Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB › 2017.09–2017.12
RM33A0E _52 Drivetrain _065359 AXLE AND DIFFERENTIAL _0319596 FRONT AXLE HUB A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front axle hub sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 89543 3.SEPARATE FRONT SPEED SENSOR

a.
C369722

Remove the bolt and separate the front speed sensor and front flexible hose from the front shock absorber assembly.

NOTICE:

Be sure to separate the front speed sensor and front flexible hose from the front shock absorber assembly completely.



b.
C369723

Remove the bolt, disengage the clamp and separate the front speed sensor from the front shock absorber assembly and steering knuckle.

NOTICE:
·

Prevent foreign matter from contacting the sensor tip.

·

Be careful not to damage the front speed sensor.

·

Clean the speed sensor installation hole and the contact surfaces every time the front speed sensor is removed.




Hide 45470 4.SEPARATE TIE ROD ASSEMBLY

Hide 5.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

Hide 43512 6.REMOVE FRONT DISC

Hide 48069 7.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

a.
C369724

Remove the bolt and 2 nuts and separate the front lower No. 1 suspension arm sub-assembly from the front lower ball joint assembly.


Hide 43420 8.SEPARATE FRONT DRIVE SHAFT ASSEMBLY

a.
C369725C01
2.74,0.406 3.146,0.406 3.146,0.406 3.146,1.573 true 2.885,0.667 3.146,0.667 true 3.094,1.583 3.406,1.74 0.313,0.156 10 false *a
*a Matchmark


Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.


b.
C369726

Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.

NOTICE:
·

Do not damage the front drive shaft outboard joint boot.

·

Do not push the front axle assembly towards the outside of the vehicle any further than necessary.



HINT:

If it is difficult to separate the front drive shaft assembly from the front axle assembly, tap the end of the front drive shaft assembly using a brass bar and a hammer.



Hide 9.REMOVE FRONT AXLE ASSEMBLY

a.
C369727

Remove the 2 bolts, 2 nuts and front axle assembly from the front shock absorber assembly.

NOTICE:

When removing the nuts, keep the bolts from rotating.



Hide 43502C 10.REMOVE FRONT AXLE HUB SUB-ASSEMBLY

a.
C369728

Secure the front axle assembly between aluminum plates in a vise.

NOTICE:

Do not overtighten the vise.



b.

Remove the 4 bolts, front axle hub sub-assembly and front disc brake dust cover from the steering knuckle.

NOTICE:
·

Do not drop the front axle hub sub-assembly.

·

Be careful not to damage the speed sensor rotor or contact surfaces.

·

Do not allow foreign matter to contact the speed sensor rotor or contact surfaces.