Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › ROOF DRIP SIDE FINISH MOULDING
RM33A0E _59 Vehicle Exterior _065397 EXTERIOR PANELS / TRIM _0319672 ROOF DRIP SIDE FINISH MOULDING A

EXTERIOR PANELS / TRIM  ROOF DRIP SIDE FINISH MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 75561A 1.INSTALL ROOF DRIP SIDE FINISH MOULDING CLIP

NOTICE:

When installing new roof drip side finish moulding clips, remove any double-sided tape remaining where the roof drip side finish moulding clips will be installed on the vehicle body and clean the vehicle body with a non-residue solvent.


a.
B470938C01
1,1.094 1.438,1.188 true 2.521,0.354 2.771,0.354 true 2.313,0.24 2.656,0.563 0.344,0.323 10 false *a 0.802,0.979 1.042,1.219 0.24,0.24 10 false *b
*a Adhesive
*b 2 to 3 mm Bead of Adhesive


Apply a 2 to 3 mm (0.0787 to 0.118 in.) bead of adhesive (3M DP-105 or equivalent) to each new roof drip side finish moulding clip.

HINT:

Adhesive strength (tensile strength): 13.7 MPa (140.0 kgf/cm2, 1987 psi) or more (when the temperature is 23°C (73°F).)



b.

Install the 2 roof drip side finish moulding clips to the positions on the roof panel shown in the illustration. Determine the locations and firmly press and install the 2 roof drip side finish moulding clips.

B470939N01
1.104,0.208 1.365,0.479 0.26,0.271 10 false A 1.781,0.25 2.042,0.521 0.26,0.271 10 false B 2.167,0.177 2.427,0.448 0.26,0.271 10 false C 4.677,1.594 4.938,1.865 0.26,0.271 10 false D 5.542,1.583 5.802,1.854 0.26,0.271 10 false E 6.385,1.583 6.646,1.854 0.26,0.271 10 false F 6.74,1.521 7,1.792 0.26,0.271 10 false G

Standard Measurement:
Area Measurement Area Measurement
A 4.5 to 5.5 mm (0.177 to 0.217 in.) B 3.6 mm (0.142 in.)
C 1.7 to 2.7 mm (0.0669 to 0.106 in.) D 5.0 mm (0.197 in.)
E 4.5 to 5.5 mm (0.177 to 0.217 in.) F 2.3 to 3.3 mm (0.0906 to 0.130 in.)
G 2.1 mm (0.0827 in.) - -



c.

Wait at least 40 minutes before installing the roof drip side finish moulding.

HINT:
·

Initial hardening time: 40 minutes

·

Complete hardening time: 24 hours




Hide 75552H 2.INSTALL ROOF DRIP SIDE FINISH MOULDING

a.

Engage the 2 clips to install the roof drip side finish moulding as shown in the illustration.

B470940N01
0.573,0.198 0.854,0.448 0.281,0.25 10 false A 6.5,1.323 6.781,1.573 0.281,0.25 10 false B

Standard Measurement:
Area Measurement Area Measurement
A 0.8 mm (0.0315 in.) B 6.2 mm (0.244 in.)