Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › 2017.09–2017.12
NM33A0E _58 Vehicle Interior _067429 HEATING / AIR CONDITIONING _0329256 AIR CONDITIONING SYSTEM GE GENERAL F

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  GENERAL  GENERAL  


OUTLINE


a.

The automatic air conditioning system uses left and right independent temperature control andneural network control to enhance comfort.


b.

An inside-and-outside dual air layer type air conditioning unit is provided depending on the model.


c.

HFC-134a refrigerant is used.


d.

The automatic air conditioning system uses driver, front passenger and rear passenger* independent temperature control to enhance comfort.

*: Models with 3-zone control



SPECIFICATION


a.

Ventilation and Heater Core

*1: Models with dual air layer type air conditioning unit

*2: Models with single air layer type air conditioning unit

Heater Radiator Unit Sub-assembly Type Straight Flow Aluminum (SFA)-II
Size (W x H x L) mm (in.) 263.9 x 120 x 27
(10.4 x 4.7 x 1.1)
Blower with Fan Motor Sub-assembly*1 Motor Type DC Ferrite Brushless
Fan Type Semi Sirocco
Fan Size (Dia. x H) mm (in.) Upper Side: 122.0 x 55.0 (4.8 x 2.2)
Lower Side: 125.0 x 38.0 (4.9 x 1.5)
Blower with Fan Motor Sub-assembly*2 Motor Type DC Ferrite Brushless
Fan Type Semi Sirocco
Fan Size (Dia. x H) mm (in.) 137.0 x 70.0 (5.4 x 2.8)


b.

Air Conditioning

*1: Except models with 2GR-FKS engine

*2: Models with 2GR-FKS engine

Cooler Condenser Assembly Type Global Inner-fin Condenser (GIC)
Size (W x H x L) mm (in.) 700 x 453 x 11.5
(27.6 x 17.8 x 0.5)
Fin Pitch mm (in.) 3.0 (0.12)
Compressor with Pulley Assembly*1 Type 7SES17C
Pulley Plastic Damper Limiter (DL)
Compressor with Pulley Assembly*2 Type 7SAS17C
Pulley Steel with Magnet Clutch
Refrigerant Type HFC-134a
Evaporator Type Beneficial Refrigerant Stream (BRS) Evaporator
Size (W x H x L) mm (in.) 279.7 x 231.0 x 38.0 (11.0 x 9.1 x 1.5)
Fin Pitch mm (in.) 3.0 (0.12)



MAIN FEATURES


a.

The air conditioning system has the following features:

High Performance
·

Neural network control is used so passengers can finely control the air conditioning for maximum comfort.

·

A high efficiency type clean air filter, which has a pollen-and-odor removal effect, is used.

·

The blower control has 7 steps to allow precise control.

·

Using the following features of the compressor (continuously variable capacity compressor), high cooling performance and a quiet cabin have been achieved:

-

Oil Separator

-

Variable Suction Side Throttle

-

Solenoid Valve with Built-in Crank Chamber to Suction Passage (CS) Valve



Lightweight
·

An air conditioning harness assembly with a built-in communication/driver IC is used in a lightweight wire harness design to allow a reduced number of wires.

·

The use of this type of connector means that pulse pattern type servo motors can be used.


Others The following parts are used to ensure high cooling performance while realizing a compact and lightweight construction.
·

Semi-center Location Air Conditioning Unit

·

Beneficial Refrigerant Stream (BRS) Evaporator

·

Straight Flow Aluminum (SFA)-II Heater Radiator Sub-assembly

·

Global Inner-fin Condenser (GIC) Sub-cool Condenser