Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR
RM33A0E _59 Vehicle Exterior _065394 WIPER / WASHER _0320458 FRONT WIPER MOTOR G

WIPER / WASHER  FRONT WIPER MOTOR  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 85110 1.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY (for LHD)

a.
E379219C01
1.24,0.604 1.542,0.438 true 0.677,0.281 0.833,0.479 0.156,0.198 10 true A 0.635,0.5 0.792,0.698 0.156,0.198 10 true A 1.563,0.292 1.75,0.479 0.188,0.188 10 true *a
*a Alignment Mark


for RH Side:

i.

Operate the windshield wiper motor assembly.


ii.

Stop the windshield wiper motor assembly operation.


iii.

Check the automatic stop (park) position.

HINT:

After the front wiper motor is stopped, check the automatic stop position after lifting the wiper blade 2 times.


Standard Clearance:
Area Measurement
A 7.5 mm (0.295 in.)


OK:

The front wiper stops at the position shown in the illustration.




b.
E379220C01
0.917,2.469 1.25,2.313 true 0.26,2.271 0.396,2.448 0.135,0.177 10 true A 1.271,2.188 1.469,2.365 0.198,0.177 10 true *a 0.26,2.5 0.396,2.677 0.135,0.177 10 true A
*a Alignment Mark


for LH Side:

i.

Operate the windshield wiper motor assembly.


ii.

Stop the windshield wiper motor assembly operation.


iii.

Check the automatic stop (park) position.

HINT:

After the front wiper motor is stopped, check the automatic stop position after lifting the wiper blade 2 times.


Standard Clearance:
Area Measurement
A 7.5 mm (0.295 in.)


OK:

The front wiper stops at the position shown in the illustration.




Hide 85110 2.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY (for RHD)

a.
E380213C01
2.208,2.313 2.521,2.479 true 1.979,2.177 2.177,2.354 0.198,0.177 10 true *a 3.021,2.292 3.208,2.458 0.188,0.167 10 true A 3.021,2.51 3.208,2.677 0.188,0.167 10 true A
*a Alignment Mark


for RH Side:

i.

Operate the windshield wiper motor assembly.


ii.

Stop the windshield wiper motor assembly operation.


iii.

Check the automatic stop (park) position.

HINT:

After the front wiper motor is stopped, check the automatic stop position after lifting the wiper blade 2 times.


Standard Clearance:
Area Measurement
A 7.5 mm (0.295 in.)


OK:

The front wiper stops at the position shown in the illustration.




b.
E380212C01
2.188,0.615 1.708,0.344 true 1.448,0.219 1.667,0.406 0.219,0.188 10 true *a 2.594,0.292 2.75,0.469 0.156,0.177 10 true A 2.646,0.531 2.802,0.708 0.156,0.177 10 true A
*a Alignment Mark


for LH Side:

i.

Operate the windshield wiper motor assembly.


ii.

Stop the windshield wiper motor assembly operation.


iii.

Check the automatic stop (park) position.

HINT:

After the front wiper motor is stopped, check the automatic stop position after lifting the wiper blade 2 times.


Standard Clearance:
Area Measurement
A 7.5 mm (0.295 in.)


OK:

The front wiper stops at the position shown in the illustration.