Home › Engine / Hybrid System › A25A-FKS (COOLING) › FLOW SHUTTING VALVE (for Heater) › 2017.09–2017.12
RM33A0E _51 Engine / Hybrid System _065346 A25A-FKS COOLING _0319574 FLOW SHUTTING VALVE(for Heater) A

A25A-FKS COOLING  FLOW SHUTTING VALVE(for Heater)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during flow shutting valve (water by-pass hose assembly) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When the ECM is replaced with a new one, reset memory is unnecessary.

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)for UB80E Initialization
(Click here)for UB80E Registration
Replacement of ECM
(If impossible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.

PROCEDURE

Hide 16261G 1.REMOVE FLOW SHUTTING VALVE (NO. 1 WATER BY-PASS HOSE)

Hide 16260 2.REMOVE FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)

a.
A402652

Disengage the clamp to disconnect the vacuum hose from the engine wire harness.


b.
A402653

Disconnect the 3 connectors.


c.

Disengage the clamp to disconnect the engine wire harness from the water hose clamp bracket.


d.

Disconnect the outlet heater hose connector from the No. 2 water by-pass pipe sub-assembly.

NOTICE:

Remove any foreign matter on the No. 2 water by-pass pipe sub-assembly and outlet heater hose connector before performing this work.


i.
A402655C01
1.802,1.177 2.021,1.417 2.021,1.417 2.208,1.417 false 2.26,1.333 2.5,1.542 0.24,0.208 10 true *a
*a Retainer
V100135

Pull out
V100136

Pull off


Pull out the retainer to disengage the lock claws and pull off the outlet heater hose connector.


ii.

Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.


iii.

Cover the disconnected No. 2 water by-pass pipe sub-assembly and outlet heater hose connector with plastic bags to prevent damage and contamination.



e.

Disconnect the inlet heater hose connector from the flow shutting valve (water by-pass hose assembly).

NOTICE:

Remove any foreign matter on the flow shutting valve (water by-pass hose assembly) and inlet heater hose connector before performing this work.


i.
A402656C01
1.396,1.104 1.729,0.542 1.729,0.542 1.958,0.542 false 2.01,0.458 2.271,0.667 0.26,0.208 10 true *a
*a Retainer
V100135

Pull out
V100136

Pull off


Pull out the retainer to disengage the lock claws and pull off the inlet heater hose connector.


ii.

Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.


iii.

Cover the disconnected inlet heater hose connector with plastic bag to prevent damage and contamination.



f.
A402658

Remove the bolt to disconnect the No. 2 water by-pass pipe sub-assembly.


g.
A402659

Remove the bolt to disconnect the flow shutting valve (water by-pass hose assembly).


h.
A402660

Disengage the 2 clamps to disconnect the wire harness.


i.
A402661

Remove the 2 bolts and the water hose clamp bracket.


j.
A402664

Slide the clip and disconnect the flow shutting valve (water by-pass hose assembly) from the water by-pass outlet sub-assembly.

HINT:

Use a container to catch any engine coolant which flows out of the flow shutting valve (water by-pass hose assembly) and water by-pass outlet sub-assembly.



k.
A402662

Slide the clip and disconnect the flow shutting valve (water by-pass hose assembly) from the transmission oil cooler.

HINT:

Use a container to catch any engine coolant which flows out of the flow shutting valve (water by-pass hose assembly) and transmission oil cooler.