Home › Engine / Hybrid System › 2GR-FKS (FUEL) › FUEL PRESSURE SENSOR (for High Pressure)
RM33A0E _51 Engine / Hybrid System _065334 2GR-FKS FUEL _0319419 FUEL PRESSURE SENSOR(for High Pressure) A

2GR-FKS FUEL  FUEL PRESSURE SENSOR(for High Pressure)  INSTALLATION  


PROCEDURE

Hide 23809K 1.INSTALL FUEL PIPE PLUG SUB-ASSEMBLY

a.

Install a new O-ring, No. 1 fuel injector back-up ring, No. 2 fuel injector back-up ring and No. 3 fuel injector back-up ring to the fuel pipe plug sub-assembly as shown in the illustration.

A363213C02
5.385,2.865 5.51,2.865 5.51,2.865 5.646,3.115 false 5.063,0.719 5.177,0.719 5.177,0.719 5.177,1.01 false 4.948,2.021 4.948,1.677 false 5.375,1.063 5.552,0.792 5.552,0.792 5.667,0.792 false 5.469,1.594 5.615,1.813 5.615,1.813 5.729,1.813 false 5.865,2.823 5.979,2.823 5.979,2.823 6.052,3.021 false 6.406,3.51 6.406,3.365 false 6.552,3.281 6.552,2.917 6.552,2.917 6.646,2.917 false 4.052,0.365 4.323,0.365 false 3.875,0.302 4.188,0.458 0.313,0.156 10 false *1 4.854,2.052 5.167,2.208 0.313,0.156 10 false *2 5.719,0.729 6.031,0.885 0.313,0.156 10 false *3 5.792,1.75 6.104,1.906 0.313,0.156 10 false *4 4.875,0.656 5.188,0.813 0.313,0.156 10 false *5 1.844,1.125 2.156,1.281 0.313,0.156 10 false *a 1.042,2.417 1.354,2.573 0.313,0.156 10 false *b 2.823,2.406 3.135,2.563 0.313,0.156 10 false *c 1.885,1.667 2.198,1.823 0.313,0.156 10 false *d 1.052,1.677 1.365,1.833 0.313,0.156 10 false *e 5.198,2.802 5.51,2.958 0.313,0.156 10 false *2 5.677,2.76 5.99,2.917 0.313,0.156 10 false *5 6.313,3.542 6.625,3.698 0.313,0.156 10 false *3 6.698,2.854 7.01,3.01 0.313,0.156 10 false *4 2.823,1.698 3.135,1.854 0.313,0.156 10 false *e
*1 Fuel Pipe Plug Sub-assembly *2 No. 1 Fuel Injector Back-up Ring
*3 No. 2 Fuel Injector Back-up Ring *4 No. 3 Fuel Injector Back-up Ring
*5 O-ring - -
*a Opening *b Overlapped
*c Stretched *d Correct
*e Incorrect - -


NOTICE:
·

Check that there is no foreign matter or damage on the O-ring groove of the fuel pipe plug sub-assembly.

·

Check that the No. 1 fuel injector back-up ring and No. 3 fuel injector back-up ring are installed in the correct orientation.

·

Make sure that the No. 1 fuel injector back-up ring, No. 2 fuel injector back-up ring, No. 3 fuel injector back-up ring and O-ring are installed in the correct order.

·

Check that the opening of the No. 1 fuel injector back-up ring is not overlapped or stretched as shown in the illustration.

·

After installing the O-ring, check that it is not contaminated with foreign matter and is not damaged.




b.

w/ Dust Cap:

i.

Install the dust cap sub-assembly to the fuel pipe plug sub-assembly.



c.
A363215

Install a new gasket to the fuel pipe plug sub-assembly as shown in the illustration.


d.

Secure the fuel delivery pipe with sensor assembly LH in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



e.

Using a 5 mm hexagon socket wrench, install the fuel pipe plug sub-assembly to the fuel delivery pipe with sensor assembly LH with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


f.

Remove the fuel delivery pipe with sensor assembly LH from the vise.


Hide 23860 2.INSTALL FUEL PRESSURE SENSOR (FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY LH)

HINT:

Perform "Inspection After Repair" after replacing the fuel pressure sensor (fuel delivery pipe with sensor assembly LH).

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL INJECTOR (for Direct Injection)>INSTALLATION

NOTICE:
·

Do not remove the fuel pressure sensor from the fuel delivery pipe with sensor assembly LH.

·

If the fuel pressure sensor is removed, replace the fuel pressure sensor (fuel delivery pipe with sensor assembly LH) with a new one.



Hide 3.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the fuel pressure sensor (fuel delivery pipe with sensor assembly LH).

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION