Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR
RM33A0E _59 Vehicle Exterior _065394 WIPER / WASHER _0320458 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

Make sure to hold the front wiper arm while lifting it as lifting the front wiper arm by the front wiper blade may damage or deform the front wiper blade.


PROCEDURE

Hide 85110 1.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

a.

Using a T30 "TORX" socket wrench, install the windshield wiper motor assembly to the wiper link assembly with the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.
E364791C01
1.948,0.885 2.698,0.438 true 2.698,0.302 3.01,0.458 0.313,0.156 10 false *a
*a Pivot of Windshield Wiper Motor Assembly


Apply MP grease to the pivot of the windshield wiper motor assembly.


c.
E364792C01
2.302,0.938 2.823,1.427 true 1.375,0.667 1.771,0.344 true 2.823,1.417 3.135,1.573 0.313,0.156 10 false *a 1.781,0.208 2.094,0.365 0.313,0.156 10 false *1
*1 No. 1 Wiper Link Rod
*a Pivot of Windshield Wiper Motor Assembly


Connect the No. 1 wiper link rod to the pivot of the windshield wiper motor assembly.


Hide 2.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

a.
E364793C02
0.677,2.906 0.531,2.688 true 0.625,2.906 0.833,3.063 0.208,0.156 10 true *a 0.406,0.49 0.563,0.688 0.156,0.198 10 true 2 3.219,0.542 3.375,0.74 0.156,0.198 10 true 1
*a Motor Grommet


Engage the motor grommet as shown in the illustration.

NOTICE:

Be careful not to damage the windshield glass when installing the windshield wiper motor and link assembly.



b.

Install the windshield wiper motor and link assembly with the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)

HINT:

Tighten the bolts in the order shown in the illustration.



c.

Connect the connector.


d.

Engage the 2 clamps.


Hide 55708 3.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.

Insert the cowl top ventilator louver sub-assembly from the front passenger side as shown in the illustration.

E374987C01
3.76,3.094 3.969,3.417 3.969,3.417 4.208,3.188 true 6.448,3.333 6.615,3.063 true 3.906,3.427 4.094,3.615 0.188,0.188 10 true *a 6.365,3.344 6.552,3.531 0.188,0.188 10 true *a
*a Vehicle Body - -
V113147

Install in this Direction - -


NOTICE:

Make sure that the cowl top ventilator louver sub-assembly does not contact the vehicle body, otherwise it may be damaged.



b.

Lower the cowl top ventilator louver sub-assembly as shown in the illustration.

E374988C01
6.313,2.083 6.448,1.813 true 6.229,2.094 6.417,2.281 0.188,0.188 10 true *a
*a Vehicle Body - -
V113147

Install in this Direction - -


NOTICE:

Make sure that the cowl top ventilator louver sub-assembly does not contact the vehicle body, otherwise it may be damaged.



c.

Push the front passenger side of the cowl top ventilator louver sub-assembly and set it in the position shown in the illustration.

E374989C01
0,0 0,0 false
V113147

Install in this Direction - -



d.

Engage the guide.

E374990C01
4.646,0.563 4.885,0.656 true 4.438,0.427 4.635,0.615 0.198,0.188 10 true *a
*a Guide - -


NOTICE:

Make sure to engage the guides securely, otherwise the cowl top ventilator louver sub-assembly may pop up when engaging it to the windshield glass.



e.

Engage the cowl top ventilator louver sub-assembly to the windshield glass as shown in the illustration.


f.

Engage the 4 claws as shown in the illustration.

E374991C01
0,0 0,0 false
V113147

Install in this Direction - -



g.

Install the 2 clips.


Hide 53867H 4.INSTALL FRONT FENDER TO COWL SIDE SEAL LH

a.

Engage the 2 guides and 3 claws to install the front fender to cowl side seal LH.


Hide 53866J 5.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

a.

Engage the 2 guides and 3 claws to install the front fender to cowl side seal RH.


Hide 6.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

a.

When reusing the front wiper arm and blade assembly RH:

i.
E364795C01
0.771,1.271 1.427,1.427 true 2.188,3.313 2.719,3.26 true 0.604,1.167 0.917,1.323 0.313,0.156 10 false *a 2.76,3.177 3.073,3.333 0.313,0.156 10 false *a
*a Serration


Clean the wiper arm serrations to remove any burrs, dirt, etc.

NOTICE:

Do not grind down the wiper arm serrations.




b.

When reusing the windshield wiper motor and link assembly:

i.

Clean the wiper pivot serrations with a wire brush.



c.

Turn the ignition switch to on.


d.

Operate the windshield wiper motor assembly and stop the windshield wiper motor and link assembly at the automatic stop position.


e.

Turn the ignition switch off.


f.
E379219C01
1.24,0.604 1.542,0.438 true 0.677,0.281 0.833,0.479 0.156,0.198 10 true A 0.635,0.5 0.792,0.698 0.156,0.198 10 true A 1.563,0.292 1.75,0.479 0.188,0.188 10 true *a
*a Alignment Mark


Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)

HINT:

Hold the wiper arm by hand while tightening the nut.


Reference Measurement:
Area Measurement
A 7.5 mm (0.295 in.)



Hide 7.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

a.

When reusing the front wiper arm and blade assembly LH:

i.
E364797C01
2.188,3.333 2.74,3.26 true 0.823,1.26 1.438,1.417 true 0.646,1.146 0.958,1.302 0.313,0.156 10 false *a 2.781,3.167 3.094,3.323 0.313,0.156 10 false *a
*a Serration


Clean the wiper arm serrations to remove any burrs, dirt, etc.

NOTICE:

Do not grind down the wiper arm serrations.




b.

When reusing the windshield wiper motor and link assembly:

i.

Clean the wiper pivot serrations with a wire brush.



c.
E379220C01
0.917,2.469 1.25,2.313 true 0.26,2.271 0.396,2.448 0.135,0.177 10 true A 1.271,2.188 1.469,2.365 0.198,0.177 10 true *a 0.26,2.5 0.396,2.677 0.135,0.177 10 true A
*a Alignment Mark


Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)

HINT:

Hold the wiper arm by hand while tightening the nut.


Reference Measurement:
Area Measurement
A 7.5 mm (0.295 in.)



d.

Turn the ignition switch to on.


e.

Operate the windshield wipers while spraying washer fluid onto the windshield glass. Make sure that the windshield wipers function properly and the wipers do not contact the vehicle body.


f.

Turn the ignition switch off.


g.

Lift each wiper arm twice after the wipers stop and check the wiper set position.


Hide 85292B 8.INSTALL FRONT WIPER ARM HEAD CAP

a.
E364799

Engage the 3 claws to install the front wiper arm head cap.

HINT:

Use the same procedure for the RH side and LH side.