Home › Engine / Hybrid System › 2AR-FE (ENGINE CONTROL) › SFI SYSTEM › 2017.09–2021.02
NM33A0E _51 Engine / Hybrid System _067506 2AR-FE ENGINE CONTROL _0330023 SFI SYSTEM CO CONTROL F

2AR-FE ENGINE CONTROL  SFI SYSTEM  CONTROL  DRIVE START CONTROL SYSTEM  


FUNCTION


a.

When abnormal driver accelerator pedal and shift operations are detected, the system restricts the driving force and informs the driver.

W136209E05
3.427,3.031 3.885,3.229 0.458,0.198 10 false ECM 0.365,0.198 1.969,0.615 1.604,0.417 10 false Accelerator Pedal Sensor Assembly 0.51,1.094 1.865,1.552 1.354,0.458 10 false Park/Neutral Position Switch Assembly 0.24,2.031 2.219,2.479 1.979,0.448 10 false Central Gateway ECU (Network Gateway ECU) 0.667,2.927 1.729,3.146 1.063,0.219 10 false Steering Sensor 0.417,3.49 1.99,3.771 1.573,0.281 10 false Airbag Sensor Assembly 0.354,4.104 1.969,4.333 1.615,0.229 10 false Brake Actuator Assembly 0.604,4.781 1.771,4.99 1.167,0.208 10 false Skid Control ECU 0.427,5.677 1.958,6.083 1.531,0.406 10 false Transmission Revolution Sensor 0.656,6.427 2.427,6.656 1.771,0.229 10 false : CAN Communication Line 5.313,1.229 6.292,1.458 0.979,0.229 10 false Driving Force 5.51,4.542 6.729,5 1.219,0.458 10 false Combination Meter Assembly

HINT:

When the system is operating, even if the driver depresses and holds the accelerator pedal, driving force may increase on an uphill slope and decrease on a downhill slope. This behavior allows the system to restrict the vehicle speed and acceleration below the predetermined limit on slopes and is not a malfunction.



b.

Control during Manual Shift Operation

i.

Responds to shift operations with the accelerator pedal depressed.


ii.

Changes the limit amount according to the manual shift operation pattern.


iii.

Corrects driving force according to the road grade and steering angle.

1.

Control when Starting Off from a Parked Position

Control Start Conditions (When all of the following conditions are met, control starts.)
·

Shift position is changed from P to D, or P to R.

·

Accelerator opening angle is approximately 1/5 or higher.


Control Operation Restricts the driving force so the vehicle speed and acceleration are at or below a certain level.
Control Stop Conditions
·

Shift position is P or N.

·

Accelerator pedal is fully released.



W110518E13
3.615,0.927 3.792,0.771 3.792,0.771 3.99,0.771 true 5.021,1.427 5.146,1.219 5.146,1.219 5.396,1.219 true 5.021,2.323 5.146,2.115 5.146,2.115 5.396,2.115 true 1.563,0.208 2.51,0.542 0.948,0.333 10 false Shift Position 1.354,0.573 2.552,0.948 1.198,0.375 10 false Accelerator Pedal 2.844,0.229 3.073,0.458 0.229,0.229 10 false P 3.406,0.229 3.635,0.458 0.229,0.229 10 false D 2.781,0.573 3.104,0.823 0.323,0.25 10 false ON 4.042,0.698 4.896,1.01 0.854,0.313 10 false Control Start 1.646,1.604 2.563,1.969 0.917,0.365 10 false Driving Force 3.823,2.469 4.229,2.677 0.406,0.208 10 false Time 4.573,1.583 5.385,1.896 0.813,0.313 10 false Restricted 5.448,1.135 6.333,1.49 0.885,0.354 10 false w/o Control 5.448,2.021 6.24,2.406 0.792,0.385 10 false w/ Control

2.

Control when Starting Off from a Parked Position

Control Start Conditions (When all of the following conditions are met, control starts.)
·

Shift position is changed from R to D, D to R, or N to R.

·

Accelerator opening angle is approximately 1/5 or higher.


Control Operation Restricts the driving force so the vehicle speed and acceleration are at or below a certain level.
Control Stop Conditions
·

Shift position is P or N.

·

Accelerator pedal is fully released.



W110519E11
3.573,0.927 3.771,0.771 3.771,0.771 3.979,0.771 true 5,1.406 5.156,1.24 5.156,1.24 5.344,1.24 true 4.927,2.198 5.083,2.031 5.083,2.031 5.271,2.031 true 1.615,0.198 2.573,0.594 0.958,0.396 10 false Shift Position 1.354,0.573 2.5,0.958 1.146,0.385 10 false Accelerator Pedal 4.063,0.708 4.927,1.104 0.865,0.396 10 false Control Start 2.844,0.229 3.052,0.458 0.208,0.229 10 false N 3.406,0.229 3.615,0.458 0.208,0.229 10 false R 2.781,0.573 3.083,0.792 0.302,0.219 10 false ON 1.698,1.604 2.563,1.917 0.865,0.313 10 false Driving Force 3.677,2.469 4.229,2.792 0.552,0.323 10 false Time 4.563,1.552 5.26,1.792 0.698,0.24 10 false Restricted 5.427,1.146 6.24,1.552 0.813,0.406 10 false w/o Control 5.333,1.958 6.229,2.333 0.896,0.375 10 false w/ Control

HINT:
·

The driving force restraint level differs in the above 2 situations.

·

During control while a manual shift operation is performed (from control start until the accelerator pedal is released), the system informs the driver of the control via the multi-information display. For details, refer to the combination meter assembly.






c.

Control during Reverse Operation

i.

Responds to excessive depression of the accelerator pedal while operating in reverse.


ii.

Corrects driving force according to the road grade and steering angle.

Control Start Conditions (When all of the following conditions are met, control starts.)
·

Shift position is R.

·

Accelerator pedal is depressed excessivly.


Control Operation Restricts the driving force so the vehicle speed and acceleration are at or below a certain level.
Control Stop Conditions
·

Shift position is not R.

·

Accelerator pedal is fully released.



W110517E13
3.604,1.063 3.75,0.885 3.75,0.885 3.948,0.885 true 5.031,1.406 5.135,1.177 5.135,1.177 5.375,1.177 true 5.01,2.052 5.115,1.823 5.115,1.823 5.354,1.823 true 1.583,0.208 2.677,0.5 1.094,0.292 10 false Shift Position 1.302,0.573 2.49,0.927 1.188,0.354 10 false Accelerator Pedal 1.667,1.604 2.583,1.802 0.917,0.198 10 false Driving Force 3.802,2.49 4.198,2.708 0.396,0.219 10 false Time 4.542,1.5 5.281,1.698 0.74,0.198 10 false Restricted 5.438,1.104 6.219,1.302 0.781,0.198 10 false w/o Control 3.271,0.573 3.635,0.813 0.365,0.24 10 false ON 2.823,0.229 3.031,0.438 0.208,0.208 10 false R 4.01,0.802 4.969,1.115 0.958,0.313 10 false Control Start 5.417,1.729 6.198,1.927 0.781,0.198 10 false w/ Control