Home › Engine / Hybrid System › 6AR-FSE (ENGINE MECHANICAL) › ENGINE UNIT › 2018.04–2021.02
NM33A0E _51 Engine / Hybrid System _072441 6AR-FSE ENGINE MECHANICAL _0351748 ENGINE UNIT DE DETAILS F

6AR-FSE ENGINE MECHANICAL  ENGINE UNIT  DETAILS  BALANCE SHAFT  


CONSTRUCTION


a.

An engine balancer assembly is used to reduce vibration. An engine balancer assembly is used to reduce vibration. The inertial mass of the weight inside the engine balancer assembly is optimized, reducing the muffled sound inside the vehicle cabin.


b.

The crankshaft directly drives the No. 1 balance shaft.


c.

In addition, a resin gear is used on the driven side to suppress noise and offer a lightweight design.


d.

The engine balancer assembly is separated from the stiffening crankcase assembly, thus making it easier to be serviced. Additionally, the engine balancer assembly is fastened to the highly-rigid cylinder block sub-assembly with bolts through the stiffening crankcase assembly, reducing the weight of the stiffening crankcase assembly, noise and vibrations.

W124990C02
2.594,1.396 2.25,0.594 2.25,0.594 2.031,0.594 true 3.177,1.01 2.833,0.208 2.833,0.208 2.615,0.208 true 4.021,3.177 4.365,2.448 4.365,2.448 4.594,2.448 true 2.688,3.604 2.344,2.802 2.344,2.802 2.125,2.802 true 2.406,3.927 2.063,3.125 2.063,3.125 1.844,3.125 true 3.448,4.302 3.688,3.823 3.688,3.823 3.917,3.823 true 4.219,4.333 4.458,3.854 4.458,3.854 4.688,3.854 true 4.302,5.865 4.375,6.479 4.375,6.479 4.604,6.479 true 1.823,0.49 2.135,0.646 0.313,0.156 10 false *1 4.646,2.354 4.958,2.51 0.313,0.156 10 false *2 1.646,3.021 1.958,3.177 0.313,0.156 10 false *3 4.729,3.771 5.042,3.927 0.313,0.156 10 false *4 4.646,6.375 4.958,6.531 0.313,0.156 10 false *5 2.396,0.115 2.708,0.271 0.313,0.156 10 false *a 1.917,2.708 2.229,2.865 0.313,0.156 10 false *b 3.958,3.708 4.271,3.865 0.313,0.156 10 false *c
*1 Crankshaft *2 No. 2 Balance Shaft Housing
*3 No. 2 Balance Shaft *4 No. 1 Balance Shaft
*5 No. 1 Balance Shaft Housing - -
*a Balance Shaft Drive Gear *b Resin Gear
*c Balance Shaft Driven Gear (Resin Gear) - -



e.

In an in-line 4-cylinder engine, the crankshaft angle for cylinders No. 1 and No. 4 is exactly the opposite (180°) from the position of cylinders No. 2 and No. 3. Therefore, the inertial force of the pistons and the connecting rods of the former 2 cylinders and of the latter 2 cylinders almost cancels each other out. However, because the position at which the piston reaches its maximum speed is located toward top dead center from the center of the stroke, the upward inertial force is greater than the downward inertial force. This unbalanced secondary inertial force is generated twice for each rotation of the crankshaft.

Inertial Force Generated by In-line 4 Cylinders
W125946C01
1.656,0.563 2.177,0.563 false 1.625,0.927 2.156,0.927 false 1.646,1.646 2.177,1.646 false 4.896,1.302 5.208,0.51 5.208,0.51 5.385,0.51 true 2.25,0.5 2.563,0.656 0.313,0.156 10 false *a 2.25,0.865 2.563,1.021 0.313,0.156 10 false *b 2.26,1.563 2.573,1.719 0.313,0.156 10 false *c 3.615,1.042 3.927,1.198 0.313,0.156 10 false *d 3.625,1.573 3.938,1.729 0.313,0.156 10 false *e 3.646,2.313 3.958,2.469 0.313,0.156 10 false *f 4.573,0.563 4.885,0.802 0.313,0.24 10 false *g 6.802,1.854 7.115,2.01 0.313,0.156 10 false *h 5.427,0.427 5.75,0.625 0.323,0.198 10 false *i 3.76,2.958 4.073,3.177 0.313,0.219 10 false *j 4.26,2.979 4.573,3.135 0.313,0.156 10 false *k 4.74,2.969 5.052,3.125 0.313,0.156 10 false *l 5.167,2.969 5.479,3.125 0.313,0.156 10 false *m 5.719,2.969 6.031,3.125 0.313,0.156 10 false *n 6.24,2.969 6.552,3.125 0.313,0.156 10 false *o 2.229,2.094 2.542,2.25 0.313,0.156 10 false *b 0.885,2.083 1.198,2.24 0.313,0.156 10 false *b
*a Top Dead Center *b Point of Max. Speed
*c Bottom Dead Center *d Inertial Force of Cylinders No. 2 and No. 3
*e Combined Inertial Force of All Cylinders
(Unbalanced Secondary Inertial Force)
*f Inertial Force of Cylinders No. 1 and No. 4
*g Force *h Crankshaft Angle
*i Inertial force that cannot be canceled *j -180°
*k -90° *l 0°
*m 90° *n 180°
*o 270° - -



f.

To cancel the unbalanced secondary inertial force, 2 balance shafts are provided that rotate twice for each rotation of the crankshaft. By doing this they generate an inertial force in the opposite direction. Also, in order to cancel the inertial force generated by the balance shafts themselves, there are actually 2 shafts rotating in opposite directions.

Inertial Force of Balance Shafts
W100813C10
6.125,0.688 6.625,0.688 false 6.052,1.802 6.656,1.802 false 4.198,3.01 4.198,2.396 4.198,2.396 4.792,2.396 true 4.063,3.188 4.802,3.188 true 0.583,1.323 0.771,1.479 0.188,0.156 10 false *a 2.281,1.323 2.49,1.5 0.208,0.177 10 false *b 3.969,1.323 4.177,1.51 0.208,0.188 10 false *c 5.677,1.323 5.885,1.51 0.208,0.188 10 false *d 6.677,0.594 6.906,0.76 0.229,0.167 10 false *e 6.677,1.146 6.865,1.375 0.188,0.229 10 false *f 6.698,1.719 6.875,1.917 0.177,0.198 10 false *g 4.833,2.323 5.031,2.469 0.198,0.146 10 false *h 4.833,3.094 5.063,3.271 0.229,0.177 10 false *e
*a 0° *b 90°
*c 180° *d 270°
*e Inertial Force of Balance Shafts *f Crankshaft Angle
*g Secondary Inertial Force *h Mass Direction of Balance Shaft