Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column) › 2017.09–2017.12
RM33A0E _55 Steering _065371 STEERING COLUMN _0319591 STEERING COLUMN ASSEMBLY(for Manual Tilt and Manual Telescopic Steering Column) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for Manual Tilt and Manual Telescopic Steering Column)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during steering column assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: w/ Smart Entry and Start System

Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Steering sensor
·

Steering angle neutral point (Initialize parking assist monitor system)

·

Steering angle setting


Parking assist monitor system for Initialization:(Click here)
for Calibration:(Click here)
Steering lock ECU (steering lock actuator or upper bracket assembly)*1 Perform code registration (Immobiliser function)
·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.

PROCEDURE

Hide 2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45130 3.REMOVE HORN BUTTON ASSEMBLY

Hide 4.REMOVE STEERING WHEEL ASSEMBLY

Hide 45024 5.REMOVE LOWER STEERING COLUMN COVER SUB-ASSEMBLY

NOTICE:

Removing the lower steering column cover sub-assembly in the incorrect order will cause the parts to break.


a.

Release the tilt and telescopic lever and fully extend and lower the steering column assembly.


b.

Lock the tilt and telescopic lever.


c.
C384438

Remove the 3 screws.


d.
C384439C01
0,0 0,0 false
V100155

Push Area
V113147

Push in this Direction


While pressing the push area shown in the illustration to disengage the 2 claws, slightly lower the lower steering column cover sub-assembly.


Hide 45286B 6.REMOVE UPPER STEERING COLUMN COVER

a.
C373449C01
0,0 0,0 false
V113147

Separate in this direction


Disengage the claw and separate the upper steering column cover.


b.
C373450

Disengage the 2 claws and 4 clips to remove the upper steering column cover.


Hide 89782 7.REMOVE TRANSPONDER KEY COIL (w/o Entry and Start System)

a.
C373458

Disconnect the connector.


b.

Disengage the 2 claws and remove the transponder key coil.


Hide 8.REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not remove/install the spiral cable with sensor sub-assembly with the battery connected and the ignition switch ON.

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the ignition switch ON.

·

Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.



a.

Disconnect each connector from the turn signal switch assembly with spiral cable sub-assembly.


b.
C373451C01
1.698,0.521 1.99,0.521 false 2.031,0.427 2.344,0.583 0.313,0.156 10 false *a
*a Clamp


Using pliers, expand the clamp.


c.

While holding the clamp expanded, raise the claw using a screwdriver to disengage it, and then remove the turn signal switch assembly with spiral cable sub-assembly from the steering column assembly.


Hide 73900 9.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 87211 10.REMOVE NO. 1 AIR DUCT (for LHD)

a.
C378964C01
1.427,0.167 1.74,0.323 0.313,0.156 10 false *a 1.615,2.604 1.76,2.781 0.146,0.177 10 true A
*a View A
V100137

Front


Remove the 2 bolts.


b.

Disengage the 3 claws to remove the No. 1 air duct.

NOTICE:

Be careful not to deform or damage the lower heater case of the air conditioner unit assembly when removing the No. 1 air duct.



Hide 87211 11.REMOVE NO. 1 AIR DUCT (for RHD)

a.
C379827C02
1.76,0.271 2.073,0.427 0.313,0.156 10 false *a 1.771,2.635 1.917,2.771 0.146,0.135 10 true A
*a View A
V100137

Front


Remove the 2 bolts.


b.

Disengage the 3 claws to remove the No. 1 air duct.

NOTICE:

Be careful not to deform or damage the lower heater case of the air conditioner unit assembly when removing the No. 1 air duct.



Hide 12.REMOVE FRONT WHEEL LH (for LHD)

Hide 13.REMOVE FRONT WHEEL RH (for RHD)

Hide 45220 14.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45253 15.REMOVE STEERING COLUMN HOLE COVER

a.

Turn back the floor carpet.


b.
C373453

Remove the clip.


c.

Disengage the 2 clips to remove the steering column hole cover.


Hide 45220 16.REMOVE STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C373454

Using a screwdriver, loosen the clamp as shown in the illustration.


b.
C373457C01
1.583,0.76 0.948,0.656 0.948,0.656 1.583,0.677 true 0.781,0.563 0.979,0.75 0.198,0.188 10 true *a
*a Matchmark


Remove the bolt and slide the steering intermediate shaft assembly.

NOTICE:

Do not remove the steering intermediate shaft assembly from the steering column assembly.



c.

Put matchmarks on the steering intermediate shaft assembly and steering column assembly.


d.

Remove the steering intermediate shaft assembly from the steering column assembly.


Hide 45250 17.REMOVE STEERING COLUMN ASSEMBLY

a.

Disconnect each connector and disengage each wire harness clamp from the steering column assembly.


b.
C373459

Remove the bolt, 2 nuts and steering column assembly.