Home › Engine / Hybrid System › A25A-FKS (ENGINE CONTROL) › SFI SYSTEM
NM33A0E _51 Engine / Hybrid System _067502 A25A-FKS ENGINE CONTROL _0329602 SFI SYSTEM CO CONTROL F

A25A-FKS ENGINE CONTROL  SFI SYSTEM  CONTROL  DIRECT INJECTION 4-STROKE GASOLINE ENGINE SURERIOR VERSION SEQUENTIAL MULTIPORT FUEL INJECTION (D-4S SFI)  


FUNCTION


a.

A Direct injection 4-stroke gasoline engine Superior version Sequential multiport Fuel Injection (D-4S SFI) system which has both direct injection type and port injection type is used for the fuel injection system.


b.

The intake air mass is detected by the mass air flow meter sub-assembly to control the fuel injection volume.


c.

Based on signals from each sensor, the ECM controls the injection volume and timing of port fuel injector assembly and direct fuel injector assembly in accordance with the engine speed and engine load in order to optimize combustion conditions. Due to this, engine oil dilution reduction, low fuel consumption, and improved emissions as well as high engine output are achieved.


d.

In order to fully maximize the effectiveness of direct injection (cooling effect, jet stream use, air-fuel mixture form variance), a multi-fuel injection system in which the injectors are pulsed multiple times during each injection is used. A D-4S injection control system that maximizes the merits of the port injection and direct injection is used.


e.

Partial lift injection is used instead of full lift injection for direct injection while the engine is warmed up. By optimizing the fuel injection volume for partial lift injection, lower emissions have been achieved.

Fuel Injector System Activation Ranges
W136137E01
1.833,3.083 2.083,3.083 2.083,3.083 2.5,2.667 true 5.083,1.583 5.583,0.917 5.583,0.917 5.75,0.917 true 2.771,1.875 4.667,2.104 1.896,0.229 10 false Direct Injection + Port Injection 5.802,0.823 6.771,1.031 0.969,0.208 10 false Direct Injection 0.969,2.979 1.792,3.188 0.823,0.208 10 false Port Injection 0.51,1.906 1.573,2.135 1.063,0.229 10 false Engine Load (%) 3.042,3.198 4.313,3.448 1.271,0.25 10 false Engine Speed (rpm) 2.427,2.865 2.792,3.073 0.365,0.208 10 false 1000 3.49,2.865 3.854,3.073 0.365,0.208 10 false 2800 4.667,2.875 5.031,3.083 0.365,0.208 10 false 4800 1.771,1.49 1.969,1.667 0.198,0.177 10 false 70 1.771,1.677 1.969,1.854 0.198,0.177 10 false 60 1.781,2.302 1.979,2.479 0.198,0.177 10 false 25

Partial Lift Injection Area
W136138E01
1.167,1.031 2.104,1.427 0.938,0.396 10 false Injector Needle Position 3.354,2.042 4.24,2.229 0.885,0.188 10 false Injection Time 5.542,0.667 6.74,1.042 1.198,0.375 10 false Injector Needle Full Lift Position 0.865,2.49 1.99,2.698 1.125,0.208 10 false : Full Lift Injection 0.865,2.24 2.229,2.448 1.365,0.208 10 false : Partial Lift Injection 2.021,0.156 2.365,0.385 0.344,0.229 10 true (um) 5.438,1.875 5.865,2.125 0.427,0.25 10 true (usec)

W136205E01
3.635,4.188 4.094,4.385 0.458,0.198 10 false ECM 0.396,0.365 2.625,0.625 2.229,0.26 10 false Mass Air Flow Meter Sub-assembly 0.563,1.219 2.469,1.469 1.906,0.25 10 false Intake Air Temperature Sensor 0.823,1.844 2.281,2.104 1.458,0.26 10 false Crank Position Sensor 0.677,2.396 2.323,2.792 1.646,0.396 10 false Camshaft Position Sensor (Intake) 0.656,3.188 2.302,3.583 1.646,0.396 10 false Camshaft Position Sensor (Exhaust) 0.844,3.979 2.198,4.198 1.354,0.219 10 false Air Fuel Ratio Sensor 0.594,4.521 2.333,4.76 1.74,0.24 10 false No. 2 Air Fuel Ratio Sensor 0.354,5.083 2.625,5.344 2.271,0.26 10 false Accelerator Pedal Sensor Assembly 0.75,5.625 2.281,5.885 1.531,0.26 10 false Throttle Position Sensor 0.635,6.177 2.344,6.417 1.708,0.24 10 false Vacuum Sensor Assembly 0.406,6.729 2.656,6.969 2.25,0.24 10 false Engine Coolant Temperature Sensor 0.094,7.271 2.906,7.677 2.813,0.406 10 false Fuel Pressure Sensor (Fuel Delivery Pipe with Sensor Sub-assembly) (for Low Pressure) 0.25,8.073 2.781,8.323 2.531,0.25 10 false Fuel Pressure Sensor (for High Pressure) 4.906,2.552 6.646,2.781 1.74,0.229 10 false Port Fuel Injector Assembly 4.917,5.635 6.781,5.875 1.865,0.24 10 false Direct Fuel Injector Assembly


f.

Fuel Cut

i.

When the engine speed exceeds the specified value, fuel injection is stopped to prevent over-revving.

Engine Speed for Fuel-cut at High Revs
Engine speed (rpm) 6900 or more