Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › from 2017.12
NM33A0E _58 Vehicle Interior _067429 HEATING / AIR CONDITIONING _0329256 AIR CONDITIONING SYSTEM GE GENERAL F

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  GENERAL  GENERAL  


OUTLINE


a.

Both manual and automatic air conditioning systems are available.


b.

The automatic air conditioning system uses left and right independent temperature control and neural network control to enhance comfort.


c.

An inside-and-outside dual air layer type air conditioning unit is provided depending on the model.


d.

HFC-134a refrigerant is used.


e.

The automatic air conditioning system uses driver, front passenger and rear passenger* independent temperature control to enhance comfort.

*: Models with 3-zone control



SPECIFICATION


a.

Ventilation and Heater Core

*1: Models with dual air layer type air conditioning unit

*2: Models with single air layer type air conditioning unit

Heater Radiator Unit Sub-assembly Type Straight Flow Aluminum (SFA)-II
Size (W x H x L) mm (in.) 263.9 x 120 x 27
(10.4 x 4.7 x 1.1)
Blower with Fan Motor Sub-assembly*1 Motor Type DC Ferrite Brushless
Fan Type Semi Sirocco
Fan Size (Dia. x H) mm (in.) Upper Side: 122.0 x 55.0 (4.8 x 2.2)
Lower Side: 125.0 x 38.0 (4.9 x 1.5)
Blower with Fan Motor Sub-assembly*2 Motor Type DC Ferrite Brushless
Fan Type Semi Sirocco
Fan Size (Dia. x H) mm (in.) 137.0 x 70.0 (5.4 x 2.8)


b.

Air Conditioning

*1: Except models with 2GR-FKS engine

*2: Models with 2GR-FKS engine

Cooler Condenser Assembly Type Global Inner-fin Condenser (GIC)
Size (W x H x L) mm (in.) 700 x 453 x 11.5
(27.6 x 17.8 x 0.5)
Fin Pitch mm (in.) 3.0 (0.12)
Compressor with Pulley Assembly*1 Type 7SES17C
Pulley Plastic Damper Limiter (DL)
Compressor with Pulley Assembly*2 Type 7SAS17C
Pulley Steel with Magnet Clutch
Refrigerant Type HFC-134a
Evaporator Type Beneficial Refrigerant Stream (BRS) Evaporator
Size (W x H x L) mm (in.) 279.7 x 231.0 x 38.0 (11.0 x 9.1 x 1.5)
Fin Pitch mm (in.) 3.0 (0.12)



MAIN FEATURES


a.

The air conditioning system has the following features:

High Performance
·

Neural network control is used so passengers can finely control the air conditioning for maximum comfort.

·

A high efficiency type clean air filter, which has a pollen-and-odor removal effect, is used.

·

The blower control has 7 steps to allow precise control.

·

Using the following features of the compressor (continuously variable capacity compressor), high cooling performance and a quiet cabin have been achieved:

-

Oil Separator

-

Variable Suction Side Throttle

-

Solenoid Valve with Built-in Crank Chamber to Suction Passage (CS) Valve



Lightweight
·

An air conditioning harness assembly with a built-in communication/driver IC is used in a lightweight wire harness design to allow a reduced number of wires.

·

The use of this type of connector means that pulse pattern type servo motors can be used.


Others The following parts are used to ensure high cooling performance while realizing a compact and lightweight construction.
·

Semi-center Location Air Conditioning Unit

·

Beneficial Refrigerant Stream (BRS) Evaporator

·

Straight Flow Aluminum (SFA)-II Heater Radiator Sub-assembly

·

Global Inner-fin Condenser (GIC) Sub-cool Condenser