Home › Engine / Hybrid System › 2AR-FE (ENGINE MECHANICAL) › ENGINE UNIT › 2017.09–2021.02
NM33A0E _51 Engine / Hybrid System _067507 2AR-FE ENGINE MECHANICAL _0330095 ENGINE UNIT GE GENERAL F

2AR-FE ENGINE MECHANICAL  ENGINE UNIT  GENERAL  GENERAL  


OUTLINE


a.

The 2AR-FE engine is an in-line 4-cylinder, 2.5 liter, 16 valve DOHC engine. This engine uses a Dual Variable Valve Timing-intelligent (VVT-i) system, Direct Ignition System (DIS), Acoustic Control Induction System (ACIS) and Electronic Throttle Control System-intelligent (ETCS-i). These control functions achieve improved engine performance, fuel economy, and clean emissions.



SPECIFICATION


Engine Type 2AR-FE

*1: Models with single tail exhaust pipe type

*2: Models with dual tail exhaust pipe type

*3: Emission regulations differ depending on the specifications of the vehicle.

*4: The figure shown is the weight of the part without coolant and oil.

No. of Cyls. & Arrangement 4-cylinder, In-line
Valve Mechanism 16-valve DOHC, Chain Drive
(With Dual VVT-i)
Combustion Chamber Pentroof Type
Flow of Intake and Exhaust Gasses Cross-flow
Fuel System SFI
Ignition System DIS
Displacement cm3 (cu. in.) 2494 (152.2)
Bore X Stroke mm (in.) 90.0 X 98.0 (3.54 X 3.86)
Compression Ratio 10.4 : 1
Max. Output (EEC) kW@rpm 133@6000*1
135@6000*2
Max. Torque (EEC) N*m@rpm 231@4100*1
235@4100*2
Valve Timing Intake Open 3° to 38° BTDC
Closed 61° to 26° ABDC
Exhaust Open 60° to 25° BBDC
Closed 4° to 39° ATDC
Spark Plug Type DENSO Made SK16HR11 (Iridium)
Plug Gap mm (in.) 1.0 to 1.1 (0.0394 to 0.0433)
Firing Order 1 - 3 - 4 - 2
Research Octane Number 91 or higher
Emission Regulation*3 EURO IV
EURO V
EURO VI
Engine Service Mass*4 (Reference) kg (lb) 135 (298)

Performance Curve (Models with Single Tail Exhaust Pipe Type)
W104505E07
5.5,0.885 5.76,1.042 0.26,0.156 10 false 140 5.5,1.469 5.76,1.625 0.26,0.156 10 false 120 5.5,2.063 5.76,2.219 0.26,0.156 10 false 100 5.5,2.646 5.698,2.802 0.198,0.156 10 false 80 5.5,3.219 5.698,3.375 0.198,0.156 10 false 60 5.5,3.813 5.698,3.969 0.198,0.156 10 false 40 5.5,4.396 5.698,4.552 0.198,0.156 10 false 20 5.5,4.99 5.594,5.146 0.094,0.156 10 false 0 1.563,2.427 1.823,2.583 0.26,0.156 10 false 240 1.563,2.74 1.823,2.896 0.26,0.156 10 false 220 1.563,3.052 1.823,3.208 0.26,0.156 10 false 200 1.563,3.385 1.823,3.542 0.26,0.156 10 false 180 1.563,3.688 1.823,3.844 0.26,0.156 10 false 160 2.26,5.323 2.604,5.479 0.344,0.156 10 false 1000 2.688,5.323 3.031,5.479 0.344,0.156 10 false 2000 3.125,5.323 3.469,5.479 0.344,0.156 10 false 3000 3.542,5.323 3.885,5.479 0.344,0.156 10 false 4000 3.958,5.323 4.302,5.479 0.344,0.156 10 false 5000 4.396,5.323 4.74,5.479 0.344,0.156 10 false 6000 4.823,5.323 5.167,5.479 0.344,0.156 10 false 7000 1.531,2.083 2.01,2.25 0.479,0.167 10 false (N*m) 3.25,5.531 4.135,5.729 0.885,0.198 10 false Engine Speed 0.896,3.052 1.354,3.229 0.458,0.177 10 false Torque 5.208,5.323 5.604,5.49 0.396,0.167 10 false (rpm) 5.906,2.646 6.375,2.823 0.469,0.177 10 false Output 5.51,0.563 5.854,0.74 0.344,0.177 10 false (kW)

Performance Curve (Models with Dual Tail Exhaust Pipe Type)
W104505E03
5.5,0.888 5.764,1.047 0.264,0.159 10 140 5.5,1.469 5.764,1.628 0.264,0.159 10 120 5.5,2.058 5.764,2.217 0.264,0.159 10 100 5.5,2.644 5.693,2.803 0.193,0.159 10 80 5.5,3.222 5.693,3.381 0.193,0.159 10 60 5.5,3.813 5.693,3.972 0.193,0.159 10 40 5.5,4.395 5.693,4.554 0.193,0.159 10 20 5.5,4.986 5.597,5.145 0.097,0.159 10 0 1.564,2.43 1.828,2.589 0.264,0.159 10 240 1.564,2.741 1.828,2.901 0.264,0.159 10 220 1.564,3.053 1.828,3.213 0.264,0.159 10 200 1.564,3.386 1.828,3.545 0.264,0.159 10 180 1.564,3.691 1.828,3.851 0.264,0.159 10 160 2.262,5.338 2.609,5.493 0.347,0.155 10 1000 2.692,5.338 3.039,5.493 0.347,0.155 10 2000 3.12,5.338 3.466,5.493 0.347,0.155 10 3000 3.539,5.338 3.886,5.493 0.347,0.155 10 4000 3.956,5.338 4.303,5.493 0.347,0.155 10 5000 4.392,5.338 4.739,5.493 0.347,0.155 10 6000 4.827,5.338 5.173,5.493 0.347,0.155 10 7000 1.533,2.081 2.015,2.243 0.483,0.162 10 (N*m) 3.262,5.596 4.156,5.741 0.895,0.145 10 Engine Speed 0.899,3.047 1.356,3.223 0.458,0.175 10 Torque 5.21,5.335 5.604,5.504 0.394,0.169 10 (rpm) 5.904,2.641 6.368,2.823 0.464,0.182 10 Output 5.513,0.566 5.858,0.738 0.346,0.172 10 (kW)


MAIN FEATURES


a.

The 2AR-FE engine has achieved the following through the use of the items listed in the table below.

i.

High performance and reliability


ii.

Low noise and vibration


iii.

Lightweight and compact design


iv.

Good serviceability


v.

Clean emissions and fuel economy

Item i ii iii iv v

*1: Models with tumble control system

*2: Models with smart entry and start system

○: Applicable

-: Not applicable

Engine Proper A cylinder head cover sub-assembly made of aluminum alloy is used. - - ○ - -
A taper squish shape is used for combustion chambers. ○ - - - ○
Spiny-type liners are used in the cylinder bores. ○ - - - -
A cylinder block water jacket spacer is used. ○ - - - ○
The piston skirt is coated with resin. ○ ○ - - ○
Low tension piston rings are used. ○ - - - ○
A resin gear balance shaft is used. - ○ ○ - -
Valve Mechanism The Dual Variable Valve Timing-intelligent (VVT-i) system is used. ○ - - - ○
A chain sub-assembly and No. 1 chain tensioner assembly are used. - ○ - ○ -
Valve lash adjuster assemblies are used. ○ ○ - ○ -
No. 1 valve rocker arm sub-assemblies are used. ○ - - - ○
Lubrication System An oil filter with a replaceable element is used. - - - ○ -
Cooling System TOYOTA Genuine Super Long Life Coolant (SLLC) is used. - - - ○ -
Intake and Exhaust System An intake manifold made of plastic is used. - - ○ - -
A linkless type throttle body with motor assembly is used. - - ○ ○ -
A stainless steel exhaust manifold converter sub-assembly is used. ○ - ○ - ○
An ultra thin-wall, high-cell density ceramic type Three-Way Catalytic converter (TWC) is used. - - - - ○
Fuel System A fuel returnless system is used. - - ○ ○ ○
Quick connectors are used to connect the fuel hoses with the fuel pipes. - - - ○ -
Compact 12-hole type fuel injector assemblies are used. ○ - - - ○
Ignition System The Direct Ignition System (DIS) is used. ○ - ○ ○ ○
Long-reach type iridium-tipped spark plugs are used. ○ - - ○ ○
Charging System A generator clutch pulley with a one-way clutch is used. ○ - - - ○
Serpentine Belt Drive System A serpentine belt drive system is used. - - ○ ○ -
Engine Control System Magnetic Resistance Element (MRE) type camshaft position sensors are used. ○ - - - ○
The Electronic Throttle Control System-intelligent (ETCS-i) is used. ○ - - - ○
An Acoustic Control Induction System (ACIS) is used. ○ - - - -
A tumble control system is used.*1 ○ - - - ○
A cranking hold function is used.*2 ○ - - - -
An evaporative emission control system is used. - - - - ○