Home › Drivetrain › U760E (AUTOMATIC TRANSMISSION / TRANSAXLE) › OIL PUMP › 2017.09–2021.02
RM33A0E _52 Drivetrain _065350 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0321095 OIL PUMP A

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  OIL PUMP  REASSEMBLY  


PROCEDURE

Hide 35301A 1.INSTALL FRONT OIL PUMP OIL SEAL

a.
C188149N05
1.313,2.052 1.042,2.052 false 2.438,1.333 2.333,1.333 2.333,1.333 1.781,0.906 false 2.49,1.24 2.99,1.531 0.5,0.292 10 false SST 0.719,1.958 1.01,2.115 0.292,0.156 10 false SST

Coat the lip of a new front oil pump oil seal with a small amount of MP grease.


b.

Using SST and a hammer, install the front oil pump oil seal to the front oil pump body sub-assembly.

SST
09350-32014  (09351-32140)

Standard Depth:

-0.25 to 0.25 mm (-0.00984 to 0.00984 in.)


NOTICE:

The seal end should be level with the outer edge of the front oil pump body sub-assembly.



Hide 35301B 2.INSTALL FRONT OIL PUMP BODY O-RING

a.
C138278

Coat a new front oil pump body O-ring with Toyota Genuine ATF WS and install it to the front oil pump body sub-assembly.

NOTICE:

Ensure that the front oil pump body O-ring is not twisted.



Hide 35322 3.INSTALL FRONT OIL PUMP DRIVEN GEAR

a.
C301310

Coat the front oil pump driven gear with Toyota Genuine ATF WS and install it to the front oil pump body sub-assembly with the marked side facing upward.


Hide 35321 4.INSTALL FRONT OIL PUMP DRIVE GEAR

a.
C301309

Coat the front oil pump drive gear with Toyota Genuine ATF WS, and install it to the front oil pump body sub-assembly with the marked side facing upward.


Hide 35370 5.INSTALL STATOR SHAFT ASSEMBLY

a.
C138275N09
1.427,2.573 1.573,2.74 0.146,0.167 10 false B 0.771,1.188 0.917,1.354 0.146,0.167 10 false A 1.01,0.573 1.156,0.74 0.146,0.167 10 false A 1.646,0.229 1.792,0.396 0.146,0.167 10 false A 2.281,0.521 2.427,0.688 0.146,0.167 10 false A 2.583,0.979 2.729,1.146 0.146,0.167 10 false A 2.552,1.615 2.698,1.781 0.146,0.167 10 false A 2.198,2.115 2.344,2.281 0.146,0.167 10 false A 1.708,2.229 1.854,2.396 0.146,0.167 10 false A 1,1.865 1.135,2.031 0.135,0.167 10 false A 2.219,2.781 2.365,2.948 0.146,0.167 10 false B 2.427,3.323 2.573,3.49 0.146,0.167 10 false B 2.375,4.052 2.521,4.219 0.146,0.167 10 false B 0.875,3.833 1.021,4 0.146,0.167 10 false B 0.896,3.083 1.042,3.25 0.146,0.167 10 false B 1.344,4.271 1.49,4.438 0.146,0.167 10 false B

Align each knock pin of the stator shaft assembly with the holes in the front oil pump body sub-assembly and install the stator shaft assembly to the front oil pump body sub-assembly.


b.

Using a T30 "TORX" socket wrench, install the 16 bolts.

Torque:
9.3 N*m (95 kgf*cm, 82 in.*lbf)

Bolt Length:
Bolt (A):

14 mm (0.551 in.)

Bolt (B):

26 mm (1.02 in.)



Hide 6.INSPECT FRONT OIL PUMP BODY SUB-ASSEMBLY