Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › SFI SYSTEM
NM33A0E _51 Engine / Hybrid System _067496 2GR-FKS ENGINE CONTROL _0329779 SFI SYSTEM CO CONTROL F

2GR-FKS ENGINE CONTROL  SFI SYSTEM  CONTROL  DIRECT INJECTION 4-STROKE GASOLINE ENGINE SURERIOR VERSION SEQUENTIAL MULTIPORT FUEL INJECTION (D-4S SFI)  


FUNCTION


a.

The D-4S SFI system directly detects the intake air volume with a hot-wire type mass air flow meter sub-assembly.


b.

The D-4S system is a fuel injection system which combines direct injection injectors and port injection injectors.


c.

Based on signals from each sensor, the ECM controls the injection volume and timing of each type of fuel injector (direct and port injection types) in accordance with engine load and engine speed in order to optimize combustion conditions.


d.

To promote warm-up of the catalyst after a cold engine start, this system uses a stratified air fuel mixture. This creates an area near the spark plug that is richer than the rest of the air fuel mixture. This also allows a greater amount of ignition timing retard to be used, raising the exhaust gas temperature. The increased exhaust gas temperatures promote rapid warm-up of the catalysts, significantly reducing exhaust emissions.

Fuel Injector System Activation Ranges
W123296E05
5.094,1.521 5.156,1.083 5.156,1.083 5.469,1.083 true 2.375,2.052 2.688,0.385 2.688,0.385 3.115,0.385 true 0.438,1.813 1.51,2.01 1.073,0.198 10 false Engine Load 5.552,1.01 6.5,1.344 0.948,0.333 10 true Direct Injection 2.125,2.458 4.083,2.708 1.958,0.25 10 true Direct Injection or Port Injection 3.146,0.323 5.073,0.708 1.927,0.385 10 true Direct Injection + Port Injection 3.24,2.938 4.25,3.167 1.01,0.229 10 true Engine Speed


e.

Stratified Combustion: To achieve stratified combustion, immediately after a cold engine start, fuel is injected into the intake port from the fuel injector assembly (for port injection) during the exhaust stroke. Fuel is also injected from the fuel injector assembly (for direct injection) near the end of the compression stroke. This results in an air fuel mixture that is stratified, and the area near the spark plug is richer than the rest of the air fuel mixture. This allows a retarded ignition timing to be used, raising the exhaust gas temperature. The increased exhaust gas temperatures promote rapid warm up of the catalysts, and significantly improve exhaust emission performance.


f.

Homogeneous Combustion: To optimize combustion conditions, the ECM controls injection volume and timing of the fuel injector assemblies (for port injection) which inject fuel into the intake ports during the expansion, exhaust, and intake strokes. The ECM also controls the injection volume and timing of the fuel injector assemblies (for direct injection) which inject fuel during the first half of the intake stroke. The homogeneous air fuel mixture is created by either combined or individual use of the 2 different types of injectors. This allows utilization of the evaporation heat of the injected fuel to cool the compressed air, and it also allows an increase of charging efficiency and power output.

W130633E01
0.281,0.188 2.5,0.51 2.219,0.323 10 false Mass Air Flow Meter Sub-assembly 0.406,1.094 2.333,1.292 1.927,0.198 10 false Intake Air Temperature Sensor 0.615,1.792 2.052,2.01 1.438,0.219 10 false Crank Position Sensor 0.271,2.417 2.417,2.844 2.146,0.427 10 false Cam Position Sensor (No. 2 Crank Position Sensor) (Intake) 0.323,3.26 2.49,3.615 2.167,0.354 10 false Cam Position Sensor (No. 2 Crank Position Sensor) (Exhaust) 4.427,2.469 6.979,2.698 2.552,0.229 10 false Fuel Injector Assembly (for Port Injection) 3.406,3.885 3.729,4.083 0.323,0.198 10 false ECM 0.604,4.115 2.135,4.302 1.531,0.188 10 false Heated Oxygen Sensor 0.656,4.729 2.021,4.927 1.365,0.198 10 false Air Fuel Ratio Sensor 0.302,5.333 2.615,5.542 2.313,0.208 10 false Accelerator Pedal Sensor Assembly 4.396,5.542 7.083,5.729 2.688,0.188 10 false Fuel Injector Assembly (for Direct Injection) 0.552,5.948 2.083,6.167 1.531,0.219 10 false Throttle Position Sensor 0.292,6.573 2.552,6.771 2.26,0.198 10 false Engine Coolant Temperature Sensor 0.156,7.177 2.677,7.396 2.521,0.219 10 false Fuel Pressure Sensor (for Low Pressure) 0.146,7.802 2.719,8.052 2.573,0.25 10 false Fuel Pressure Sensor (for High Pressure)


g.

Fuel Cut

i.

When the engine speed exceeds the specified value, fuel injection is stopped to prevent over-revving.

Engine Speed for Fuel-cut at High Revs
Engine speed (rpm) 6900 or more