FUNCTION OF MAIN COMPONENTS
The main components in the RSA have the following functions.
| Item | Function | |
|---|---|---|
|
*: The threshold can be adjusted to 1 of 3 levels through the customization function |
||
| Forward Recognition Camera | ·
Captures road signs. ·
Performs RSA system control based on information of road signs captured by the monocular camera sensor. |
|
| Camera Heater (Forward Recognition Hood) | The camera heater is heated according to signals from the forward recognition camera. | |
| Airbag Sensor Assembly | Yawrate Sensor | Detects the yaw rate and lateral/longitudinal deceleration of the vehicle and transmits the signal to the forward recognition camera. |
| Combination Meter Assembly | Multi-information Display | ·
Displays road signs recognized by the forward recognition camera. ·
The RSA system can be turned on and off through the settings tab. |
| Buzzer | Sounds for speed limit exceeded and no overtaking notifications.* | |
| Steering Pad Switch Assembly | Meter Control Switch | Sends a multi-information operating signal to the forward recognition camera. |
| Steering Sensor | Detects the angle and direction of steering and transmits signals to the forward recognition camera. | |
| Turn Signal Switch | Sends a turn signal command to the steering sensor. | |
| ECM | Sends a shift position signal to the forward recognition camera. | |
| Brake Actuator Assembly | Skid Control ECU | Sends a vehicle speed signal from the speed sensor to the forward recognition camera. |
| Speed Sensor | Detects the vehicle speed and transmits a signal via the skid control ECU to the forward recognition camera. | |
| Main Body ECU (Multiplex Network Body ECU) | Sends country specification information signals to the forward recognition camera. | |
| Air Conditioning Amplifier Assembly | Sends the outside temperature signal to the forward recognition camera. | |
| Central Gateway ECU (Network Gateway ECU) | Gateway function of CAN communication. | |
FUNCTION
The RSA system recognizes the following traffic signals using the forward recognition camera.
| Category | Sign Type | Example of Recognizable Sign | |
|---|---|---|---|
| Speed Limit | Round maximum speed limit/End of speed limit |
|
|
| No Overtaking | No overtaking/End of no overtaking |
|
|
| Supplemental Signs | Road condition signs | Ramp Way |
|
| Rain |
|
||
| Wet |
|
||
| Ice |
|
||
| End of Prohibition |
|
||
| Information signs related speed limit | Motorway sign (entrance, exit) |
|
|
The RSA system recognizes the following traffic signals using the forward recognition camera.
| Category | Display Example | Details | |
|---|---|---|---|
| Speed Limit Related |
|
·
Informs the driver of the maximum speed limit of the currently driven road. ·
The displayed sign reflects the speed limit on the recognized sign. |
|
|
Informs the driver highway sign (entrance, exit). | ||
| No Overtaking Related |
|
Informs the driver when they are in a no overtaking zone on the currently driven road. | |
| All Canceled (All restrictions canceled. Return to default road regulations.) |
|
Informs the driver when all applicable prohibitions, such as speed limit and no overtaking, have ended. | |
| Speed Limit with Supplemental Sign Related | Ramp Way |
|
Informs the driver of the ramp way direction. However, this item is not displayed when making a lane change without operating the turn signal light. |
| Rain |
|
Informs the driver of the maximum speed limit on the currently driven road when it is raining or the road surface is wet. | |
| Speed Limit with Supplemental Sign Related | Ice |
|
Informs the driver of the maximum speed limit on the currently driven road when there is accumulated snow or ice. |
| Blank |
|
The display is blank when the system is unable to recognize a supplemental sign. |
Notification functions are used in the RSA system which invert the colors of displayed signs, flash signs, etc. to notify the driver.
Speed Limit Exceeded Notification
While a speed limit sign is displayed, if the actual vehicle speed exceeds the speed limit plus a designated threshold*, the colors of the displayed sign are inverted. For example, if the threshold is set to 5 km/h and the speed limit sign is 60 km/h, the colors of the displayed sign are inverted when the actual vehicle speed exceeds 65 km/h. Furthermore, the system also inverts a speed limit sign with supplemental sign in the same way. However, the system does not invert the colors of the supplemental sign.
The buzzer may be set to sound during notifications through the customization function. However, if a speed limit recognized from a speed limit with supplemental sign is exceeded, the buzzer does not sound.
*: The threshold can be adjusted to 1 of 3 levels through the customization function.
| Notification Method | Display Example |
|---|---|
| Inverted Display |
|
No Overtaking Notification
While a no overtaking sign is displayed, if the system detects that the vehicle is attempting to overtake another vehicle, the system flashes the displayed sign.
The buzzer may be set to sound during notifications through the customization function.
| Notification Method | Display Example |
|---|---|
| Flashing Display |
|
The RSA can be turned on or off through the settings tab of the multi-information display.
A customization function is used for the RSA, which allows settings such as the notification method and level for exceeding the speed limit to be changed. Setting changes are made through the customization tab of the multi-information display. Refer to the Repair Manual for details.
SYSTEM CONTROL
RSA Control Pattern 1
After a road sign is recognized by the forward recognition camera and the vehicle passes by, the sign is displayed on the multi-information display.
While a sign is displayed on the multi-information display, if a new road sign is not recognized within a specified distance, display of the current sign is turned off.
RSA Control Pattern 2
When the engine switch is turned off while a sign is displayed on the multi-information display, the same sign is displayed when the engine switch is turned ON again.
RSA Control Pattern 3
While a sign is displayed on the multi-information display, the sign is turned off when turning left or right onto a new road.
DIAGNOSIS
If a malfunction is detected in the RSA system the forward recognition camera. cancels the RSA, sounds the buzzer in the combination meter assembly, and displays a message on the multi-information display to inform the driver of the malfunction.
At the same time, the malfunction is stored in memory as a Diagnostic Trouble Code (DTC). When a Global TechStream (GTS) is connected to the DLC3, the DTC can be read. For details, refer to the Repair Manual.