Home › Drivetrain › U760E (AUTOMATIC TRANSMISSION / TRANSAXLE) › VALVE BODY ASSEMBLY › 2017.09–2021.02
RM33A0E _52 Drivetrain _065350 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0321091 VALVE BODY ASSEMBLY A

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  VALVE BODY ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 35418 1.INSTALL MANUAL VALVE

a.

Coat the manual valve with Toyota Genuine ATF WS and install it to the transmission valve body assembly.


Hide 35148 2.INSTALL TRANSAXLE CASE GASKET

a.

Coat 2 new transaxle case gaskets with Toyota Genuine ATF WS.


b.

Install the 2 transaxle case gaskets to the automatic transaxle assembly.


Hide 35410 3.INSTALL TRANSMISSION VALVE BODY ASSEMBLY

a.

Coat the O-ring of the transmission wire with Toyota Genuine ATF WS.


b.
C379919C02
1.969,0.823 2.031,0.667 2.031,0.667 2.177,0.667 true 1.375,0.74 1.521,0.74 1.521,0.74 1.688,0.917 true 1.208,0.646 1.448,0.854 0.24,0.208 10 false *b 2.219,0.563 2.5,0.771 0.281,0.208 10 false *1 3.094,2.813 3.313,3.021 0.219,0.208 10 false *a 1.26,1.917 1.417,2.104 0.156,0.188 10 false B 0.917,1.906 1.073,2.094 0.156,0.188 10 false D 1.875,1.927 2.031,2.115 0.156,0.188 10 false A 2.948,2.823 3.104,3.01 0.156,0.188 10 false B 0.177,2.75 0.333,2.938 0.156,0.188 10 false C 0.188,3.25 0.344,3.438 0.156,0.188 10 false B 0.854,3.99 1.01,4.177 0.156,0.188 10 false B 0.198,3.406 0.417,3.615 0.219,0.208 10 false *a 1.177,3.813 1.333,4 0.156,0.188 10 false A 1.563,3.792 1.719,3.979 0.156,0.188 10 false A 1.917,3.792 2.073,3.979 0.156,0.188 10 false A 2.281,3.781 2.438,3.969 0.156,0.188 10 false A
*1 Manual Valve
*a Positioning Bolt
*b Manual Valve Lever Shaft Sub-assembly Pin


Insert the manual valve lever shaft sub-assembly pin into the groove on the end of the manual valve as shown in the illustration and temporarily install the transmission valve body assembly to the transaxle case sub-assembly with the 11 bolts.

NOTICE:
·

When installing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and transaxle case sub-assembly to interfere with each other.

·

Be sure to insert the manual valve lever shaft sub-assembly pin into the groove on the end of the manual valve.



Bolt Length
Bolt Length [mm (in.)]
(A) 25 (0.984)
(B) 30 (1.18)
(C) and (D) 35 (1.38)


c.

Fully tighten the 2 positioning bolts shown in the illustration.

Torque:
10.8 N*m (110 kgf*cm, 8 ft.*lbf)


d.

Fully tighten the 9 bolts to install the transmission valve body assembly.

Torque:
Bolt (A), (B), (C) : 10.8 N*m (110 kgf*cm, 8 ft.*lbf)
Bolt (D) : 9.6 N*m (98 kgf*cm, 85 in.*lbf)


Hide 35330 4.INSTALL VALVE BODY OIL STRAINER ASSEMBLY

a.

Coat a new O-ring with Toyota Genuine ATF WS and install it to the valve body oil strainer assembly.

NOTICE:

Ensure that the O-ring is not twisted.



b.

Install the valve body oil strainer assembly to the transmission valve body assembly with the 2 bolts.

Torque:
9.6 N*m (98 kgf*cm, 85 in.*lbf)


Hide 35394 5.INSTALL TRANSMISSION OIL CLEANER MAGNET

a.
C317184C01
1.885,0.635 1.885,0.24 1.885,0.24 0.479,0.24 false 1.542,0.76 1.542,0.24 false 1.073,1.604 1.073,0.24 false 0.823,1.177 0.823,0.24 false 0.292,0.167 0.531,0.396 0.24,0.229 10 false *1
*1 Transmission Oil Cleaner Magnet


Install the 4 transmission oil cleaner magnets to the automatic transaxle oil pan sub-assembly as shown in the illustration.


Hide 35168A 6.INSTALL AUTOMATIC TRANSAXLE OIL PAN GASKET

a.

Install a new automatic transaxle oil pan gasket to the automatic transaxle oil pan sub-assembly.


Hide 35106D 7.INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

a.
C379920

Clean and degrease the 2 bolts and installation holes in the automatic transaxle assembly.


b.
C379921

Install the automatic transaxle oil pan sub-assembly with automatic transaxle oil pan gasket to the automatic transaxle assembly with the 17 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)

NOTICE:

Completely remove any oil or grease from the contact surfaces of the automatic transaxle assembly and automatic transaxle oil pan sub-assembly with automatic transaxle oil pan gasket before installation.



c.
P000601C44
1.979,1.177 2.177,0.229 2.177,0.229 2.302,0.229 false 2.323,0.135 2.521,0.323 0.198,0.188 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads on the ends of the 2 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

In order to ensure proper installation of the 2 bolts, apply adhesive to the 2 bolts and install them within 10 minutes of adhesive application.



d.
C379922

Install the 2 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)