Home › Drivetrain › K120 (CVT) › CVT SYSTEM › from 2021.02
NM33A0E _52 Drivetrain _099232 K120 CVT _0463353 CVT SYSTEM CO CONTROL F

K120 CVT  CVT SYSTEM  CONTROL  CVT CONTROL  


FUNCTION OF MAIN COMPONENTS


a.

The main components of the K120 Continuously Variable Transaxle (CVT) are as follows:

Component Function
Continuously Variable Transaxle Assembly Linear Solenoid Valve SLS Controls the oil pressure of the secondary pulley in accordance with the input shaft torque to control belt clamping force.
Linear Solenoid Valve SLP Controls the oil pressure of the primary pulley in accordance with the vehicle speed and accelerator pedal position signals to control the speed ratio.
Linear Solenoid Valve SLU Performs lock-up clutch control.
Linear Solenoid Valve SL1 Controls the C1 clutch for gear mode.
Linear Solenoid Valve SL2 Controls the C2 clutch for belt mode.
Linear Solenoid Valve SLG Controls the synchronizer mechanism and B1 brake (reverse).
Transmission Revolution Sensor (NC1) Detects the No.1 drive gear speed.
Transmission Revolution Sensor (NT) Detects the primary pulley speed.
Transmission Revolution Sensor (NSS) Detects the secondary pulley speed.
Transmission Revolution Sensor (NOUT) Detects the output speed.
CVT Fluid Temperature Sensor (Transmission Wire) Detects the CVT fluid temperature.
Oil Pressure Sensor Detects the steel belt clamping force.
Clutch Stroke Sensor Detects the shift fork position.
Engine Coolant Temperature Sensor Detects the engine coolant temperature.
Throttle Body with Motor Assembly Throttle Position Sensor Detects the opening angle of the throttle valve.
Mass Air Flow Meter Sub-assembly Intake Air Temperature Sensor Detects the intake air volume and intake air temperature.
Airbag Sensor Assembly Yawrate Sensor Detects the vehicle's yaw rate.
Acceleration Sensor Detects the vehicle's longitudinal and lateral acceleration and deceleration.
Stop Light Switch Assembly Detects the brake pedal depressing signal.
Park/Neutral Position Switch Assembly Detects the shift lever position.
Transmission Floor Shift Assembly Transmission Control Switch Detects when the shift lever is in M.
Crank Position Sensor Detects the engine speed.
Accelerator Pedal Sensor Assembly Detects the accelerator pedal opening angle.
Air Conditioning Amplifier Assembly Transmits the operating state of the air conditioning system.
Transmission Control ECU Drives each solenoid valve based on signals from each sensor and switch and optimally controls the CVT.
Combination Meter Assembly Multi-information Display
·

Displays the shift lever position.

·

Displays the shift range.


Malfunction Indicator Lamp (MIL) Illuminates to inform the driver when the transmission control ECU detects a malfunction.
Buzzer Sounds when shift-down operation is rejected in 10-speed sport sequential shiftmatic mode.
Brake Actuator Assembly Skid Control ECU Sends the information about the operation conditions of the brake control system to the transmission control ECU.



SYSTEM CONTROL


a.

Control List

i.

The electronic control system of the K120 CVT consists of the controls listed below.

Control Outline
Engine-CVT Integrated Control Effects coordinate control of the CVT system and engine control system to ensure both smooth and powerful driving that excels in shift response and fuel economy.
Automatic Shift Control (Speed Ratio Control) Controls the primary pulley speed to approach the calculated target input rotation speed based on information such as the accelerator pedal position, vehicle speed and stop light switch signals.
Acceleration Improvement Control Controls the acceleration rate in proportion to the accelerator pedal position, improving the feeling of linear acceleration and expanding the feeling of accelerator pedal input.
Deceleration Improvement Control Determines a pulley ratio which allows for high engine speed to be maintained during deceleration, thus ensuring adequate engine braking.
10-speed Sport Sequential Shiftmatic Enables driving in a specific shift range which is selected using the shift lever providing engine braking force appropriate to each shift range.
Uphill/Downhill Shift Control Uses the transmission control ECU to determine whether the vehicle is traveling uphill or downhill in order to restrict upshifts or provide appropriate engine braking force by using downshifts.
Flex Lock-up Control By enhancing the lock-up operation range into the low vehicle speed range, the fuel cut range has been enlarged, achieving improved fuel economy.
Clutch Capacity Control When driving in belt mode, and sudden braking causes excessive input forces from the road surface, the C2 clutch performs torque capacity control to protect the belt by limiting the load applied to it.



b.

Engine - CVT Integrated Control

i.

To effect fine-tuned control in accordance with driving conditions, various signals are exchanged between the engine control system and the CVT system. As a result, both smooth and powerful driving that excels in shift response and fuel economy has been achieved.



c.

Automatic Shift Control (Speed Ratio Control)

i.

The transmission control ECU determines the driving conditions through each input signal and selects the optimal control to achieve output which meets the driver's intentions.

X140535E10
2.542,0.188 5.552,0.458 3.01,0.271 10 false Acceleration Improvement Control 0.417,1.083 2.042,1.479 1.625,0.396 10 false Deceleration Improvement Control 5.094,0.917 6.771,1.74 1.677,0.823 10 false 10-speed Sport Sequential Shiftmatic 2.333,2.198 5.344,2.469 3.01,0.271 10 false Shift Control in Uphill/Downhill Traveling 2.76,1.083 4.323,1.5 1.563,0.417 10 false Gear/ Belt Shift Control + Automatic Shift Control


ii.

When the shift lever is in D, the system effects engine integrated control to optimize fuel economy characteristics and driving performance.


iii.

When the shift lever is in M, if the vehicle reaches the set speed when accelerating, the system automatically upshifts.



d.

Acceleration Improvement Control (Gentle acceleration: Low accelerator opening angle range)

i.

While proactively using the high efficiency range to improve fuel economy performance, it is possible to accelerate with smooth shifting that prevents the occupants from feeling the series of operations that include switching from gear mode to belt mode (clutch to clutch), lock-up engagement, and synchronizer engagement.

X140538E02
2.958,1.521 4.76,1.135 4.76,1.135 4.938,1.135 true 2.094,3.26 2.271,3.26 2.271,3.26 2.75,2.885 true 3.24,0.667 5.99,0.865 2.75,0.198 10 false Pulley Ratio (Low) 4.99,1.063 6.135,1.344 1.146,0.281 10 false Gear/ Belt Shift 4.792,1.802 6.552,2.052 1.76,0.25 10 false Pulley Ratio (High) 3.99,2.479 5.75,2.729 1.76,0.25 10 false High Fuel Economy Area 3.167,3.073 4.927,3.323 1.76,0.25 10 false Vehicle Speed 1.385,1.51 2.208,1.75 0.823,0.24 10 false Input Speed 2.406,0.802 2.771,1.375 0.365,0.573 10 false Extra Low Gear 0.708,3.156 2.063,3.417 1.354,0.26 10 false Synchronizer on Area



e.

Acceleration Improvement Control (Intermediate to high accelerator opening angle)

i.

In pursuit of an acceleration feeling that more closely matches the sensibilities of the driver, CVT control has been revised and engine-integrated control has been further evolved.

X140539E02
2.594,1.25 3.115,0.219 3.115,0.219 3.281,0.219 true 2.146,0.458 2.521,0.99 0.375,0.531 10 false Extra Low Gear 1.146,1.698 1.958,1.979 0.813,0.281 10 false Input Speed 4.479,1.802 6.156,2.073 1.677,0.271 10 false Pulley Ratio (High) 2.948,3.073 4.625,3.344 1.677,0.271 10 false Vehicle Speed 4.708,1.208 6.385,1.479 1.677,0.271 10 false High Acceleration Area 3.344,0.135 4.5,0.396 1.156,0.26 10 false Gear/ Belt Shift 3.135,0.531 4.813,0.802 1.677,0.271 10 false Pulley Ratio (Low)


ii.

When starting off, gear mode provides acceleration matched with a linear increase in engine RPM. Even after changeover from gear mode to belt mode, the vehicle speed increase is accompanied by a similar linear engine RPM increase and rhythmical shifting.


iii.

Also, while driving the vehicle speed and changes in the accelerator opening angle are used to determine the driver's desired acceleration, allowing the driver's initial accelerator pedal movements to receive the desired response. Subsequently, optimized shifting speeds enable natural RPM increase to achieve a linear acceleration feel.

X140540E01
3.427,0.635 5.438,0.917 2.01,0.281 10 false Gear/ Belt Shift 4.146,1.344 4.604,1.583 0.458,0.24 10 false Belt 2.594,1.354 3.052,1.594 0.458,0.24 10 false Gear 0.625,1.417 1.76,1.865 1.135,0.448 10 false Accelerator Pedal Position 0.865,3.375 1.823,3.604 0.958,0.229 10 false Engine Speed 0.927,5.281 1.865,5.531 0.938,0.25 10 false Acceleration 3.646,2.885 6.969,3.115 3.323,0.229 10 false Increases Linearly in Accordance with Vehicle Speed 2.917,3.583 5.198,3.823 2.281,0.24 10 true Improved Acceleration Feeling 2.698,5.417 6.948,5.615 4.25,0.198 10 false Linearly Increases Acceleration Immediately Following Acceleration 5.26,5.76 5.708,6.021 0.448,0.26 10 false Time



f.

Deceleration Improvement Control

i.

During deceleration, a pulley ratio which allows high engine speed to be maintained, is calculated, thus ensuring adequate engine braking.


ii.

During subsequent acceleration, the engine is controlled to generate driving force quickly.

X104369E08
3.073,0.396 2.802,0.396 2.802,0.396 2.802,1.021 false 4.469,1.49 5.396,1.49 false 0.458,2.865 1.604,3.635 1.146,0.771 10 false Accelerator Pedal Operation 0.875,1.281 2.021,1.677 1.146,0.396 10 false Engine Speed 1.625,2.76 1.99,3.156 0.365,0.396 10 false On 1.625,3.281 1.99,3.677 0.365,0.396 10 false Off 4.76,3.438 5.323,3.781 0.563,0.344 10 false Time 3.135,0.323 5.563,1.094 2.427,0.771 10 false Ensures Engine Braking by Maintaining High Engine Speed 5.469,1.396 7.01,2.25 1.542,0.854 10 false Improves Re-acceleration Response through Quick Engine Speed Increase


iii.

Furthermore, to prepare for the changeover to gear mode in order to accelerate again after decelerating, it is necessary to re-engage the synchro that is released at high speeds, but sensing the driver's control inputs and the vehicle behavior when driving allows vehicle behavior when re-engaging to be controlled.

X140541E06
2.146,3.344 2.333,3.344 2.333,3.344 2.677,2.885 true 3.177,3.073 5.167,3.271 1.99,0.198 10 false Vehicle Speed 1.313,1.656 2.188,1.885 0.875,0.229 10 false Input Speed 2.427,0.792 2.833,1.396 0.406,0.604 10 false Extra Low Gear 3.385,0.667 4.76,0.885 1.375,0.219 10 false Pulley Ratio (Low) 4.698,1.865 6.073,2.083 1.375,0.219 10 false Pulley Ratio (High) 4.042,2.448 5.99,2.667 1.948,0.219 10 false High Fuel Economy Area 0.76,3.25 2.26,3.625 1.5,0.375 10 false Synchronizer on Area



g.

10-speed Sport Sequential Shiftmatic

i.

The driver can select the desired shift range by moving the shift lever to "+" (forward) or to "-" (backward) while the shift lever is in M (10-speed sport sequential shiftmatic mode). Thus, the driver is able to change shift range with a manual-like feel.

X143838E03
0.604,0.719 1.063,1.073 0.458,0.354 10 false ECM 1.927,0.448 2.771,1.135 0.844,0.688 10 false Transmission Control ECU 3.417,0.313 4.594,0.708 1.177,0.396 10 false M Position Signal 3.302,0.781 4.76,1.177 1.458,0.396 10 false Shift Range Up Signal 3.26,1.302 4.875,1.781 1.615,0.479 10 false Shift Range Down Signal 5.51,0.135 6.708,0.75 1.198,0.615 10 false Transmission Floor Shift Assembly 5.479,0.948 6.802,1.656 1.323,0.708 10 false Transmission Control Switch 2.073,3.854 2.906,4.313 0.833,0.458 10 false Transaxle 0.625,3.542 1.177,4.01 0.552,0.469 10 false Engine 0.573,4.365 2.365,4.719 1.792,0.354 10 false : CAN Communication Line 1.469,1.958 2.229,2.552 0.76,0.594 10 false Pulley Ratio Control 2.5,1.948 3.438,2.552 0.938,0.604 10 false Fluid Pressure Control 0.927,1.792 1.302,2.25 0.375,0.458 10 false ESA 0.135,1.792 0.625,2.219 0.49,0.427 10 false ETCS-i


ii.

10-speed sport sequential shiftmatic mode can be selected from normal driving mode by moving the shift lever to M. The driver can change the gear step by selecting it using the shift lever and engine braking force is provided in accordance with the selected gear step.


iii.

Through cooperative control with the Electronic Spark Advance (ESA) and Electronic Throttle Control System-intelligent (ETCS-i), in NORMAL mode, the engine torque is finely controlled during shifting to enhance shift response and reduce shift shock, realizing shifting with smooth and sharp response.


iv.

The shift position and shift range indicator is provided in the multi-information display of the combination meter assembly. When the shift lever is in P, R, N or D, the shift position is indicated in the shift position and shift range indicator. When the shift lever is in M, "M" and the selected shift range is displayed in the shift position and shift range indicator.

X143839C02
3.958,2.302 4.083,2.479 4.083,2.479 4.24,2.479 true 1.406,0.313 1.719,0.469 0.313,0.156 10 false *a 2.583,1.604 2.896,1.76 0.313,0.156 10 false *b 4.281,2.375 4.594,2.531 0.313,0.156 10 false *c
*a When shift lever is in P, R, N or D *b When shift lever is in M
*c Shift Range Indicator - -



v.

In 10-speed sport sequential shiftmatic mode, the transmission automatically upshifts or downshifts under the following conditions:

Condition System Control
Engine is under-revving. 1 step downshift
Engine is over-revving. 1 step upshift


vi.

When the vehicle is stopped during 10-speed sport sequential shiftmatic mode, the transmission automatically downshifts to M1.


vii.

When there is a system malfunction or abnormality, or when a requested shift operation is judged to be impossible, operation of the 10-speed sport sequential shiftmatic mode is restricted. In this case, the buzzer in the combination meter will sound to alert the driver.


viii.

If the vehicle speed or engine speed exceeds or goes below a preset level in response to the driver's downshift operation request, changing the shift range will be prohibited. In this case, the buzzer in the combination meter will sound to alert the driver.



h.

Uphill/Downhill Shift Control

i.

Uphill/downhill shift control helps perform optimal shifting while driving on a winding uphill or downhill road.


ii.

When the transmission control ECU determines the vehicle is traveling uphill, the control restricts upshifting, thus offering smooth driving.


iii.

When on a downhill, if a vehicle accelerates is detected, a downshift is automatically implemented. In addition if any braking operation is detected, a more downshift is automatically implemented. By these a engine brake force is changed progressively which contributes to reducing driver operations.

X148468E01
0.167,2.469 1.208,2.75 1.042,0.281 10 false without Control 0.313,3.052 1.208,3.313 0.896,0.26 10 false with Control 2.313,2.021 2.885,2.448 0.573,0.427 10 false Down shift 4.698,2.75 5.406,3.167 0.708,0.417 10 false Downshift 2.948,2.01 3.375,2.406 0.427,0.396 10 false Up shift 4.781,2.115 5.479,2.479 0.698,0.365 10 false Upshift 3.979,2.771 4.49,3.073 0.51,0.302 10 false Upshift 2.531,2.781 3.646,3.125 1.115,0.344 10 false Restricts Upshift 1.479,2.208 2.021,2.49 0.542,0.281 10 false Crusing 5.958,2.125 6.5,2.406 0.542,0.281 10 false Crusing 5.948,2.729 6.5,3.125 0.552,0.396 10 false Crusing 1.458,2.792 2,3.073 0.542,0.281 10 false Crusing 3.5,1.99 3.875,2.552 0.375,0.563 10 false Down shift 4.073,1.979 4.448,2.49 0.375,0.51 10 false Up shift


iv.

The actual acceleration calculated from the vehicle speed signal is compared with the reference acceleration (based on level road travel) stored in the transmission control ECU to determine uphill or downhill travel.

X109760C02
1.219,0.521 1.01,0.521 1.01,0.521 0.75,0.99 true 5.125,0.813 4.917,0.813 4.917,0.813 4.656,1.292 true 1.26,0.458 1.552,0.656 0.292,0.198 10 *c 5.156,0.729 5.448,0.927 0.292,0.198 10 *d 0.271,0.271 0.563,0.469 0.292,0.198 10 *a 3.865,0.292 4.156,0.49 0.292,0.198 10 *b
*a Uphill *b Downhill
*c Smaller *d Greater
V100135

Reference Acceleration
V100136

Actual Acceleration




i.

Flex Lock-up Control

i.

In order to improve the transmission efficiency and also the fuel economy, the linear solenoid valve SLU for lock-up engagement pressure control is employed to deliver flex lock-up control that can provide more precise control than that of a conventional lock-up clutch mechanism.


ii.

The flex lock-up control consists of flex start control and flex lock-up control during deceleration.


iii.

The flex start control aggressively operates the lock-up clutch during start-off to increase the transmission efficiency, as a result, the engine can run in its most efficient operating range.

X105133E04
3.813,1.281 4.01,0.854 4.01,0.854 4.125,0.854 true 1.219,1.125 2.167,1.406 0.948,0.281 10 false Engine Speed 3.271,2.292 3.635,2.583 0.365,0.292 10 false Time 4.063,1.885 4.99,2.177 0.927,0.292 10 false Vehicle Speed 2.573,0.625 3.74,0.938 1.167,0.313 10 false Conventional CVT 4.208,0.792 6.75,1.146 2.542,0.354 10 false Decreases engine speed at vehicle start


iv.

Flex lock-up control during deceleration is used to expand the fuel-cut range. It operates the lock-up clutch over the low vehicle speed range when the vehicle decelerates so that minimal speed difference between the engine speed and turbine speed can be maintained.



j.

Clutch Capacity Control

i.

When driving in belt mode, and sudden braking causes excessive input forces from the road surface, the C2 clutch performs torque capacity control to protect the belt by limiting the load applied to it. The hydraulic pressure pressing on the belt is reduced to match the torque capacity of the C2 clutch, and the reduced load on the oil pump contributes to fuel economy improvements.

X140542E02
2.031,2.521 2.188,2.521 2.188,2.521 2.438,2 true 0.479,2.438 2.052,2.927 1.573,0.49 10 false Slipping of the C2 Clutch Protects the Belt




FAIL-SAFE


a.

This function minimizes the loss of operability when a malfunction occurs in any sensor or shift solenoid valve.


b.

For details, refer to the Repair Manual.



DIAGNOSIS


a.

When the transmission control ECU detects a malfunction, it records the malfunction and information related to the fault. Furthermore, the transmission control ECU will illuminate the Malfunction Indicator Lamp (MIL) in the combination meter to inform the driver.


b.

At the same time, the Diagnostic Trouble Codes (DTCs) are stored in memory. The DTCs can be read by connecting the Global TechStream (GTS) to the DLC3. For details, refer to the Repair Manual.