Home › Vehicle Exterior › WIPER / WASHER › RAIN SENSOR
RM33A0E _59 Vehicle Exterior _065394 WIPER / WASHER _0320465 RAIN SENSOR G

WIPER / WASHER  RAIN SENSOR  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 89941 1.INSPECT RAIN SENSOR (for LHD)

a.
E267170C47
1.438,0.333 1.833,0.573 0.396,0.24 1.563,1.313 0.906,0.625 false 1.979,1.313 2.635,0.625 false 0.094,0.104 0.344,0.292 0.25,0.188 10 false *a 0.74,0.417 1.031,0.604 0.292,0.188 10 false ES 2.542,0.417 2.833,0.604 0.292,0.188 10 false SIG 1.531,0.354 1.823,0.542 0.292,0.188 10 false V4
*a Front view of wire harness connector
(to Rain Sensor)


Disconnect the V4 rain sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
V4-4 (SIG) - V4-2 (ES) Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V4-2 (ES) - Body ground Always Below 1 Ω


If the result is not as specified, repair or replace the harness or connector.


d.
E257042C15
1.635,0.969 1.125,0.448 false 1.781,0.969 2.292,0.448 false 0.083,0.073 0.313,0.26 0.229,0.188 10 false *a 2.25,0.271 2.708,0.427 0.458,0.156 10 false ES 0.927,0.26 1.438,0.417 0.51,0.156 10 false MPX
*a Component with harness connected
(Rain Sensor)


Connect the V4 rain sensor connector.


e.

Connect an oscilloscope to the rain sensor connector.


f.

Check for pulses.

OK:
Tester Connection Condition Specified Condition
3 (MPX) - 2 (ES) Ignition switch ON Pulse generation


If the result is not as specified, replace the rain sensor.


Hide 89941 2.INSPECT RAIN SENSOR (for RHD)

a.
E267170C48
1.438,0.333 1.833,0.573 0.396,0.24 1.563,1.313 0.906,0.625 false 1.979,1.313 2.635,0.625 false 0.094,0.104 0.344,0.292 0.25,0.188 10 false *a 0.74,0.417 1.031,0.604 0.292,0.188 10 false ES 2.542,0.417 2.833,0.604 0.292,0.188 10 false SIG 1.531,0.354 1.823,0.542 0.292,0.188 10 false V5
*a Front view of wire harness connector
(to Rain Sensor)


Disconnect the V5 rain sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
V5-4 (SIG) - V5-2 (ES) Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V5-2 (ES) - Body ground Always Below 1 Ω


If the result is not as specified, repair or replace the harness or connector.


d.
E257042C15
1.635,0.969 1.125,0.448 false 1.781,0.969 2.292,0.448 false 0.083,0.073 0.313,0.26 0.229,0.188 10 false *a 2.25,0.271 2.708,0.427 0.458,0.156 10 false ES 0.927,0.26 1.438,0.417 0.51,0.156 10 false MPX
*a Component with harness connected
(Rain Sensor)


Connect the V5 rain sensor connector.


e.

Connect an oscilloscope to the rain sensor connector.


f.

Check for pulses.

OK:
Tester Connection Condition Specified Condition
3 (MPX) - 2 (ES) Ignition switch ON Pulse generation


If the result is not as specified, replace the rain sensor.