Home › Engine / Hybrid System › M20A-FKS (ENGINE MECHANICAL) › ENGINE UNIT › from 2021.02
NM33A0E _51 Engine / Hybrid System _098546 M20A-FKS ENGINE MECHANICAL _0461151 ENGINE UNIT DE DETAILS F

M20A-FKS ENGINE MECHANICAL  ENGINE UNIT  DETAILS  CYLINDER BLOCK  


CONSTRUCTION


a.

An aluminum cylinder block sub-assembly is used to achieve a lightweight design.


b.

The liners are a spiny-type, which have been manufactured so that their casting exteriors form large irregular surfaces in order to enhance the adhesion between the liners and the aluminum cylinder block sub-assembly. The enhanced adhesion helps heat dissipation, resulting in a lower overall temperature and reduced heat deformation of the cylinder bores.


c.

By eliminating the No. 1 cylinder front side water jacket from the cylinder block sub-assembly, the overall length of the engine has been compressed to achieve a more compact design.


d.

By positioning the water jackets adjacent to the oil drain passages, heat transfer between them has been enhanced. With this, cold engine warm-up capability is enhanced and excessive oil temperatures are reduced when the engine load is high, ensuring vehicle reliability.


e.

Water passages are drilled between each cylinder bore to provide increased cooling to the upper part of the cylinder bore which is most susceptible to heat. This minimizes deformation of the cylinder bore, ensuring high power output and reduced oil consumption.


f.

A larger breather hole is provided in the No. 1 to No. 4 journal wall. As a result, friction is reduced and output performance is improved.


g.

The angle of the bore cross hatching, the polishing on the cylinder liner surface, is at an angle of 30°, improving the oil retention of the interior of the cylinder bore. This reduces the friction between the cylinder bore and the piston, improving fuel consumption.


h.

The shape of the ribs, and the positioning and shape of the knock control sensor have been optimized, improving control of knocking.

W140378C01
1.26,1.156 1.427,0.323 1.427,0.323 1.594,0.323 true 0.938,1.104 0.771,0.521 0.771,0.521 0.604,0.521 true 1.698,1.156 1.865,0.323 1.865,0.323 2.031,0.323 true 2.115,1.146 2.281,0.313 2.281,0.313 2.448,0.313 true 2.552,1.156 2.719,0.323 2.719,0.323 2.885,0.323 true 5.146,4.906 5.333,4.667 5.333,4.667 5.5,4.667 true 5.125,5.885 5.333,6.531 5.333,6.531 5.5,6.531 true 4.792,1.354 4.948,1.938 4.948,1.938 5.115,1.938 true 4.792,0.458 4.906,0.156 4.906,0.156 5.073,0.156 true 5.229,3.396 5.563,3.646 5.563,3.646 5.729,3.646 true 5.188,3.01 5.646,3.01 true 4.469,3.49 4.625,3.49 4.625,3.49 5.094,3.125 true 0.427,0.427 0.74,0.583 0.313,0.156 10 false *1 5.135,0.063 5.448,0.219 0.313,0.156 10 false *b 5.177,1.854 5.49,2.01 0.313,0.156 10 false *d 5.552,0.719 5.823,0.938 0.271,0.219 10 false *c 3.917,4.531 4.219,4.76 0.302,0.229 10 false *i 5.531,4.573 5.844,4.729 0.313,0.156 10 false *f 5.542,6.406 5.771,6.635 0.229,0.229 10 false *j 1.625,0.198 1.844,0.417 0.219,0.219 10 false *a 6.781,1.031 7.052,1.25 0.271,0.219 10 false 30° 1.625,6.313 1.938,6.469 0.313,0.156 10 false B 1.5,1.583 1.813,1.74 0.313,0.156 10 false A 2.073,0.198 2.292,0.417 0.219,0.219 10 false *a 2.49,0.198 2.708,0.417 0.219,0.219 10 false *a 2.927,0.208 3.146,0.427 0.219,0.219 10 false *a 2.188,1.583 2.5,1.74 0.313,0.156 10 false A 1.625,4.74 1.938,4.896 0.313,0.156 10 false B 5.688,2.917 6,3.073 0.313,0.156 10 false *f 5.781,3.542 6.073,3.792 0.292,0.25 10 false *h 4.302,3.375 4.531,3.594 0.229,0.219 10 false *g 3.885,2.24 4.198,2.396 0.313,0.156 10 false *e
*1 Cylinder Block Sub-assembly - -
*a Oil Drain Passage *b Cylinder Bore
*c Bore Cross Hatch *d Spiny-type Liner (Irregularly Shaped Outer Casting Surface of Liner)
*e A-A Cross Section *f Water Passage
*g Cylinder Liner Circumference Treatment *h Thermal Spray Aluminum Coating
*i B-B Cross Section *j Larger Breather Hole



i.

Through the use of an offset crankshaft, the centerline of the bores is shifted 10 mm (0.394 in.) towards the intake side in relation to the centerline of the crankshaft. As a result, the side force to the cylinder wall is reduced when the maximum pressure is applied. This contributes to fuel economy.

W140379C01
4.219,3.052 4.385,3.052 4.385,3.052 4.719,2.469 true 5.552,3.052 5.719,3.052 5.719,3.052 6.052,2.469 true 1.885,0.74 2.198,0.896 0.313,0.156 10 false *a 1.833,2.917 2.146,3.073 0.313,0.156 10 false *b 2.844,0.927 3.156,1.083 0.313,0.156 10 false *c 0.885,0.927 1.198,1.083 0.313,0.156 10 false *d 4.75,0.594 5.063,0.75 0.313,0.156 10 false *e 4.771,3.25 5.083,3.406 0.313,0.156 10 false *f 6.135,3.25 6.396,3.521 0.26,0.271 10 false *g 5.958,0.594 6.271,0.75 0.313,0.156 10 false *e 4.052,2.958 4.365,3.115 0.313,0.156 10 false *b 5.375,2.958 5.688,3.115 0.313,0.156 10 false *b
*a Bore Centerline *b Crankshaft Center
*c Intake Side *d Exhaust Side
*e Maximum Pressure *f Offset Crankshaft
*g Non-offset Crankshaft - -