (4) 5.01,2.708 6.802,3.177 1.792,0.469 10 false Pressure Reduction Solenoid Valves (4) 5.427,3.49 6.344,3.74 0.917,0.25 10 false Pump Motor 5.115,3.969 6.677,4.479 1.563,0.51 10 false Master Cylinder Pressure Sensor 0.594,6.313 2.521,6.698 1.927,0.385 10 false : CAN Communication Line 3.052,5.552 4.167,6.042 1.115,0.49 10 false Network Gateway ECU 5.167,4.813 6.823,5.156 1.656,0.344 10 false Brake Actuator Assembly 5.031,5.354 6.885,5.646 1.854,0.292 10 false Combination Meter Assembly 5.292,5.833 6.719,6.104 1.427,0.271 10 false Brake Warning Light 5.344,6.229 6.771,6.5 1.427,0.271 10 false ABS Warning Light

X112343C01
3.26,5.229 3.438,5.375 3.438,5.375 3.438,6.063 true 3.979,5.24 3.823,5.375 3.823,5.375 3.823,6.063 true 3.375,7.115 3.375,6.615 true 3.896,7.094 3.896,6.594 true 0.5,2.729 1.323,2.729 true 2.167,2.75 2.646,2.75 true 4.604,2.74 5.083,2.74 true 5.938,2.75 6.573,2.75 true 0.51,4.219 1.573,4.219 true 2.104,4.75 2.104,4.229 2.104,4.229 2.51,4.229 true 5.198,4.771 5.198,4.219 5.198,4.219 4.729,4.219 true 5.656,4.229 6.625,4.229 true 0.521,5.417 1.583,5.417 true 2.156,6.385 2.156,5.438 2.156,5.438 2.5,5.438 true 5.094,6.375 5.094,5.417 5.094,5.417 4.719,5.417 true 5.656,5.417 6.625,5.417 true 3.542,0.521 3.854,0.677 0.313,0.156 10 *1 0.292,2.646 0.604,2.958 0.313,0.313 10 (A) 5.552,1.76 5.865,1.917 0.313,0.156 10 *3 3.375,6.083 3.688,6.24 0.313,0.156 10 *4 3.313,7.146 3.625,7.302 0.313,0.156 10 *5 1.49,7.385 1.802,7.542 0.313,0.156 10 *6 2.531,7.375 2.844,7.531 0.313,0.156 10 *7 4.615,7.385 4.927,7.542 0.313,0.156 10 *8 5.698,7.365 6.01,7.521 0.313,0.156 10 *9 3.771,6.073 4.083,6.229 0.313,0.156 10 *4 3.844,7.125 4.156,7.281 0.313,0.156 10 *5 0.698,1.5 1.01,1.656 0.313,0.156 10 *2 1.958,2.667 2.271,2.979 0.313,0.313 10 (B) 5.115,2.667 5.427,2.979 0.313,0.313 10 (C) 6.625,2.667 6.938,2.979 0.313,0.313 10 (D) 1.229,3.323 1.542,3.635 0.313,0.313 10 (1) 2.531,3.323 2.844,3.635 0.313,0.313 10 (2) 4.49,3.344 4.802,3.656 0.313,0.313 10 (3) 5.813,3.323 6.125,3.635 0.313,0.313 10 (4) 0.313,4.135 0.625,4.448 0.313,0.313 10 (E) 2.042,4.781 2.354,5.094 0.313,0.313 10 (F) 5.115,4.792 5.427,5.104 0.313,0.313 10 (G) 1.51,4.823 1.823,5.135 0.313,0.313 10 (5) 2.438,4.813 2.75,5.125 0.313,0.313 10 (6) 4.604,4.823 4.917,5.135 0.313,0.313 10 (7) 5.542,4.813 5.854,5.125 0.313,0.313 10 (8) 1.49,6.01 1.802,6.323 0.313,0.313 10 (9) 2.427,5.99 2.74,6.302 0.313,0.313 10 (10) 4.594,6 4.906,6.313 0.313,0.313 10 (11) 5.49,6.01 5.802,6.323 0.313,0.313 10 (12) 6.656,4.146 6.969,4.458 0.313,0.313 10 (H) 0.365,5.323 0.677,5.635 0.313,0.313 10 (I) 2.104,6.406 2.417,6.719 0.313,0.313 10 (J) 5.021,6.396 5.333,6.708 0.313,0.313 10 (K) 6.667,5.323 6.979,5.635 0.313,0.313 10 (L)
*1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
*3 Master Cylinder Pressure Sensor *4 Pump
*5 Reservoir *6 Front Brake Caliper (Right Side)
*7 Rear Brake Caliper (Left Side) *8 Rear Brake Caliper (Right Side)
*9 Front Brake Caliper (Left Side) - -



ii.

Each valve operates as shown below:

Item Port Brake Assist Not Activated Brake Assist Activated

*: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions.

Master Cylinder Cut Solenoid Valve (1), (4) (A), (D) OFF (Open) ON*
Reservoir Cut Solenoid Valve (2), (3) (B), (C) OFF (Closed) ON (Open)
Front Brakes Pressure Holding Solenoid Valve (5), (8) (E), (H) OFF (Open) OFF (Open)
Pressure Reduction Solenoid Valve (9), (12) (I), (L) OFF (Closed) OFF (Closed)
Rear Brakes Pressure Holding Solenoid Valve (6), (7) (F), (G) OFF (Open) OFF (Open)
Pressure Reduction Solenoid Valve (10), (11) (J), (K) OFF (Closed) OFF (Closed)
Pump OFF ON



d.

TRC

i.

The fluid pressure generated by the pump is regulated by the master cylinder cut solenoid valves to achieve the required pressure. Thus, the brakes for the drive wheels are controlled in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes, to control slippage of the drive wheels.


ii.

The diagram shows the hydraulic circuit in pressure increase mode when TRC is activated. The pressure holding solenoid valves and the pressure reduction solenoid valves are turned ON/OFF according to the ABS and EBD operation pattern.

X136384E04
0.708,1.635 3.156,1.833 2.448,0.198 10 false Speed Sensors (4) 0.729,3.146 3.177,3.344 2.448,0.198 10 false VSC OFF Switch 3.198,0.552 5.646,0.75 2.448,0.198 10 false Solenoid Relay 3.146,2.094 5.594,2.292 2.448,0.198 10 false Skid Control ECU 3.323,3.625 5.771,3.823 2.448,0.198 10 false Motor Relay 5.083,0.438 6.885,0.854 1.802,0.417 10 false Master Cylinder Cut Solenoid Valves (2) 5.26,1.25 6.656,1.667 1.396,0.417 10 false Reservoir Cut Solenoid Valves (2) 5.156,2.052 6.802,2.469 1.646,0.417 10 false Pressure Holding Solenoid Valves (4) 5.073,2.865 6.865,3.302 1.792,0.438 10 false Pressure Reduction Solenoid Valves (4) 5.542,3.667 6.5,3.906 0.958,0.24 10 false Pump Motor 5.208,4.146 6.781,4.552 1.573,0.406 10 false Master Cylinder Pressure Sensor 5.188,5.01 6.979,5.344 1.792,0.333 10 false Brake Actuator Assembly 0.521,5.104 2.313,5.438 1.792,0.333 10 false Airbag Sensor Assembly 0.76,5.625 2.552,5.958 1.792,0.333 10 false Yawrate Sensor 0.677,6.094 2.469,6.427 1.792,0.333 10 false Acceleration Sensor 1.052,6.885 1.615,7.188 0.563,0.302 10 false ECM 3.115,5.979 4.229,6.385 1.115,0.406 10 false Network Gateway ECU 5.094,5.552 7.01,5.792 1.917,0.24 10 false Combination Meter Assembly 5.375,6.01 6.781,6.26 1.406,0.25 10 false Brake Warning Light 5.396,6.417 6.802,6.667 1.406,0.25 10 false ABS Warning Light 5.375,6.813 6.781,7.063 1.406,0.25 10 false Slip Indicator Light 5.25,7.208 6.854,7.479 1.604,0.271 10 false Multi-information Display 0.688,8.323 2.583,8.583 1.896,0.26 10 false : CAN Communication Line

X116976C03
0.625,2.75 1.323,2.75 true 2.177,2.74 2.646,2.74 true 4.594,2.74 5.063,2.74 true 5.917,2.74 6.615,2.74 true 0.677,4.219 1.583,4.219 true 2.063,4.615 2.063,4.219 2.063,4.219 2.51,4.219 true 5.177,4.635 5.177,4.229 5.177,4.229 4.708,4.229 true 5.635,4.229 6.542,4.229 true 0.688,5.406 1.594,5.406 true 2.146,6.365 2.146,5.406 2.146,5.406 2.521,5.406 true 5.094,6.396 5.094,5.427 5.094,5.427 4.719,5.427 true 5.646,5.417 6.552,5.417 true 3.438,6.063 3.438,5.375 3.438,5.375 3.26,5.24 true 3.802,6.073 3.802,5.385 3.802,5.385 3.979,5.24 true 3.365,6.604 3.365,7.063 true 3.875,6.604 3.875,7.063 true 3.521,0.531 3.833,0.688 0.313,0.156 10 false *1 0.646,1.531 0.958,1.688 0.313,0.156 10 false *2 5.531,1.792 5.844,1.948 0.313,0.156 10 false *3 3.354,6.104 3.667,6.26 0.313,0.156 10 false *4 3.302,7.104 3.615,7.26 0.313,0.156 10 false *5 1.51,7.271 1.823,7.427 0.313,0.156 10 false *6 2.448,7.271 2.76,7.427 0.313,0.156 10 false *7 4.604,7.25 4.917,7.406 0.313,0.156 10 false *8 5.583,7.229 5.896,7.385 0.313,0.156 10 false *9 0.427,2.688 0.74,2.844 0.313,0.156 10 false (A) 1.99,2.688 2.302,2.844 0.313,0.156 10 false (B) 5.094,2.677 5.406,2.833 0.313,0.156 10 false (C) 6.656,2.688 6.969,2.844 0.313,0.156 10 false (D) 1.26,3.344 1.573,3.5 0.313,0.156 10 false (1) 2.583,3.344 2.896,3.5 0.313,0.156 10 false (2) 4.531,3.333 4.844,3.49 0.313,0.156 10 false (3) 5.833,3.333 6.146,3.49 0.313,0.156 10 false (4) 0.458,4.167 0.771,4.323 0.313,0.156 10 false (E) 2,4.667 2.313,4.823 0.313,0.156 10 false (F) 5.115,4.688 5.427,4.844 0.313,0.156 10 false (G) 6.573,4.177 6.885,4.333 0.313,0.156 10 false (H) 0.49,5.344 0.802,5.5 0.313,0.156 10 false (I) 2.094,6.396 2.406,6.552 0.313,0.156 10 false (J) 5.031,6.427 5.344,6.583 0.313,0.156 10 false (K) 6.594,5.365 6.906,5.521 0.313,0.156 10 false (L) 1.542,4.823 1.854,4.979 0.313,0.156 10 false (5) 2.448,4.833 2.76,4.99 0.313,0.156 10 false (6) 4.646,4.833 4.958,4.99 0.313,0.156 10 false (7) 5.573,4.833 5.885,4.99 0.313,0.156 10 false (8) 1.542,6.052 1.854,6.208 0.313,0.156 10 false (9) 2.417,6.01 2.729,6.167 0.313,0.156 10 false (10) 4.604,6.01 4.917,6.167 0.313,0.156 10 false (11) 5.542,6.021 5.854,6.177 0.313,0.156 10 false (12) 3.719,6.104 4.031,6.26 0.313,0.156 10 false *4 3.813,7.104 4.125,7.26 0.313,0.156 10 false *5
*1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
*3 Master Cylinder Pressure Sensor *4 Pump
*5 Reservoir *6 Front Brake Caliper (Right Side)
*7 Rear Brake Caliper (Left Side) *8 Rear Brake Caliper (Right Side)
*9 Front Brake Caliper (Left Side) - -



iii.

Each valve operates as shown below:

Item Port TRC Not Activated TRC Activated
Increase Mode Holding Mode Reduction Mode

*: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions.

Master Cylinder Cut Solenoid Valve (1), (4) (A), (D) OFF (Open) ON* ON* ON*
Reservoir Cut Solenoid Valve (2), (3) (B), (C) OFF (Closed) ON (Open) ON (Open) ON (Open)
Front Brakes Pressure Holding Solenoid Valve (5), (8) (E), (H) OFF (Open) OFF (Open) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve (9), (12) (I), (L) OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
Brake Wheel Cylinder Pressure - - - Increased Held Reduced
Rear Brakes Pressure Holding Solenoid Valve (6), (7) (F), (G) OFF (Open) ON (Closed) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve (10), (11) (J), (K) OFF (Closed) ON (Open) ON (Open) ON (Open)
Brake Wheel Cylinder Pressure - - - - - -
Pump OFF ON ON ON



e.

VSC

i.

VSC, by way of solenoid valves, controls the fluid pressure generated by the pump and applies it to each wheel cylinder in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes. As a result, understeer and oversteer tendencies are controlled.

X136385E04
0.625,1.448 3.073,1.646 2.448,0.198 10 false Speed Sensors (4) 0.667,2.875 3.115,3.073 2.448,0.198 10 false VSC OFF Switch 3.125,0.417 4.375,0.677 1.25,0.26 10 false Solenoid Relay 3.063,2.01 4.313,2.271 1.25,0.26 10 false Skid Control ECU 3.219,3.479 4.469,3.74 1.25,0.26 10 false Motor Relay 5.031,0.292 6.833,0.76 1.802,0.469 10 false Master Cylinder Cut Solenoid Valves (2) 5.229,1.083 6.635,1.573 1.406,0.49 10 false Reservoir Cut Solenoid Valves (2) 5.104,1.885 6.74,2.375 1.635,0.49 10 false Pressure Holding Solenoid Valves (4) 5.031,2.698 6.813,3.146 1.781,0.448 10 false Pressure Reduction Solenoid Valves (4) 5.469,3.49 6.417,3.74 0.948,0.25 10 false Pump Motor 5.115,3.979 6.688,4.438 1.573,0.458 10 false Master Cylinder Pressure Sensor 5.167,4.854 6.823,5.177 1.656,0.323 10 false Brake Actuator Assembly 0.417,4.948 2.073,5.271 1.656,0.323 10 false Airbag Sensor Assembly 0.656,5.427 2.313,5.75 1.656,0.323 10 false Yawrate Sensor 0.563,5.938 2.219,6.26 1.656,0.323 10 false Acceleration Sensor 0.688,6.677 2.344,7 1.656,0.323 10 false Steering Sensor 1,7.417 2.656,7.74 1.656,0.323 10 false ECM 3.083,5.823 4.188,6.281 1.104,0.458 10 false Network Gateway ECU 5.042,5.427 6.969,5.75 1.927,0.323 10 false Combination Meter Assembly 5.313,5.938 6.958,6.281 1.646,0.344 10 false Brake Warning Light 5.323,6.323 6.969,6.667 1.646,0.344 10 false ABS Warning Light 5.354,6.74 7,7.083 1.646,0.344 10 false Slip Indicator Light 5.115,7.135 6.76,7.479 1.646,0.344 10 false VSC OFF Indicator Light 5.156,7.521 6.802,7.865 1.646,0.344 10 false Multi-information Display 0.635,8.354 2.479,8.615 1.844,0.26 10 false : CAN Communication Line


ii.

In understeer restraining control, the skid control ECU controls engine output and applies the brakes of the front and rear wheel on the inside of the turn. Also, depending on whether the brakes are applied and the vehicle condition, there are circumstances in which the brake of a specific wheel may not be applied even if it was targeted for braking. The diagram below shows the hydraulic circuit in pressure increase mode, as it restrains an understeer tendency while the vehicle is making a right turn. In other operating modes, the pressure holding valve and the pressure reduction valve are turned ON/OFF according to the ABS and EBD operation pattern.

VSC Operation (Understeer Restraining Control)
X112346C04
3.375,7.125 3.375,6.615 true 3.875,7.115 3.875,6.604 true 3.271,5.219 3.427,5.375 3.427,5.375 3.427,6.042 true 3.979,5.229 3.833,5.375 3.833,5.375 3.833,6.042 true 0.615,2.74 1.313,2.74 true 2.125,2.74 2.646,2.74 true 4.604,2.75 5.125,2.75 true 5.938,2.74 6.594,2.74 true 0.615,4.219 1.583,4.219 true 2.073,4.76 2.073,4.219 2.073,4.219 2.5,4.219 true 5.156,4.76 5.156,4.219 5.156,4.219 4.729,4.219 true 5.667,4.229 6.635,4.229 true 0.615,5.417 1.583,5.417 true 2.156,6.344 2.156,5.417 2.156,5.417 2.521,5.417 true 5.083,6.344 5.083,5.417 5.083,5.417 4.729,5.417 true 5.667,5.417 6.635,5.417 true 3.531,0.51 3.844,0.667 0.313,0.156 10 *1 0.688,1.438 1,1.594 0.313,0.156 10 *2 5.552,1.76 5.865,1.917 0.313,0.156 10 *3 3.375,6.073 3.688,6.229 0.313,0.156 10 *4 3.813,7.146 4.125,7.302 0.313,0.156 10 *5 1.458,7.313 1.771,7.469 0.313,0.156 10 *6 2.531,7.292 2.844,7.448 0.313,0.156 10 *7 4.573,7.323 4.885,7.479 0.313,0.156 10 *8 5.625,7.313 5.938,7.469 0.313,0.156 10 *9 3.323,7.167 3.635,7.323 0.313,0.156 10 *5 3.781,6.073 4.094,6.229 0.313,0.156 10 *4 0.396,2.667 0.698,2.99 0.302,0.323 10 (A) 1.917,2.667 2.219,2.99 0.302,0.323 10 (B) 5.167,2.677 5.469,3 0.302,0.323 10 (C) 6.635,2.667 6.938,2.99 0.302,0.323 10 (D) 0.406,4.146 0.708,4.469 0.302,0.323 10 (E) 2,4.792 2.302,5.115 0.302,0.323 10 (F) 5.094,4.792 5.396,5.115 0.302,0.323 10 (G) 6.667,4.156 6.969,4.479 0.302,0.323 10 (H) 0.458,5.333 0.76,5.656 0.302,0.323 10 (I) 2.083,6.375 2.385,6.698 0.302,0.323 10 (J) 5.031,6.375 5.333,6.698 0.302,0.323 10 (K) 6.677,5.344 6.979,5.667 0.302,0.323 10 (L) 1.271,3.323 1.583,3.573 0.313,0.25 10 (1) 2.583,3.323 2.896,3.573 0.313,0.25 10 (2) 4.51,3.323 4.823,3.573 0.313,0.25 10 (3) 5.833,3.313 6.146,3.563 0.313,0.25 10 (4) 1.531,4.823 1.844,5.073 0.313,0.25 10 (5) 2.448,4.823 2.76,5.073 0.313,0.25 10 (6) 4.646,4.813 4.958,5.063 0.313,0.25 10 (7) 5.573,4.813 5.885,5.063 0.313,0.25 10 (8) 1.531,6.01 1.844,6.26 0.313,0.25 10 (9) 2.448,6 2.76,6.25 0.313,0.25 10 (10) 4.615,6 4.927,6.25 0.313,0.25 10 (11) 5.552,6.021 5.865,6.271 0.313,0.25 10 (12)
*1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
*3 Master Cylinder Pressure Sensor *4 Pump
*5 Reservoir *6 Front Brake Caliper (Right Side)
*7 Rear Brake Caliper (Left Side) *8 Rear Brake Caliper (Right Side)
*9 Front Brake Caliper (Left Side) - -



iii.

Each valve operates as shown below:

Item Port VSC Not Activated VSC Activated
Increase Mode Holding Mode Reduction Mode

*: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions.

Master Cylinder Cut Solenoid Valve (1), (4) (A), (D) OFF (Open) ON* ON* ON*
Reservoir Cut Solenoid Valve (2), (3) (B), (C) OFF (Closed) ON (Open) ON (Open) ON (Open)
Front Brake Pressure Holding Solenoid Valve (5) (E) OFF (Open) OFF (Open) ON (Closed) ON (Closed)
(8) (H) OFF (Open) ON (Closed) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve (9) (I) OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
(12) (L) OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
Brake Wheel Cylinder Pressure Right - - Increased Held Reduced
Left - - Increased Held Reduced
Rear Brake Pressure Holding Solenoid Valve (6) (F) OFF (Open) ON (Closed) ON (Closed) ON (Closed)
(7) (G) OFF (Open) OFF (Open) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve (10) (J) OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
(11) (K) OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
Brake Wheel Cylinder Pressure Right - - Increased Held Reduced
Left - - - - -
Pump OFF ON ON ON


iv.

In oversteer restraining control, the skid control ECU applies the brakes of the front and rear wheels on the outside of the turn. Also, depending on whether the brakes are applied and the vehicle condition, the brake of a specific wheel may not be applied even if it was targeted for braking. The diagram below shows the hydraulic circuit in pressure increase mode, as it restrains an oversteer tendency while the vehicle is making a right turn. In other operating modes, the pressure holding valve and the pressure reduction valve are turned ON/OFF according to the ABS and EBD operation patterns.

VSC Operation (Oversteer Restraining Control)
X116977C02
0.688,2.74 1.333,2.74 true 2.125,2.75 2.656,2.75 true 4.594,2.75 5.125,2.75 true 5.906,2.75 6.552,2.75 true 0.74,4.219 1.594,4.219 true 2.073,4.719 2.073,4.229 2.073,4.229 2.51,4.229 true 5.198,4.729 5.198,4.229 5.198,4.229 4.708,4.229 true 5.635,4.208 6.448,4.208 true 0.74,5.417 1.594,5.417 true 2.146,6.333 2.146,5.396 2.146,5.396 2.521,5.396 true 5.646,5.417 6.5,5.417 true 5.094,6.354 5.094,5.417 5.094,5.417 4.708,5.417 true 3.438,6.052 3.438,5.396 3.438,5.396 3.26,5.229 true 3.813,6.052 3.813,5.396 3.813,5.396 4,5.229 true 3.365,6.615 3.365,7.167 true 3.865,6.604 3.865,7.156 true 3.542,0.5 3.854,0.656 0.313,0.156 10 false *1 0.667,1.49 0.979,1.646 0.313,0.156 10 false *2 5.552,1.771 5.865,1.927 0.313,0.156 10 false *3 3.385,6.104 3.698,6.26 0.313,0.156 10 false *4 3.281,7.188 3.594,7.344 0.313,0.156 10 false *5 1.479,7.26 1.792,7.417 0.313,0.156 10 false *6 2.542,7.25 2.854,7.406 0.313,0.156 10 false *7 4.594,7.24 4.906,7.396 0.313,0.156 10 false *8 5.656,7.24 5.969,7.396 0.313,0.156 10 false *9 0.5,2.677 0.813,2.833 0.313,0.156 10 false (A) 1.927,2.688 2.24,2.844 0.313,0.156 10 false (B) 5.167,2.688 5.479,2.844 0.313,0.156 10 false (C) 6.604,2.688 6.917,2.844 0.313,0.156 10 false (D) 1.292,3.333 1.552,3.5 0.26,0.167 10 false (1) 2.594,3.333 2.865,3.5 0.271,0.167 10 false (2) 4.51,3.323 4.771,3.49 0.26,0.167 10 false (3) 5.844,3.323 6.104,3.49 0.26,0.167 10 false (4) 1.521,4.833 1.781,5 0.26,0.167 10 false (5) 2.469,4.823 2.729,4.99 0.26,0.167 10 false (6) 4.646,4.823 4.906,4.99 0.26,0.167 10 false (7) 5.583,4.823 5.844,4.99 0.26,0.167 10 false (8) 0.552,4.146 0.865,4.302 0.313,0.156 10 false (E) 2.01,4.75 2.323,4.906 0.313,0.156 10 false (F) 5.125,4.76 5.438,4.917 0.313,0.156 10 false (G) 6.51,4.146 6.823,4.302 0.313,0.156 10 false (H) 2.104,6.365 2.417,6.521 0.313,0.156 10 false (J) 0.573,5.354 0.885,5.51 0.313,0.156 10 false (I) 5.031,6.354 5.344,6.51 0.313,0.156 10 false (K) 6.552,5.344 6.865,5.5 0.313,0.156 10 false (L) 1.521,6.021 1.781,6.188 0.26,0.167 10 false (9) 2.427,6.021 2.688,6.188 0.26,0.167 10 false (10) 4.604,6.021 4.865,6.188 0.26,0.167 10 false (11) 5.542,6.021 5.802,6.188 0.26,0.167 10 false (12) 3.719,6.104 4.031,6.26 0.313,0.156 10 false *4 3.792,7.188 4.104,7.344 0.313,0.156 10 false *5
*1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
*3 Master Cylinder Pressure Sensor *4 Pump
*5 Reservoir *6 Front Brake Caliper (Right Side)
*7 Rear Brake Caliper (Left Side) *8 Rear Brake Caliper (Right Side)
*9 Front Brake Caliper (Left Side) - -



v.

Each valve operates as shown below:

Item Port VSC Not Activated VSC Activated
Increase Mode Holding Mode Reduction Mode

*: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions.

Master Cylinder Cut Solenoid Valve (1), (4) (A), (D) OFF (Open) ON* ON* ON*
Reservoir Cut Solenoid Valve (2), (3) (B), (C) OFF (Closed) ON (Open) ON (Open) ON (Open)
Front Brake Pressure Holding Solenoid Valve (5) (E) OFF (Open) ON (Closed) ON (Closed) ON (Closed)
(8) (H) OFF (Open) OFF (Open) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve (9) (I) OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
(12) (L) OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
Brake Wheel Cylinder Pressure Right - - - - -
Left - - Increased Held Reduced
Rear Brake Pressure Holding Solenoid Valve (6) (F) OFF (Open) OFF (Open) ON (Closed) ON (Closed)
(7) (G) OFF (Open) ON (Closed) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve (10) (J) OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
(11) (K) OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
Brake Wheel Cylinder Pressure Right - - - - -
Left - - Increased Held Reduced
Pump OFF ON ON ON



f.

Hill-start Assist Operation

i.

When hill-start assist control is operating, the skid control ECU holds the brake fluid pressure.


ii.

Based on the information provided by various sensors, switches, and the ECM, the skid control ECU determines whether to activate hill-start assist control.

X137741E01
0.719,1.448 2.208,1.76 1.49,0.313 10 false Speed Sensors (4) 0.448,3.198 2.354,3.531 1.906,0.333 10 false Stop Light Switch Assembly 3.135,0.531 4.125,0.865 0.99,0.333 10 false Solenoid Relay 3.063,2.177 4.219,2.635 1.156,0.458 10 false Skid Control ECU 3.24,3.594 4.063,3.99 0.823,0.396 10 false Motor Relay 5.031,0.396 6.833,1 1.802,0.604 10 false Master Cylinder Cut Solenoid Valves (2) 5.229,1.198 6.677,1.729 1.448,0.531 10 false Reservoir Cut Solenoid Valves (2) 5.104,2 6.76,2.635 1.656,0.635 10 false Pressure Holding Solenoid Valves (4) 5.031,2.823 6.833,3.25 1.802,0.427 10 false Pressure Reduction Solenoid Valves (4) 5.531,3.615 6.698,3.896 1.167,0.281 10 false Pump Motor 5.125,4.104 6.74,4.573 1.615,0.469 10 false Master Cylinder Pressure Sensor 5.094,5 6.854,5.438 1.76,0.438 10 false Brake Actuator Assembly 0.458,5.24 2.115,5.646 1.656,0.406 10 false Airbag Sensor Assembly 0.729,5.76 1.917,6.063 1.188,0.302 10 false Yawrate Sensor 0.604,6.26 2.094,6.604 1.49,0.344 10 false Acceleration Sensor 3.073,6.427 4.208,6.938 1.135,0.51 10 false Network Gateway ECU 1.073,7.469 1.667,7.75 0.594,0.281 10 false ECM 0.604,8.5 2.813,8.823 2.208,0.323 10 false : CAN Communication Line

X112097C01
3.271,5.229 3.417,5.385 3.417,5.385 3.417,6.094 true 3.99,5.25 3.823,5.385 3.823,5.385 3.823,6.073 true 3.365,7.063 3.365,6.625 true 3.875,7.073 3.875,6.635 true 0.542,2.75 1.323,2.75 true 2.135,2.75 2.646,2.75 true 4.604,2.75 5.115,2.75 true 5.927,2.75 6.677,2.75 true 0.552,4.219 1.594,4.219 true 2.042,4.531 2.042,4.219 2.042,4.219 2.5,4.219 true 5.167,4.479 5.167,4.219 5.167,4.219 4.729,4.219 true 5.667,4.219 6.698,4.219 true 0.552,5.406 1.573,5.406 true 2.156,6.333 2.156,5.406 2.156,5.406 2.5,5.417 true 5.083,6.354 5.083,5.406 5.083,5.406 4.74,5.406 true 5.667,5.417 6.698,5.417 true 3.531,0.552 3.844,0.708 0.313,0.156 10 *1 0.677,1.458 0.99,1.615 0.313,0.156 10 *2 5.521,1.781 5.833,1.938 0.313,0.156 10 *3 3.365,6.104 3.677,6.26 0.313,0.156 10 *4 3.313,7.104 3.625,7.26 0.313,0.156 10 *5 1.385,7.271 1.698,7.427 0.313,0.156 10 *6 2.51,7.281 2.823,7.438 0.313,0.156 10 *7 4.604,7.26 4.917,7.417 0.313,0.156 10 *8 5.646,7.281 5.958,7.438 0.313,0.156 10 *9 3.76,6.104 4.073,6.26 0.313,0.156 10 *4 3.823,7.094 4.135,7.25 0.313,0.156 10 *5 1.917,2.656 2.375,2.854 0.458,0.198 10 (B) 0.333,2.667 0.792,2.865 0.458,0.198 10 (A) 5.167,2.677 5.625,2.875 0.458,0.198 10 (C) 6.719,2.667 7.031,2.906 0.313,0.24 10 (D) 1.26,3.344 1.719,3.542 0.458,0.198 10 (1) 2.573,3.333 3.031,3.531 0.458,0.198 10 (2) 4.51,3.333 4.969,3.531 0.458,0.198 10 (3) 5.823,3.354 6.281,3.552 0.458,0.198 10 (4) 1.531,4.802 1.99,5 0.458,0.198 10 (5) 2.448,4.813 2.906,5.01 0.458,0.198 10 (6) 4.635,4.823 5.094,5.021 0.458,0.198 10 (7) 5.563,4.823 6.021,5.021 0.458,0.198 10 (8) 1.542,6.01 2,6.208 0.458,0.198 10 (9) 2.396,6 2.854,6.198 0.458,0.198 10 (10) 4.604,6 5.063,6.198 0.458,0.198 10 (11) 5.531,6.01 5.99,6.208 0.458,0.198 10 (12) 0.344,4.125 0.802,4.323 0.458,0.198 10 (E) 1.969,4.573 2.427,4.771 0.458,0.198 10 (F) 5.083,4.51 5.542,4.708 0.458,0.198 10 (G) 6.74,4.125 7.052,4.365 0.313,0.24 10 (H) 0.396,5.313 0.854,5.51 0.458,0.198 10 (I) 2.094,6.354 2.552,6.552 0.458,0.198 10 (J) 5.01,6.385 5.469,6.583 0.458,0.198 10 (K) 6.74,5.323 7.052,5.563 0.313,0.24 10 (L)
*1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
*3 Master Cylinder Pressure Sensor *4 Pump
*5 Reservoir *6 Front Brake Caliper (Right Side)
*7 Rear Brake Caliper (Left Side) *8 Rear Brake Caliper (Right Side)
*9 Front Brake Caliper (Left Side) - -


Item Port Not Activated Hill-start Assist Control Activated
Holding Mode Reduction Mode

*: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions.

Master Cylinder Cut Solenoid Valve (1), (4) (A), (D) OFF (Open) ON* ON*
Reservoir Cut Solenoid Valve (2), (3) (B), (C) OFF (Closed) OFF (Closed) OFF (Closed)
Front Brakes Pressure Holding Solenoid Valve (5), (8) (E), (H) OFF (Open) OFF (Open) OFF (Open)
Pressure Reduction Solenoid Valve (9), (12) (I), (L) OFF (Closed) OFF (Closed) OFF (Closed)
Brake Wheel Cylinder Pressure - - Hold Reduce
Rear Brakes Pressure Holding Solenoid Valve (6), (7) (F), (G) OFF (Open) OFF (Open) OFF (Open)
Pressure Reduction Solenoid Valve (10), (11) (J), (K) OFF (Closed) OFF (Closed) OFF (Closed)
Brake Wheel Cylinder Pressure - - Hold Reduce
Pump OFF OFF OFF



g.

Brake Hold

i.

The operation of the solenoid valves under the brake hold is the same as the operation of the hill-start assist control.



h.

VSC and Cooperative Control with EPS

i.

The operation of the solenoid valves under the steering cooperative control is the same as the TRC or VSC operation.