Home › Engine / Hybrid System › 2AR-FE (ENGINE CONTROL) › MASS AIR FLOW METER › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065323 2AR-FE ENGINE CONTROL _0319009 MASS AIR FLOW METER G

2AR-FE ENGINE CONTROL  MASS AIR FLOW METER  INSPECTION  


PROCEDURE

Hide 22204 1.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY

a.
A190679C20
0.927,2.042 1.354,0.719 1.354,0.719 1.74,0.719 true 1.792,3.094 1.385,3.094 1.385,3.094 1.021,2.531 true 1.802,0.625 2.125,0.854 0.323,0.229 10 false *a 1.885,3.01 2.219,3.208 0.333,0.198 10 false *b
*a Platinum Hot Wire (Heater)
*b Temperature Sensor (Thermistor)


Perform a visual check for any foreign matter on the platinum hot wire (heater) and temperature sensor (thermistor) of the mass air flow meter sub-assembly shown in the illustration.

OK:

There is no foreign matter.


If the result is not as specified, clean the mass air flow meter sub-assembly.


b.
A487339C01
1.677,2.833 1.344,2.833 true 1.563,0.823 1.229,0.823 true 1.177,2.76 1.49,2.917 0.313,0.156 10 false *a 2.073,4.333 2.385,4.49 0.313,0.156 10 false *b 1.594,0.74 1.906,0.896 0.313,0.156 10 false *c
*a Air Blow Gun
*b 10 mm (0.394 in.)
*c Airflow Hole


Clean the mass air flow meter sub-assembly.

NOTICE:
·

Do not contact the mass air flow meter sub-assembly with the nozzle of the air blow gun.

·

Do not insert the nozzle of the air blow gun into the airflow hole.



i.
A398469C01
0.125,0.125 0.365,0.302 0.24,0.177 10 false *a 1.313,0.24 1.552,0.406 0.24,0.167 10 false *b 1.563,0.573 1.792,0.74 0.229,0.167 10 false *c 0.688,0.906 0.927,1.083 0.24,0.177 10 false *d 0.677,1.708 0.917,1.885 0.24,0.177 10 false *e
*a Air Blow Duration
*b 3 to 6 Seconds
*c 1 Second
*d Air Blowing
*e Air Stopped


Using an air blow gun, clean the hole of the mass air flow meter sub-assembly by applying approximately 10 intermittent bursts of air to the airflow hole at a pressure of approximately 392 to 981 kPa (4.0 to 10.0 kgf/cm2, 57 to 142 psi).

HINT:

After performing cleaning, read the value of Data List item "MAF" using the GTS and if the value is not as specified, replace the mass air flow meter sub-assembly.




c.
A167890C01
1.542,0.771 1.688,0.771 1.688,0.771 1.854,1.448 true 2.052,1.521 2.552,1.521 true 1.344,1.448 1.448,1.594 0.104,0.146 10 5 1.5,1.448 1.604,1.594 0.104,0.146 10 4 1.656,1.448 1.76,1.594 0.104,0.146 10 3 1.958,1.448 2.063,1.594 0.104,0.146 10 1 1.802,1.448 1.906,1.594 0.104,0.146 10 2 2.583,1.448 3,1.646 0.417,0.198 10 THA 1.333,0.698 1.594,0.875 0.26,0.177 10 E2 0.063,0.052 0.24,0.219 0.177,0.167 10 *a
*a Component without harness connected
(Mass Air Flow Meter Sub-assembly)


Check the intake air temperature sensor (thermistor) resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (THA) - 2 (E2) Always 0.47 to 19.3 kΩ


If the result is not as specified, replace the intake mass air flow meter sub-assembly.