This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
1.INSTALL CAMSHAFT
Perform inspection after repair after replacing the camshaft, No. 2 camshaft, camshaft timing gear assembly and camshaft timing exhaust gear assembly.
Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION
| *a | "0" Timing Mark |
| *b | Timing Mark |
Turn the crankshaft clockwise to align the timing mark (cutout) on the crankshaft pulley assembly with the "0" timing mark on the No. 2 timing gear cover assembly.
| *1 | No. 1 Valve Rocker Arm Sub-assembly |
| *2 | Valve Lash Adjuster Assembly |
| *3 | Valve Stem Cap |
Check that the No. 1 valve rocker arm sub-assembly is correctly installed as shown in the illustration.
Clean the camshaft housing sub-assembly and the cams and journals of the camshaft and No. 2 camshaft, and then apply engine oil to them.
Apply a light coat of engine oil to the journals of the camshaft and install the camshaft to the camshaft housing sub-assembly.
Apply a light coat of engine oil to the journals of the No. 2 camshaft and install the No. 2 camshaft to the camshaft housing sub-assembly.
| *1 | No. 1 Camshaft Bearing Cap |
| *2 | No. 2 Camshaft Bearing Cap |
| *3 | No. 3 Camshaft Bearing Cap |
| *4 | No. 4 Camshaft Bearing Cap |
Set the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, 2 No. 3 camshaft bearing caps and No. 4 camshaft bearing cap as shown in the illustration.
Uniformly tighten the 14 bolts in the order shown in the illustration.
Uniformly tighten the 8 bolts in the order shown in the illustration.
Set the camshaft timing gear assembly and camshaft timing exhaust gear assembly to the chain sub-assembly as shown in the illustration.
| *a | Paint Mark |
| *b | Timing Mark |
Align the timing mark on the camshaft timing gear assembly with the paint mark on the chain sub-assembly.
| *a | Paint Mark |
| *b | Timing Mark |
Align the timing mark on the camshaft timing exhaust gear assembly with the paint mark on the chain sub-assembly.
| *a | Knock Pin |
Using the hexagonal portion of the camshaft, install the camshaft timing gear assembly to the camshaft.
Check that the knock pin matches the pin hole from the No. 2 timing gear cover sub-assembly side.
Using a 10 mm bi-hexagon socket wrench, temporarily install the camshaft timing gear assembly with the bolt.
Temporarily install the bolt enough that the camshaft timing gear assembly does not detach from the knock pin of the camshaft.
Type A:
Using the hexagonal portion of the No. 2 camshaft, install the camshaft timing exhaust gear assembly to the No. 2 camshaft.
Temporarily install the 2 bolts.
The 2 bolts can only be installed as shown in the illustration if the knock pin on the No. 2 camshaft and the pin hole on the camshaft timing exhaust gear assembly match. If the 2 bolts cannot be installed, the knock pin and pin hole do not match.
Type B:
Using the hexagonal portion of the No. 2 camshaft, install the camshaft timing exhaust gear assembly to the No. 2 camshaft.
Temporarily install the 2 bolts.
The 2 bolts can only be installed as shown in the illustration if the knock pin on the No. 2 camshaft and the pin hole on the camshaft timing exhaust gear assembly match. If the 2 bolts cannot be installed, the knock pin and pin hole do not match.
| *1 | No. 1 Chain Vibration Damper |
Check the status of the camshaft timing gear assembly and camshaft timing exhaust gear assembly temporarily installed to each camshaft.
Camshaft timing gear assembly side:
Check that the chain sub-assembly does not overlap the No. 1 chain vibration damper as shown in the illustration.
If the chain sub-assembly overlaps the No. 1 chain vibration damper, install it again.
| *1 | Chain Tensioner Slipper |
Camshaft timing exhaust gear assembly side:
Check that the chain sub-assembly does not overlap the chain tensioner slipper as shown in the illustration.
If the chain sub-assembly overlaps the chain tensioner slipper, install it again.
| *a | Hold |
Using the hexagonal portion of the camshaft, hold the camshaft.
Do not damage the camshaft housing sub-assembly, cylinder head sub-assembly and spark plug tube.
Do not disassemble the camshaft timing gear assembly.
Using a 10 mm bi-hexagon socket wrench, tighten the bolt on the camshaft timing gear assembly.
Type A:
| *a | Hold |
Using the hexagonal portion of the No. 2 camshaft, hold the No. 2 camshaft.
Do not damage the camshaft housing sub-assembly, cylinder head sub-assembly and spark plug tube.
Using a 5 mm hexagon wrench, tighten the 2 bolts.
Type B:
| *a | Hold |
Using the hexagonal portion of the No. 2 camshaft, hold the No. 2 camshaft.
Do not damage the camshaft housing sub-assembly, cylinder head sub-assembly and spark plug tube.
Using a 5 mm hexagon wrench, tighten the 2 bolts.
| *a | Paint Mark |
| *b | Timing Mark |
Check that the paint marks and timing marks are positioned as shown in the illustration.
Using the hexagonal portion of the camshaft, check that the chain sub-assembly slackens when the camshaft is moved in the direction shown in the illustration.
| *a | Hold | - | - |
|
Turn | - | - |
If the chain sub-assembly remains tight and does not slacken, the chain tensioner slipper and No. 1 chain vibration damper may overlap the chain sub-assembly, so install them again.
Remove the pin from the No. 1 chain tensioner assembly.
2.INSTALL STRAIGHT SCREW PLUG
3.SET NO. 1 CYLINDER TO TDC (COMPRESSION)
23477
4.INSTALL FUEL PUMP LIFTER GUIDE
11193
5.INSTALL SPARK PLUG TUBE GASKET
11201
6.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
29300
7.INSTALL VACUUM PUMP ASSEMBLY
13090E
8.INSTALL CAM TIMING CONTROL MOTOR O-RING
13090D
9.INSTALL CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY
135A0A
10.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY)
15370
11.INSTALL CAM TIMING OIL CONTROL SOLENOID ASSEMBLY
12602C
12.INSTALL NO. 2 ENGINE COVER
47381J
13.INSTALL NO. 2 BRAKE TUBE CLAMP BRACKET
19500
14.INSTALL IGNITION COIL ASSEMBLY
82121
15.CONNECT ENGINE WIRE
Engage the 3 clamps to connect the engine wire.
Engage the 6 connectors.
88710E
16.CONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY
Engage the 2 clamps to connect the air conditioning tube and accessory assembly.
23100X
17.INSTALL FUEL PUMP ASSEMBLY (for High Pressure)