Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BODY STRUCTURE › 2017.09–2021.02
NM33A0E _59 Vehicle Exterior _068184 EXTERIOR PANELS / TRIM _0332942 BODY STRUCTURE DE DETAILS F

EXTERIOR PANELS / TRIM  BODY STRUCTURE  DETAILS  SOUND ABSORBING AND VIBRATION DAMPING MATERIAL  


CONSTRUCTION


a.

Sound Absorption and Insulation Structure around Engine Compartment

i.

A hood insulators provided below the hood sub-assembly to suppress engine drive noise which penetrates the cabin and provide excellent quietness.


ii.

A front fender seal and front side air guide sub-assembly are used in the front fender to reduce the noise which travels through the fender toward the cabin.

Y214469C01
2.667,1.667 0.75,2.083 0.75,2.083 0.75,2.75 true 4.583,5.333 5.083,5 5.083,5 5.5,5 true 4.417,4.667 4.917,4.333 4.917,4.333 5.333,4.333 true 0.667,2.771 0.979,2.969 0.313,0.198 10 false *1 5.375,4.26 5.688,4.458 0.313,0.198 10 false *2 5.552,4.948 5.865,5.146 0.313,0.198 10 false *3 0.698,3.938 1.01,4.135 0.313,0.198 10 false *a 5.24,1.5 5.396,1.667 0.156,0.167 10 true A 5.49,2.375 5.646,2.542 0.156,0.167 10 true A
*1 Hood Insulator *2 Front Fender Seal
*3 Front Side Air Guide Sub-assembly - -
*a A - A Cross Section - -



iii.

The dash panel insulator inner is provided in the cabin side, minimizing penetration of engine noise and road noise into the cabin.

Y214480C01
2.667,1.167 2.667,0.583 2.667,0.583 2.917,0.583 true 6,1.583 6.25,1.333 6.25,1.333 6.5,1.333 true 6,2.167 6.25,2.417 6.25,2.417 6.5,2.417 true 2.948,0.51 3.26,0.708 0.313,0.198 10 false *1 4.885,0.438 5.198,0.635 0.313,0.198 10 false *a 6.51,1.229 6.823,1.427 0.313,0.198 10 false *b 6.531,2.302 6.844,2.5 0.313,0.198 10 false *c
*1 Dash Panel Insulator Inner - -
*a Sectional Image *b Soft Felt
*c Olefin Sheet - -
V100136

Noise - -




b.

Sealing Material

i.

Foamed materials, damping foamed materials and sealant are optimally placed in the front header panel, side member opening and rear wheel house to suppress wind noise and road noise which enter the cabin.

Y214468C01
3.188,3.573 3.938,3.667 false 1,1.25 1.25,1 1.25,1 1.417,1 true 4.333,7.5 4.333,7.25 4.333,7.25 4,7 true 0.615,0.292 0.771,0.49 0.156,0.198 10 true A 1.229,0.365 1.385,0.563 0.156,0.198 10 true A 2.198,1.146 2.51,1.344 0.313,0.198 10 false *a 1.354,3.177 1.51,3.375 0.156,0.198 10 true B 1.49,3.573 1.646,3.771 0.156,0.198 10 true B 1.615,2.896 1.771,3.094 0.156,0.198 10 true C 1.948,3.417 2.104,3.615 0.156,0.198 10 true C 0.698,2.625 1.01,2.823 0.313,0.198 10 false *b 1.802,2.615 2.115,2.813 0.313,0.198 10 false *c 3.719,2.521 3.875,2.719 0.156,0.198 10 true D 3.823,3.021 3.979,3.219 0.156,0.198 10 true D 5.417,3.875 5.573,4.073 0.156,0.198 10 true E 6.573,3.354 6.729,3.552 0.156,0.198 10 true E 3.01,3.479 3.167,3.677 0.156,0.198 10 true F 4.031,3.615 4.188,3.813 0.156,0.198 10 true F 4.344,4.677 4.5,4.875 0.156,0.198 10 true G 4.354,5.125 4.51,5.323 0.156,0.198 10 true G 3.219,2.385 3.531,2.583 0.313,0.198 10 false *d 1.979,6.156 2.292,6.354 0.313,0.198 10 false *f 5.406,2.115 5.719,2.313 0.313,0.198 10 false *e 5.073,6.115 5.385,6.313 0.313,0.198 10 false *g 1.448,0.906 1.76,1.104 0.313,0.198 10 false *1 4.229,7.51 4.542,7.708 0.313,0.198 10 false *2
*1 Front Header Panel *2 Rear Wheel House
*a A - A Cross Section *b B - B Cross Section
*c C - C Cross Section *d D - D Cross Section
*e E - E Cross Section *f F - F Cross Section
*g G - G Cross Section - -
V100145

Foamed Material
V100155

Damping Foamed Material




c.

Floor Silencer

i.

The floor silencer (applied damping materials) optimal thickness varies by the area, is lightweight and provides excellent quietness. These characteristics allow the floor silencer to reduce road and engine noise which enters the cabin.

Y214482C01
2.094,0.906 2.083,0.865 false
V100145

Applied Damping Materials - -