Home › Engine / Hybrid System › 2GR-FKS (FUEL) › FUEL INJECTOR (for Port Injection)
RM33A0E _51 Engine / Hybrid System _065334 2GR-FKS FUEL _0319414 FUEL INJECTOR(for Port Injection) G

2GR-FKS FUEL  FUEL INJECTOR(for Port Injection)  INSPECTION  


PROCEDURE

Hide 23250 1.INSPECT FUEL INJECTOR ASSEMBLY

a.

Check the resistance.

i.
A333794C01
0.219,0.146 0.531,0.302 0.313,0.156 10 false *a
*a Component without harness connected
(Fuel Injector Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 11.6 to 12.4 Ω


If the result is not as specified, replace the fuel injector assembly.



b.

Check the operation.

CAUTION:

Perform the inspection in a well-ventilated area.

Do not perform the inspection near an open flame.


i.
A405952

Disengage the 2 claws to remove the No. 2 fuel pipe clamp.


ii.
A393279

Remove the No. 1 fuel pipe clamp from the fuel tube connector.


iii.
A405954

Disconnect the fuel tube sub-assembly.

Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


iv.
A264971C19
0.5,1.656 0.729,1.885 0.729,1.885 0.833,1.885 false 0.854,0.906 1.146,0.615 1.146,0.615 1.26,0.615 false 1.99,1.292 2.292,1.594 2.292,1.594 2.417,1.594 false 2.646,0.698 2.948,0.396 2.948,0.396 3.063,0.396 false 0.875,1.802 1.156,2.042 0.281,0.24 10 false *a 1.333,0.521 1.656,0.781 0.323,0.26 10 false *b 2.479,1.51 2.802,1.76 0.323,0.25 10 false *c 3.135,0.292 3.354,0.542 0.219,0.25 10 false *d
*a SST (Hose)
*b SST (Hose Band)
*c SST (Fuel Tube Connector)
*d Fuel Pipe (Vehicle Side)


Connect SST (fuel tube connector) to SST (hose) with SST (hose band), and then connect them to the fuel pipe (vehicle side).

SST
09268-31015  (09268-41500, 09268-41700, 95336-08070)

NOTICE:

Make sure the SST (fuel tube connector) O-rings are not damaged and are free of foreign matter as they are used to seal the connections between the fuel tube connector and fuel pipe.



v.

Apply a light coat of gasoline to a new O-ring, and then install the O-ring to the fuel injector assembly.


vi.
A333797C03
1.281,0.135 1.563,0.135 false 1.906,0.292 2.188,0.292 false 1.26,0.813 1.542,0.813 false 2.563,1.146 2.844,1.146 false 1.135,1.24 1.573,1.24 false 1.281,2.052 1.563,2.052 false 0.958,1.167 1.271,1.323 0.313,0.156 10 false *1 1.083,0.729 1.396,0.885 0.313,0.156 10 false *a 2.25,0.219 2.563,0.375 0.313,0.156 10 false *b 2.896,1.063 3.208,1.219 0.313,0.156 10 false *c 1.115,0.063 1.427,0.219 0.313,0.156 10 false *d 1.104,1.969 1.417,2.125 0.313,0.156 10 false *e
*1 O-ring
*a SST (Adapter)
*b SST (Hose Band)
*c SST (Clamp)
*d SST (Hose)
*e Vinyl Tube


Connect SST (adapter) and SST (hose) to the fuel injector assembly, and hold the fuel injector assembly and union with SST (clamp).

SST
09268-31015  (09268-41600, 09268-41300, 09268-41700, 95336-08070)


vii.
A333798C01
1.427,1.615 1.667,2.052 1.667,2.052 1.813,2.052 false 1.583,1.323 2.198,1.75 2.198,1.75 2.417,1.75 true 2.469,1.656 2.781,1.813 0.313,0.156 10 false *a 1.865,1.969 2.188,2.167 0.323,0.198 10 false *b
*a Lock
*b SST (Tie Band)


Tie SST (clamp) and SST (adapter) together with SST (tie band) as shown in the illustration.

SST
09268-31015  (09268-41800)

NOTICE:
·

As SST (tie band) does not completely prevent SST (clamp) from becoming loose, do not subject the parts to any impacts while using them.

·

Before using SST (tie band), make sure that there is no wear, damage or cracks. If there are any abnormalities, replace SST.



HINT:

When removing SST (tie band), disengage the lock.



viii.

Check that SST (clamp) and SST (adapter) cannot be easily separated.


ix.

Install a vinyl tube to the fuel injector assembly.

CAUTION:

Install a suitable vinyl tube to the fuel injector assembly to prevent fuel from spraying.



x.

Set the fuel injector assembly into a graduated cylinder.


xi.

Connect the GTS to the DLC3.


xii.

Turn the engine switch on (IG).

NOTICE:

Do not start the engine.



xiii.

Turn the GTS on.


xiv.

Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay.

Powertrain > Engine > Active Test
Tester Display
Activate the Circuit Relay
50004 372 40

xv.
A333799C01
2.073,0.885 2.073,0.427 false 2,0.917 2.313,1.073 0.313,0.156 10 false *a
*a SST (EFI Inspection Wire I)


Connect SST (EFI inspection wire I) to the fuel injector assembly and battery for 15 seconds, and measure the injection volume with the graduated cylinder. Test each fuel injector assembly 2 or 3 times.

SST
09842-30090  

Standard Injection Volume:
Tester Connection Condition Specified Condition
Positive (+) battery terminal - Negative (-) battery terminal Per 15 seconds 67 to 81 cc (4.1 to 4.9 cu. in.)


Difference between Each Fuel Injector Assembly:

14 cc (0.9 cu. in.) or less


NOTICE:
·

Make sure that SST (EFI inspection wire I) is securely connected.

·

Always switch the voltage on and off at the battery side, not the fuel injector assembly side.



If the injection volume is not as specified, replace the fuel injector assembly.



c.

Check for leaks.

i.

Disconnect SST (EFI inspection wire I) from the battery and check for fuel leaks from the fuel injector assembly.

Standard Fuel Drop:

1 drop or less per 20 minutes


If the result is not as specified, replace the fuel injector assembly.


ii.

Connect the fuel tube sub-assembly.

Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


iii.

Install the No. 1 fuel pipe clamp to the fuel tube connector.


iv.

Engage the 2 claws to install the No. 2 fuel pipe clamp.