Home › Engine / Hybrid System › 6AR-FSE (ENGINE CONTROL) › SFI SYSTEM › 2018.04–2021.02
NM33A0E _51 Engine / Hybrid System _072440 6AR-FSE ENGINE CONTROL _0351695 SFI SYSTEM CO CONTROL F

6AR-FSE ENGINE CONTROL  SFI SYSTEM  CONTROL  DIRECT INJECTION 4-STROKE GASOLINE ENGINE SUPERIOR VERSION SEQUENTIAL MULTIPORT FUEL INJECTION (D-4S SFI)  


FUNCTION


a.

The D-4S system is a fuel injection system which combines direct injection injectors and port injection injectors.


b.

The mass air flow meter sub-assembly detects intake air volume to control fuel injection volume.


c.

Based on signals from each sensor, the ECM controls the injection volume and timing of each type of fuel injector assembly (direct and port injection types) in accordance with engine load and engine speed in order to optimize combustion conditions.


d.

To promote warm-up of the catalyst after a cold engine start, this system uses a stratified air fuel mixture. This creates an area near the spark plug that is richer than the rest of the air fuel mixture. This also allows a greater amount of ignition timing retard to be used, raising the exhaust gas temperature. The increased exhaust gas temperatures promote rapid warm-up of the catalysts, significantly reducing exhaust emissions.


e.

When the engine is idling after warm-up, the port fuel injector assembly is used to inject fuel, ensuring quietness.

Fuel Injection System Activation Ranges
W113131E02
4.813,1.281 5.104,0.677 5.104,0.677 5.26,0.677 true 3,1.417 3.417,0.635 3.417,0.635 3.573,0.635 true 1.177,1.208 1.948,1.406 0.771,0.198 10 false Heavy 0.365,1.646 1.24,1.854 0.875,0.208 10 false Engine Load 1.74,2.031 2.854,2.469 1.115,0.438 10 false Direct Injection or Port Injection 3.5,3.094 4.427,3.313 0.927,0.219 10 false Engine Speed 4.448,2.865 5.219,3.063 0.771,0.198 10 false High 5.333,0.563 6.417,0.844 1.083,0.281 10 false Direct Injection 3.646,0.458 4.74,0.896 1.094,0.438 10 false Direct Injection + Port Injection 1.25,2.021 1.625,2.292 0.375,0.271 10 false Light 3.208,2.865 3.979,3.063 0.771,0.198 10 false Low


f.

Stratified Combustion: To achieve stratified combustion, immediately after a cold engine start, fuel is injected into the intake port from the port fuel injector assembly during the exhaust stroke. Fuel is also injected from the direct fuel injector assembly near the end of the compression stroke. This results in an air fuel mixture that is stratified, and the area near the spark plug is richer than the rest of the air fuel mixture. This allows a retarded ignition timing to be used, raising the exhaust gas temperature. The increased exhaust gas temperatures promote rapid warm up of the catalysts, and significantly improve exhaust emission performance.

W113142E06
1.667,6 2.458,4.26 2.458,4.26 2.583,4.26 true 2.646,4.188 3.896,4.615 1.25,0.427 10 false Combustion Mixture Layer 0.792,2.76 2.542,2.958 1.75,0.198 10 false Expansion to Intake Stroke 4.938,2.771 5.927,2.969 0.99,0.198 10 false Intake Stroke 0.302,3.135 3.24,3.656 2.938,0.521 10 false Fuel is injected into the intake port from the port fuel injector assembly before the intake valves open. 3.74,3.146 6.865,3.563 3.125,0.417 10 false The intake valves open and a homogeneous air fuel mixture is drawn into the combustion chamber. 0.792,6.594 2.635,6.865 1.844,0.271 10 false Ignition to Combustion Stroke 4.677,6.594 6.073,6.854 1.396,0.26 10 false Compression Stroke 0.25,6.917 3.323,7.823 3.073,0.906 10 false Injected fuel is directed along the piston contour to the area near the spark plug. This produces a combustible area of rich air fuel mixture that allows for easy ignition. This allows combustion of a lean air fuel mixture to occur. 4,6.927 6.792,7.521 2.792,0.594 10 false Fuel is injected into the combustion chamber from the direct fuel injector assembly near the end of compression stroke. 0.094,8.521 2.927,8.75 2.833,0.229 10 false This illustrations shown are examples only.


g.

Homogeneous Combustion: To optimize combustion conditions, the ECM controls injection volume and timing of the port fuel injector assemblies which inject fuel into the intake ports during the expansion, exhaust, and intake strokes. The ECM also controls the injection volume and timing of the direct fuel injector assemblies which inject fuel during the first half of the intake stroke. The homogeneous air fuel mixture is created by either combined or individual use of the 2 different types of injectors. This allows utilization of the evaporation heat of the injected fuel to cool the compressed air, and it also allows an increase of charging efficiency and power output.

W113143E05
3.844,7.615 6.958,8.031 3.115,0.417 10 false The homogeneous air fuel mixture is compressed. 3.688,2.74 6.906,3.635 3.219,0.896 10 false The intake valves open to allow the homogeneous air fuel mixture into the combustion chamber, and fuel is injected into the combustion chamber from the direct fuel injector assembly during the first half of the intake stroke. 3.698,4.448 6.823,4.917 3.125,0.469 10 false The injected fuel and air are evenly mixed by intake air force. 4.656,7.26 6.188,7.469 1.531,0.208 10 false Compression Stroke 0.688,7.25 2.563,7.479 1.875,0.229 10 false Ignition to Combustion Stroke 4.854,2.323 5.948,2.563 1.094,0.24 10 false Intake Stroke 0.781,2.344 2.583,2.563 1.802,0.219 10 false Expansion to Intake Stroke 0.313,7.604 3,7.969 2.688,0.365 10 false The spark plug ignites the homogeneous air fuel mixture. 0.177,2.76 3.135,3.365 2.958,0.604 10 false Fuel is injected into the intake port from the port fuel injector assembly before the intake valves open. 0.083,8.438 2.771,8.802 2.688,0.365 10 false This illustrations shown are examples only.


h.

Air Fuel Ratio Control

i.

Fuel injection volume is determined based on the engine speed and the intake air volume. In addition, feedback control is performed for the air fuel ratio after engine start based on the signal from the air fuel ratio sensor.

Control Combustion State Air Fuel Ratio Injection Timing* Precondition
Lean air fuel ratio control Stratified Combustion 15 to 17 : 1 Compression Stroke Immediately after cold engine start
Stoichiometric air fuel ratio control Homogeneous Combustion 14 to 15 : 1 Intake Stroke Low to mid-load driving
Air fuel ratio feedback control prohibition Homogeneous Combustion - Intake Stroke High-load driving
Cold engine

*: Of the direct fuel injector assembly. The port fuel injector assembly performs respective control to inject fuel from the expansion stroke to the intake stroke in accordance with the engine running conditions.



i.

Fuel Cut

i.

When the engine speed exceeds the specified value, fuel injection is stopped to prevent over-revving.

Engine Speed for Fuel-cut at High Revs
Engine speed (rpm) 6800 or more